blob: c3a60d6087bb404d343768d0f50d62fc8c902158 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2014 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <i2c.h>
#include <hwconfig.h>
#include <init.h>
#include <asm/mmu.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include <asm/mpc85xx_gpio.h>
DECLARE_GLOBAL_DATA_PTR;
struct board_specific_parameters {
u32 n_ranks;
u32 datarate_mhz_high;
u32 rank_gb;
u32 clk_adjust;
u32 wrlvl_start;
u32 wrlvl_ctl_2;
u32 wrlvl_ctl_3;
};
/*
* datarate_mhz_high values need to be in ascending order
*/
static const struct board_specific_parameters udimm0[] = {
/*
* memory controller 0
* num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
* ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
*/
#if defined(CONFIG_SYS_FSL_DDR4)
{2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
{2, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,},
{1, 1666, 0, 8, 6, 0x0708090B, 0x0C0D0E09,},
{1, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,},
{1, 2200, 0, 8, 7, 0x08090A0D, 0x0F0F100C,},
#elif defined(CONFIG_SYS_FSL_DDR3)
{2, 833, 0, 8, 6, 0x06060607, 0x08080807,},
{2, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
{2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
{1, 833, 0, 8, 6, 0x06060607, 0x08080807,},
{1, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
{1, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
#else
#error DDR type not defined
#endif
{}
};
static const struct board_specific_parameters *udimms[] = {
udimm0,
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
struct cpu_type *cpu = gd->arch.cpu;
if (ctrl_num > 2) {
printf("Not supported controller number %d\n", ctrl_num);
return;
}
if (!pdimm->n_ranks)
return;
pbsp = udimms[0];
/* Get clk_adjust according to the board ddr freqency and n_banks
* specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
while (pbsp->datarate_mhz_high) {
if (pbsp->n_ranks == pdimm->n_ranks &&
(pdimm->rank_density >> 30) >= pbsp->rank_gb) {
if (ddr_freq <= pbsp->datarate_mhz_high) {
popts->clk_adjust = pbsp->clk_adjust;
popts->wrlvl_start = pbsp->wrlvl_start;
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
goto found;
}
pbsp_highest = pbsp;
}
pbsp++;
}
if (pbsp_highest) {
printf("Error: board specific timing not found\n");
printf("for data rate %lu MT/s\n", ddr_freq);
printf("Trying to use the highest speed (%u) parameters\n",
pbsp_highest->datarate_mhz_high);
popts->clk_adjust = pbsp_highest->clk_adjust;
popts->wrlvl_start = pbsp_highest->wrlvl_start;
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
} else {
panic("DIMM is not supported by this board");
}
found:
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 1;
/*
* Write leveling override
*/
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xf;
/*
* rtt and rtt_wr override
*/
popts->rtt_override = 0;
/* Enable ZQ calibration */
popts->zq_en = 1;
/* DHC_EN =1, ODT = 75 Ohm */
#ifdef CONFIG_SYS_FSL_DDR4
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
#else
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
/* optimize cpo for erratum A-009942 */
popts->cpo_sample = 0x5f;
#endif
/* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
* set DDR bus width to 32bit for T1023
*/
if (cpu->soc_ver == SVR_T1023)
popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
/* for DDR bus 32bit test on T1024 */
popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
#endif
}
#if defined(CONFIG_DEEP_SLEEP)
void board_mem_sleep_setup(void)
{
void __iomem *qixis_base = (void *)QIXIS_BASE;
/* does not provide HW signals for power management */
clrbits_8(qixis_base + 0x21, 0x2);
/* Disable MCKE isolation */
gpio_set_value(2, 0);
udelay(1);
}
#endif
int dram_init(void)
{
phys_size_t dram_size;
#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
puts("Initializing....using SPD\n");
dram_size = fsl_ddr_sdram();
#else
/* DDR has been initialised by first stage boot loader */
dram_size = fsl_ddr_sdram_size();
#endif
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
dram_size *= 0x100000;
#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
fsl_dp_resume();
#endif
gd->ram_size = dram_size;
return 0;
}