| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Configuration header file for K3 J721S2 EVM |
| * |
| * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ |
| * David Huang <d-huang@ti.com> |
| */ |
| |
| #ifndef __CONFIG_J721S2_EVM_H |
| #define __CONFIG_J721S2_EVM_H |
| |
| #include <linux/sizes.h> |
| #include <config_distro_bootcmd.h> |
| #include <environment/ti/mmc.h> |
| #include <environment/ti/k3_rproc.h> |
| #include <environment/ti/ufs.h> |
| #include <environment/ti/k3_dfu.h> |
| |
| /* DDR Configuration */ |
| #define CONFIG_SYS_SDRAM_BASE1 0x880000000 |
| |
| /* SPL Loader Configuration */ |
| #if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM) |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \ |
| CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE) |
| #define CONFIG_SYS_UBOOT_BASE 0x50280000 |
| /* Image load address in RAM for DFU boot*/ |
| #else |
| #define CONFIG_SYS_UBOOT_BASE 0x50080000 |
| /* |
| * Maximum size in memory allocated to the SPL BSS. Keep it as tight as |
| * possible (to allow the build to go through), as this directly affects |
| * our memory footprint. The less we use for BSS the more we have available |
| * for everything else. |
| */ |
| #define CONFIG_SPL_BSS_MAX_SIZE 0xA000 |
| /* |
| * Link BSS to be within SPL in a dedicated region located near the top of |
| * the MCU SRAM, this way making it available also before relocation. Note |
| * that we are not using the actual top of the MCU SRAM as there is a memory |
| * location filled in by the boot ROM that we want to read out without any |
| * interference from the C context. |
| */ |
| #define CONFIG_SPL_BSS_START_ADDR (0x41c80000 -\ |
| CONFIG_SPL_BSS_MAX_SIZE) |
| /* Set the stack right below the SPL BSS section */ |
| #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR |
| /* Configure R5 SPL post-relocation malloc pool in DDR */ |
| #define CONFIG_SYS_SPL_MALLOC_START 0x84000000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M |
| /* Image load address in RAM for DFU boot*/ |
| #endif |
| |
| #ifdef CONFIG_SYS_K3_SPL_ATF |
| #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin" |
| #endif |
| |
| #define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE |
| |
| #define CONFIG_SYS_BOOTM_LEN SZ_64M |
| #define CONFIG_CQSPI_REF_CLK 133333333 |
| |
| /* HyperFlash related configuration */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1 |
| |
| /* U-Boot general configuration */ |
| #define EXTRA_ENV_J721S2_BOARD_SETTINGS \ |
| "default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ |
| "findfdt=" \ |
| "setenv name_fdt ${default_device_tree};" \ |
| "setenv fdtfile ${name_fdt}\0" \ |
| "name_kern=Image\0" \ |
| "console=ttyS2,115200n8\0" \ |
| "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02880000 " \ |
| "${mtdparts}\0" \ |
| "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0" |
| |
| #define PARTS_DEFAULT \ |
| /* Linux partitions */ \ |
| "uuid_disk=${uuid_gpt_disk};" \ |
| "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0" |
| |
| #ifdef CONFIG_SYS_K3_SPL_ATF |
| #if defined(CONFIG_TARGET_J721S2_R5_EVM) |
| #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \ |
| "addr_mcur5f0_0load=0x89000000\0" \ |
| "name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0" |
| #elif defined(CONFIG_TARGET_J7200_R5_EVM) |
| #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \ |
| "addr_mcur5f0_0load=0x89000000\0" \ |
| "name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0" |
| #endif /* CONFIG_TARGET_J721S2_R5_EVM */ |
| #else |
| #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC "" |
| #endif /* CONFIG_SYS_K3_SPL_ATF */ |
| |
| /* U-Boot MMC-specific configuration */ |
| #define EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC \ |
| "boot=mmc\0" \ |
| "mmcdev=1\0" \ |
| "bootpart=1:2\0" \ |
| "bootdir=/boot\0" \ |
| EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \ |
| "rd_spec=-\0" \ |
| "init_mmc=run args_all args_mmc\0" \ |
| "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \ |
| "get_overlay_mmc=" \ |
| "fdt address ${fdtaddr};" \ |
| "fdt resize 0x100000;" \ |
| "for overlay in $name_overlays;" \ |
| "do;" \ |
| "load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && " \ |
| "fdt apply ${dtboaddr};" \ |
| "done;\0" \ |
| "partitions=" PARTS_DEFAULT \ |
| "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \ |
| "${bootdir}/${name_kern}\0" \ |
| "get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \ |
| "${bootdir}/${name_fit}\0" \ |
| "partitions=" PARTS_DEFAULT |
| |
| /* Set the default list of remote processors to boot */ |
| #if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM) |
| #ifdef DEFAULT_RPROCS |
| #undef DEFAULT_RPROCS |
| #endif |
| #endif |
| |
| #ifdef CONFIG_TARGET_J721S2_A72_EVM |
| #define DEFAULT_RPROCS "" \ |
| "2 /lib/firmware/j721s2-main-r5f0_0-fw " \ |
| "3 /lib/firmware/j721s2-main-r5f0_1-fw " \ |
| "4 /lib/firmware/j721s2-main-r5f1_0-fw " \ |
| "5 /lib/firmware/j721s2-main-r5f1_1-fw " \ |
| "6 /lib/firmware/j721s2-c71_0-fw " \ |
| "7 /lib/firmware/j721s2-c71_1-fw " |
| #endif /* CONFIG_TARGET_J721S2_A72_EVM */ |
| |
| #ifdef CONFIG_TARGET_J7200_A72_EVM |
| #define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY \ |
| "do_main_cpsw0_qsgmii_phyinit=1\0" \ |
| "init_main_cpsw0_qsgmii_phy=gpio set gpio@22_17;" \ |
| "gpio clear gpio@22_16\0" \ |
| "main_cpsw0_qsgmii_phyinit=" \ |
| "if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \ |
| "test ${boot} = mmc; then " \ |
| "run init_main_cpsw0_qsgmii_phy;" \ |
| "fi;\0" |
| #define DEFAULT_RPROCS "" \ |
| "2 /lib/firmware/j7200-main-r5f0_0-fw " \ |
| "3 /lib/firmware/j7200-main-r5f0_1-fw " |
| #endif /* CONFIG_TARGET_J7200_A72_EVM */ |
| |
| #ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY |
| #define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY |
| #endif |
| |
| /* set default dfu_bufsiz to 128KB (sector size of OSPI) */ |
| #define EXTRA_ENV_DFUARGS \ |
| DFU_ALT_INFO_MMC \ |
| DFU_ALT_INFO_EMMC \ |
| DFU_ALT_INFO_RAM \ |
| DFU_ALT_INFO_OSPI |
| |
| #if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM) |
| #define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD \ |
| "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ |
| "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" |
| #else |
| #define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD |
| #endif |
| |
| /* Incorporate settings into the U-Boot environment */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| DEFAULT_LINUX_BOOT_ENV \ |
| DEFAULT_MMC_TI_ARGS \ |
| DEFAULT_FIT_TI_ARGS \ |
| EXTRA_ENV_J721S2_BOARD_SETTINGS \ |
| EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC \ |
| EXTRA_ENV_RPROC_SETTINGS \ |
| EXTRA_ENV_DFUARGS \ |
| DEFAULT_UFS_TI_ARGS \ |
| EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD \ |
| EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY |
| |
| /* Now for the remaining common defines */ |
| #include <configs/ti_armv7_common.h> |
| |
| /* MMC ENV related defines */ |
| |
| #endif /* __CONFIG_J721S2_EVM_H */ |