| /* |
| * (C) Copyright 2003 |
| * Texas Instruments. |
| * Kshitij Gupta <kshitij@ti.com> |
| * Configuation settings for the TI OMAP Innovator board. |
| * |
| * (C) Copyright 2004 |
| * ARM Ltd. |
| * Philippe Robin, <philippe.robin@arm.com> |
| * Configuration for Integrator AP board. |
| *. |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #define CFG_MEMTEST_START 0x100000 |
| #define CFG_MEMTEST_END 0x10000000 |
| #define CFG_HZ 1000 |
| #define CFG_HZ_CLOCK 24000000 /* Timer 1 is clocked at 24Mhz */ |
| #define CFG_TIMERBASE 0x13000100 /* Timer1 */ |
| |
| #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS 1 |
| #define CONFIG_MISC_INIT_R 1 /* call misc_init_r during start up */ |
| |
| #undef CONFIG_INIT_CRITICAL |
| #define CONFIG_CM_INIT 1 |
| #define CONFIG_CM_REMAP 1 |
| #undef CONFIG_CM_SPD_DETECT |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CFG_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) |
| #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ |
| |
| /* |
| * PL010 Configuration |
| */ |
| #define CONFIG_PL010_SERIAL |
| #define CONFIG_CONS_INDEX 0 |
| #define CONFIG_BAUDRATE 38400 |
| #define CONFIG_PL01x_PORTS { (void *) (CFG_SERIAL0), (void *) (CFG_SERIAL1) } |
| #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| #define CFG_SERIAL0 0x16000000 |
| #define CFG_SERIAL1 0x17000000 |
| |
| /*#define CONFIG_NET_MULTI */ |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| |
| #define CONFIG_CMD_IMI |
| #define CONFIG_CMD_BDI |
| #define CONFIG_CMD_MEMORY |
| |
| |
| #define CONFIG_BOOTDELAY 2 |
| #define CONFIG_BOOTARGS "root=/dev/mtdblock0 mem=32M console=ttyAM0 console=tty" |
| #define CONFIG_BOOTCOMMAND "" |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "Integrator-AP # " /* Monitor Command Prompt */ |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| /* Print Buffer Size */ |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ |
| #define CFG_LOAD_ADDR 0x7fc0 /* default load address */ |
| |
| /*----------------------------------------------------------------------- |
| * Stack sizes |
| * |
| * The stack sizes are set up in start.S using the settings below |
| */ |
| #define CONFIG_STACKSIZE (128*1024) /* regular stack */ |
| #ifdef CONFIG_USE_IRQ |
| #define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ |
| #define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * Physical Memory Map |
| */ |
| #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ |
| #define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ |
| #define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ |
| |
| #define CFG_FLASH_BASE 0x24000000 |
| |
| /*----------------------------------------------------------------------- |
| * FLASH and environment organization |
| */ |
| #define CONFIG_ENV_IS_NOWHERE |
| #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define PHYS_FLASH_SIZE 0x01000000 /* 16MB */ |
| /* timeout values are in ticks */ |
| #define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* Timeout for Flash Erase */ |
| #define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* Timeout for Flash Write */ |
| #define CFG_MAX_FLASH_SECT 128 |
| #define CONFIG_ENV_SIZE 32768 |
| |
| #define PHYS_FLASH_1 (CFG_FLASH_BASE) |
| |
| /*----------------------------------------------------------------------- |
| * PCI definitions |
| */ |
| |
| /*#define CONFIG_PCI /--* include pci support */ |
| #undef CONFIG_PCI_PNP |
| #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ |
| #define DEBUG |
| |
| #define CONFIG_EEPRO100 |
| #define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ |
| |
| |
| #define INTEGRATOR_BOOT_ROM_BASE 0x20000000 |
| #define INTEGRATOR_HDR0_SDRAM_BASE 0x80000000 |
| |
| /* PCI Base area */ |
| #define INTEGRATOR_PCI_BASE 0x40000000 |
| #define INTEGRATOR_PCI_SIZE 0x3FFFFFFF |
| |
| /* memory map as seen by the CPU on the local bus */ |
| #define CPU_PCI_IO_ADRS 0x60000000 /* PCI I/O space base */ |
| #define CPU_PCI_IO_SIZE 0x10000 |
| |
| #define CPU_PCI_CNFG_ADRS 0x61000000 /* PCI config space */ |
| #define CPU_PCI_CNFG_SIZE 0x1000000 |
| |
| #define PCI_MEM_BASE 0x40000000 /* 512M to xxx */ |
| /* unused 256M from A0000000-AFFFFFFF might be used for I2O ??? */ |
| #define INTEGRATOR_PCI_IO_BASE 0x60000000 /* 16M to xxx */ |
| /* unused (128-16)M from B1000000-B7FFFFFF */ |
| #define PCI_CONFIG_BASE 0x61000000 /* 16M to xxx */ |
| /* unused ((128-16)M - 64K) from XXX */ |
| |
| #define PCI_V3_BASE 0x62000000 |
| |
| /* V3 PCI bridge controller */ |
| #define V3_BASE 0x62000000 /* V360EPC registers */ |
| |
| #define PCI_ENET0_IOADDR (CPU_PCI_IO_ADRS) |
| #define PCI_ENET0_MEMADDR (PCI_MEM_BASE) |
| |
| |
| #define V3_PCI_VENDOR 0x00000000 |
| #define V3_PCI_DEVICE 0x00000002 |
| #define V3_PCI_CMD 0x00000004 |
| #define V3_PCI_STAT 0x00000006 |
| #define V3_PCI_CC_REV 0x00000008 |
| #define V3_PCI_HDR_CF 0x0000000C |
| #define V3_PCI_IO_BASE 0x00000010 |
| #define V3_PCI_BASE0 0x00000014 |
| #define V3_PCI_BASE1 0x00000018 |
| #define V3_PCI_SUB_VENDOR 0x0000002C |
| #define V3_PCI_SUB_ID 0x0000002E |
| #define V3_PCI_ROM 0x00000030 |
| #define V3_PCI_BPARAM 0x0000003C |
| #define V3_PCI_MAP0 0x00000040 |
| #define V3_PCI_MAP1 0x00000044 |
| #define V3_PCI_INT_STAT 0x00000048 |
| #define V3_PCI_INT_CFG 0x0000004C |
| #define V3_LB_BASE0 0x00000054 |
| #define V3_LB_BASE1 0x00000058 |
| #define V3_LB_MAP0 0x0000005E |
| #define V3_LB_MAP1 0x00000062 |
| #define V3_LB_BASE2 0x00000064 |
| #define V3_LB_MAP2 0x00000066 |
| #define V3_LB_SIZE 0x00000068 |
| #define V3_LB_IO_BASE 0x0000006E |
| #define V3_FIFO_CFG 0x00000070 |
| #define V3_FIFO_PRIORITY 0x00000072 |
| #define V3_FIFO_STAT 0x00000074 |
| #define V3_LB_ISTAT 0x00000076 |
| #define V3_LB_IMASK 0x00000077 |
| #define V3_SYSTEM 0x00000078 |
| #define V3_LB_CFG 0x0000007A |
| #define V3_PCI_CFG 0x0000007C |
| #define V3_DMA_PCI_ADR0 0x00000080 |
| #define V3_DMA_PCI_ADR1 0x00000090 |
| #define V3_DMA_LOCAL_ADR0 0x00000084 |
| #define V3_DMA_LOCAL_ADR1 0x00000094 |
| #define V3_DMA_LENGTH0 0x00000088 |
| #define V3_DMA_LENGTH1 0x00000098 |
| #define V3_DMA_CSR0 0x0000008B |
| #define V3_DMA_CSR1 0x0000009B |
| #define V3_DMA_CTLB_ADR0 0x0000008C |
| #define V3_DMA_CTLB_ADR1 0x0000009C |
| #define V3_DMA_DELAY 0x000000E0 |
| #define V3_MAIL_DATA 0x000000C0 |
| #define V3_PCI_MAIL_IEWR 0x000000D0 |
| #define V3_PCI_MAIL_IERD 0x000000D2 |
| #define V3_LB_MAIL_IEWR 0x000000D4 |
| #define V3_LB_MAIL_IERD 0x000000D6 |
| #define V3_MAIL_WR_STAT 0x000000D8 |
| #define V3_MAIL_RD_STAT 0x000000DA |
| #define V3_QBA_MAP 0x000000DC |
| |
| /* SYSTEM register bits */ |
| #define V3_SYSTEM_M_RST_OUT (1 << 15) |
| #define V3_SYSTEM_M_LOCK (1 << 14) |
| |
| /* PCI_CFG bits */ |
| #define V3_PCI_CFG_M_RETRY_EN (1 << 10) |
| #define V3_PCI_CFG_M_AD_LOW1 (1 << 9) |
| #define V3_PCI_CFG_M_AD_LOW0 (1 << 8) |
| |
| /* PCI MAP register bits (PCI -> Local bus) */ |
| #define V3_PCI_MAP_M_MAP_ADR 0xFFF00000 |
| #define V3_PCI_MAP_M_RD_POST_INH (1 << 15) |
| #define V3_PCI_MAP_M_ROM_SIZE (1 << 11 | 1 << 10) |
| #define V3_PCI_MAP_M_SWAP (1 << 9 | 1 << 8) |
| #define V3_PCI_MAP_M_ADR_SIZE 0x000000F0 |
| #define V3_PCI_MAP_M_REG_EN (1 << 1) |
| #define V3_PCI_MAP_M_ENABLE (1 << 0) |
| |
| /* 9 => 512M window size */ |
| #define V3_PCI_MAP_M_ADR_SIZE_512M 0x00000090 |
| |
| /* A => 1024M window size */ |
| #define V3_PCI_MAP_M_ADR_SIZE_1024M 0x000000A0 |
| |
| /* LB_BASE register bits (Local bus -> PCI) */ |
| #define V3_LB_BASE_M_MAP_ADR 0xFFF00000 |
| #define V3_LB_BASE_M_SWAP (1 << 8 | 1 << 9) |
| #define V3_LB_BASE_M_ADR_SIZE 0x000000F0 |
| #define V3_LB_BASE_M_PREFETCH (1 << 3) |
| #define V3_LB_BASE_M_ENABLE (1 << 0) |
| |
| /* PCI COMMAND REGISTER bits */ |
| #define V3_COMMAND_M_FBB_EN (1 << 9) |
| #define V3_COMMAND_M_SERR_EN (1 << 8) |
| #define V3_COMMAND_M_PAR_EN (1 << 6) |
| #define V3_COMMAND_M_MASTER_EN (1 << 2) |
| #define V3_COMMAND_M_MEM_EN (1 << 1) |
| #define V3_COMMAND_M_IO_EN (1 << 0) |
| |
| #define INTEGRATOR_SC_BASE 0x11000000 |
| #define INTEGRATOR_SC_PCIENABLE_OFFSET 0x18 |
| #define INTEGRATOR_SC_PCIENABLE \ |
| (INTEGRATOR_SC_BASE + INTEGRATOR_SC_PCIENABLE_OFFSET) |
| |
| /*----------------------------------------------------------------------- |
| * There are various dependencies on the core module (CM) fitted |
| * Users should refer to their CM user guide |
| * - when porting adjust u-boot/Makefile accordingly |
| * to define the necessary CONFIG_ s for the CM involved |
| * see e.g. integratorcp_CM926EJ-S_config |
| */ |
| #include "armcoremodule.h" |
| |
| #endif /* __CONFIG_H */ |