drivers/net/dc2114x.c - github/trini/u-boot - Gitiles

 /*
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #include <common.h>
 #include <malloc.h>
 #include <net.h>
 #include <netdev.h>
 #include <pci.h>

 #undef DEBUG_SROM
 #undef DEBUG_SROM2

 #undef UPDATE_SROM

 /* PCI Registers.
  */
 #define PCI_CFDA_PSM		0x43

 #define CFRV_RN		0x000000f0	/* Revision Number */

 #define WAKEUP		0x00		/* Power Saving Wakeup */
 #define SLEEP		0x80		/* Power Saving Sleep Mode */

 #define DC2114x_BRK	0x0020		/* CFRV break between DC21142 & DC21143 */

 /* Ethernet chip registers.
  */
 #define DE4X5_BMR	0x000		/* Bus Mode Register */
 #define DE4X5_TPD	0x008		/* Transmit Poll Demand Reg */
 #define DE4X5_RRBA	0x018		/* RX Ring Base Address Reg */
 #define DE4X5_TRBA	0x020		/* TX Ring Base Address Reg */
 #define DE4X5_STS	0x028		/* Status Register */
 #define DE4X5_OMR	0x030		/* Operation Mode Register */
 #define DE4X5_SICR	0x068		/* SIA Connectivity Register */
 #define DE4X5_APROM	0x048		/* Ethernet Address PROM */

 /* Register bits.
  */
 #define BMR_SWR		0x00000001	/* Software Reset */
 #define STS_TS		0x00700000	/* Transmit Process State */
 #define STS_RS		0x000e0000	/* Receive Process State */
 #define OMR_ST		0x00002000	/* Start/Stop Transmission Command */
 #define OMR_SR		0x00000002	/* Start/Stop Receive */
 #define OMR_PS		0x00040000	/* Port Select */
 #define OMR_SDP		0x02000000	/* SD Polarity - MUST BE ASSERTED */
 #define OMR_PM		0x00000080	/* Pass All Multicast */

 /* Descriptor bits.
  */
 #define R_OWN		0x80000000	/* Own Bit */
 #define RD_RER		0x02000000	/* Receive End Of Ring */
 #define RD_LS		0x00000100	/* Last Descriptor */
 #define RD_ES		0x00008000	/* Error Summary */
 #define TD_TER		0x02000000	/* Transmit End Of Ring */
 #define T_OWN		0x80000000	/* Own Bit */
 #define TD_LS		0x40000000	/* Last Segment */
 #define TD_FS		0x20000000	/* First Segment */
 #define TD_ES		0x00008000	/* Error Summary */
 #define TD_SET		0x08000000	/* Setup Packet */

 /* The EEPROM commands include the alway-set leading bit. */
 #define SROM_WRITE_CMD	5
 #define SROM_READ_CMD	6
 #define SROM_ERASE_CMD	7

 #define SROM_HWADD	    0x0014	/* Hardware Address offset in SROM */
 #define SROM_RD		0x00004000	/* Read from Boot ROM */
 #define EE_DATA_WRITE	      0x04	/* EEPROM chip data in. */
 #define EE_WRITE_0	    0x4801
 #define EE_WRITE_1	    0x4805
 #define EE_DATA_READ	      0x08	/* EEPROM chip data out. */
 #define SROM_SR		0x00000800	/* Select Serial ROM when set */

 #define DT_IN		0x00000004	/* Serial Data In */
 #define DT_CLK		0x00000002	/* Serial ROM Clock */
 #define DT_CS		0x00000001	/* Serial ROM Chip Select */

 #define POLL_DEMAND	1

 #ifdef CONFIG_TULIP_FIX_DAVICOM
 #define RESET_DM9102(dev) {\
     unsigned long i;\
     i=INL(dev, 0x0);\
     udelay(1000);\
     OUTL(dev, i | BMR_SWR, DE4X5_BMR);\
     udelay(1000);\
 }
 #else
 #define RESET_DE4X5(dev) {\
     int i;\
     i=INL(dev, DE4X5_BMR);\
     udelay(1000);\
     OUTL(dev, i | BMR_SWR, DE4X5_BMR);\
     udelay(1000);\
     OUTL(dev, i, DE4X5_BMR);\
     udelay(1000);\
     for (i=0;i<5;i++) {INL(dev, DE4X5_BMR); udelay(10000);}\
     udelay(1000);\
 }
 #endif

 #define START_DE4X5(dev) {\
     s32 omr; \
     omr = INL(dev, DE4X5_OMR);\
     omr |= OMR_ST | OMR_SR;\
     OUTL(dev, omr, DE4X5_OMR);		/* Enable the TX and/or RX */\
 }

 #define STOP_DE4X5(dev) {\
     s32 omr; \
     omr = INL(dev, DE4X5_OMR);\
     omr &= ~(OMR_ST|OMR_SR);\
     OUTL(dev, omr, DE4X5_OMR);		/* Disable the TX and/or RX */ \
 }

 #define NUM_RX_DESC PKTBUFSRX
 #ifndef CONFIG_TULIP_FIX_DAVICOM
 	#define NUM_TX_DESC 1			/* Number of TX descriptors   */
 #else
 	#define NUM_TX_DESC 4
 #endif
 #define RX_BUFF_SZ  PKTSIZE_ALIGN

 #define TOUT_LOOP   1000000

 #define SETUP_FRAME_LEN 192
 #define ETH_ALEN	6

 struct de4x5_desc {
 	volatile s32 status;
 	u32 des1;
 	u32 buf;
 	u32 next;
 };

 static struct de4x5_desc rx_ring[NUM_RX_DESC] __attribute__ ((aligned(32))); /* RX descriptor ring         */
 static struct de4x5_desc tx_ring[NUM_TX_DESC] __attribute__ ((aligned(32))); /* TX descriptor ring         */
 static int rx_new;                             /* RX descriptor ring pointer */
 static int tx_new;                             /* TX descriptor ring pointer */

 static char rxRingSize;
 static char txRingSize;

 #if defined(UPDATE_SROM) || !defined(CONFIG_TULIP_FIX_DAVICOM)
 static void  sendto_srom(struct eth_device* dev, u_int command, u_long addr);
 static int   getfrom_srom(struct eth_device* dev, u_long addr);
 static int   do_eeprom_cmd(struct eth_device *dev, u_long ioaddr,int cmd,int cmd_len);
 static int   do_read_eeprom(struct eth_device *dev,u_long ioaddr,int location,int addr_len);
 #endif	/* UPDATE_SROM || !CONFIG_TULIP_FIX_DAVICOM */
 #ifdef UPDATE_SROM
 static int   write_srom(struct eth_device *dev, u_long ioaddr, int index, int new_value);
 static void  update_srom(struct eth_device *dev, bd_t *bis);
 #endif
 #ifndef CONFIG_TULIP_FIX_DAVICOM
 static int   read_srom(struct eth_device *dev, u_long ioaddr, int index);
 static void  read_hw_addr(struct eth_device* dev, bd_t * bis);
 #endif	/* CONFIG_TULIP_FIX_DAVICOM */
 static void  send_setup_frame(struct eth_device* dev, bd_t * bis);

 static int   dc21x4x_init(struct eth_device* dev, bd_t* bis);
 static int   dc21x4x_send(struct eth_device *dev, void *packet, int length);
 static int   dc21x4x_recv(struct eth_device* dev);
 static void  dc21x4x_halt(struct eth_device* dev);
 #ifdef CONFIG_TULIP_SELECT_MEDIA
 extern void  dc21x4x_select_media(struct eth_device* dev);
 #endif

 #if defined(CONFIG_E500)
 #define phys_to_bus(a) (a)
 #else
 #define phys_to_bus(a)	pci_phys_to_mem((pci_dev_t)dev->priv, a)
 #endif

 static int INL(struct eth_device* dev, u_long addr)
 {
 	return le32_to_cpu(*(volatile u_long *)(addr + dev->iobase));
 }

 static void OUTL(struct eth_device* dev, int command, u_long addr)
 {
 	*(volatile u_long *)(addr + dev->iobase) = cpu_to_le32(command);
 }

 static struct pci_device_id supported[] = {
 	{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP_FAST },
 	{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142 },
 #ifdef CONFIG_TULIP_FIX_DAVICOM
 	{ PCI_VENDOR_ID_DAVICOM, PCI_DEVICE_ID_DAVICOM_DM9102A },
 #endif
 	{ }
 };

 int dc21x4x_initialize(bd_t *bis)
 {
 	int			idx=0;
 	int			card_number = 0;
 	unsigned int		cfrv;
 	unsigned char		timer;
 	pci_dev_t		devbusfn;
 	unsigned int		iobase;
 	unsigned short		status;
 	struct eth_device*	dev;

 	while(1) {
 		devbusfn =  pci_find_devices(supported, idx++);
 		if (devbusfn == -1) {
 			break;
 		}

 		/* Get the chip configuration revision register. */
 		pci_read_config_dword(devbusfn, PCI_REVISION_ID, &cfrv);

 #ifndef CONFIG_TULIP_FIX_DAVICOM
 		if ((cfrv & CFRV_RN) < DC2114x_BRK ) {
 			printf("Error: The chip is not DC21143.\n");
 			continue;
 		}
 #endif

 		pci_read_config_word(devbusfn, PCI_COMMAND, &status);
 		status |=
 #ifdef CONFIG_TULIP_USE_IO
 		  PCI_COMMAND_IO |
 #else
 		  PCI_COMMAND_MEMORY |
 #endif
 		  PCI_COMMAND_MASTER;
 		pci_write_config_word(devbusfn, PCI_COMMAND, status);

 		pci_read_config_word(devbusfn, PCI_COMMAND, &status);
 #ifdef CONFIG_TULIP_USE_IO
 		if (!(status & PCI_COMMAND_IO)) {
 			printf("Error: Can not enable I/O access.\n");
 			continue;
 		}
 #else
 		if (!(status & PCI_COMMAND_MEMORY)) {
 			printf("Error: Can not enable MEMORY access.\n");
 			continue;
 		}
 #endif

 		if (!(status & PCI_COMMAND_MASTER)) {
 			printf("Error: Can not enable Bus Mastering.\n");
 			continue;
 		}

 		/* Check the latency timer for values >= 0x60. */
 		pci_read_config_byte(devbusfn, PCI_LATENCY_TIMER, &timer);

 		if (timer < 0x60) {
 			pci_write_config_byte(devbusfn, PCI_LATENCY_TIMER, 0x60);
 		}

 #ifdef CONFIG_TULIP_USE_IO
 		/* read BAR for memory space access */
 		pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0, &iobase);
 		iobase &= PCI_BASE_ADDRESS_IO_MASK;
 #else
 		/* read BAR for memory space access */
 		pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_1, &iobase);
 		iobase &= PCI_BASE_ADDRESS_MEM_MASK;
 #endif
 		debug ("dc21x4x: DEC 21142 PCI Device @0x%x\n", iobase);

 		dev = (struct eth_device*) malloc(sizeof *dev);

 		if (!dev) {
 			printf("Can not allocalte memory of dc21x4x\n");
 			break;
 		}
 		memset(dev, 0, sizeof(*dev));

 #ifdef CONFIG_TULIP_FIX_DAVICOM
 		sprintf(dev->name, "Davicom#%d", card_number);
 #else
 		sprintf(dev->name, "dc21x4x#%d", card_number);
 #endif

 #ifdef CONFIG_TULIP_USE_IO
 		dev->iobase = pci_io_to_phys(devbusfn, iobase);
 #else
 		dev->iobase = pci_mem_to_phys(devbusfn, iobase);
 #endif
 		dev->priv   = (void*) devbusfn;
 		dev->init   = dc21x4x_init;
 		dev->halt   = dc21x4x_halt;
 		dev->send   = dc21x4x_send;
 		dev->recv   = dc21x4x_recv;

 		/* Ensure we're not sleeping. */
 		pci_write_config_byte(devbusfn, PCI_CFDA_PSM, WAKEUP);

 		udelay(10 * 1000);

 #ifndef CONFIG_TULIP_FIX_DAVICOM
 		read_hw_addr(dev, bis);
 #endif
 		eth_register(dev);

 		card_number++;
 	}

 	return card_number;
 }

 static int dc21x4x_init(struct eth_device* dev, bd_t* bis)
 {
 	int		i;
 	int		devbusfn = (int) dev->priv;

 	/* Ensure we're not sleeping. */
 	pci_write_config_byte(devbusfn, PCI_CFDA_PSM, WAKEUP);

 #ifdef CONFIG_TULIP_FIX_DAVICOM
 	RESET_DM9102(dev);
 #else
 	RESET_DE4X5(dev);
 #endif

 	if ((INL(dev, DE4X5_STS) & (STS_TS | STS_RS)) != 0) {
 		printf("Error: Cannot reset ethernet controller.\n");
 		return -1;
 	}

 #ifdef CONFIG_TULIP_SELECT_MEDIA
 	dc21x4x_select_media(dev);
 #else
 	OUTL(dev, OMR_SDP | OMR_PS | OMR_PM, DE4X5_OMR);
 #endif

 	for (i = 0; i < NUM_RX_DESC; i++) {
 		rx_ring[i].status = cpu_to_le32(R_OWN);
 		rx_ring[i].des1 = cpu_to_le32(RX_BUFF_SZ);
 		rx_ring[i].buf = cpu_to_le32(phys_to_bus((u32) NetRxPackets[i]));
 #ifdef CONFIG_TULIP_FIX_DAVICOM
 		rx_ring[i].next = cpu_to_le32(phys_to_bus((u32) &rx_ring[(i+1) % NUM_RX_DESC]));
 #else
 		rx_ring[i].next = 0;
 #endif
 	}

 	for (i=0; i < NUM_TX_DESC; i++) {
 		tx_ring[i].status = 0;
 		tx_ring[i].des1 = 0;
 		tx_ring[i].buf = 0;

 #ifdef CONFIG_TULIP_FIX_DAVICOM
 	tx_ring[i].next = cpu_to_le32(phys_to_bus((u32) &tx_ring[(i+1) % NUM_TX_DESC]));
 #else
 		tx_ring[i].next = 0;
 #endif
 	}

 	rxRingSize = NUM_RX_DESC;
 	txRingSize = NUM_TX_DESC;

 	/* Write the end of list marker to the descriptor lists. */
 	rx_ring[rxRingSize - 1].des1 |= cpu_to_le32(RD_RER);
 	tx_ring[txRingSize - 1].des1 |= cpu_to_le32(TD_TER);

 	/* Tell the adapter where the TX/RX rings are located. */
 	OUTL(dev, phys_to_bus((u32) &rx_ring), DE4X5_RRBA);
 	OUTL(dev, phys_to_bus((u32) &tx_ring), DE4X5_TRBA);

 	START_DE4X5(dev);

 	tx_new = 0;
 	rx_new = 0;

 	send_setup_frame(dev, bis);

 	return 0;
 }

 static int dc21x4x_send(struct eth_device *dev, void *packet, int length)
 {
 	int		status = -1;
 	int		i;

 	if (length <= 0) {
 		printf("%s: bad packet size: %d\n", dev->name, length);
 		goto Done;
 	}

 	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
 		if (i >= TOUT_LOOP) {
 			printf("%s: tx error buffer not ready\n", dev->name);
 			goto Done;
 		}
 	}

 	tx_ring[tx_new].buf    = cpu_to_le32(phys_to_bus((u32) packet));
 	tx_ring[tx_new].des1   = cpu_to_le32(TD_TER | TD_LS | TD_FS | length);
 	tx_ring[tx_new].status = cpu_to_le32(T_OWN);

 	OUTL(dev, POLL_DEMAND, DE4X5_TPD);

 	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
 		if (i >= TOUT_LOOP) {
 			printf(".%s: tx buffer not ready\n", dev->name);
 			goto Done;
 		}
 	}

 	if (le32_to_cpu(tx_ring[tx_new].status) & TD_ES) {
 #if 0 /* test-only */
 		printf("TX error status = 0x%08X\n",
 			le32_to_cpu(tx_ring[tx_new].status));
 #endif
 		tx_ring[tx_new].status = 0x0;
 		goto Done;
 	}

 	status = length;

  Done:
     tx_new = (tx_new+1) % NUM_TX_DESC;
 	return status;
 }

 static int dc21x4x_recv(struct eth_device* dev)
 {
 	s32		status;
 	int		length    = 0;

 	for ( ; ; ) {
 		status = (s32)le32_to_cpu(rx_ring[rx_new].status);

 		if (status & R_OWN) {
 			break;
 		}

 		if (status & RD_LS) {
 			/* Valid frame status.
 			 */
 			if (status & RD_ES) {

 				/* There was an error.
 				 */
 				printf("RX error status = 0x%08X\n", status);
 			} else {
 				/* A valid frame received.
 				 */
 				length = (le32_to_cpu(rx_ring[rx_new].status) >> 16);

 				/* Pass the packet up to the protocol
 				 * layers.
 				 */
 				NetReceive(NetRxPackets[rx_new], length - 4);
 			}

 			/* Change buffer ownership for this frame, back
 			 * to the adapter.
 			 */
 			rx_ring[rx_new].status = cpu_to_le32(R_OWN);
 		}

 		/* Update entry information.
 		 */
 		rx_new = (rx_new + 1) % rxRingSize;
 	}

 	return length;
 }

 static void dc21x4x_halt(struct eth_device* dev)
 {
 	int		devbusfn = (int) dev->priv;

 	STOP_DE4X5(dev);
 	OUTL(dev, 0, DE4X5_SICR);

 	pci_write_config_byte(devbusfn, PCI_CFDA_PSM, SLEEP);
 }

 static void send_setup_frame(struct eth_device* dev, bd_t *bis)
 {
 	int		i;
 	char	setup_frame[SETUP_FRAME_LEN];
 	char	*pa = &setup_frame[0];

 	memset(pa, 0xff, SETUP_FRAME_LEN);

 	for (i = 0; i < ETH_ALEN; i++) {
 		*(pa + (i & 1)) = dev->enetaddr[i];
 		if (i & 0x01) {
 			pa += 4;
 		}
 	}

 	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
 		if (i >= TOUT_LOOP) {
 			printf("%s: tx error buffer not ready\n", dev->name);
 			goto Done;
 		}
 	}

 	tx_ring[tx_new].buf = cpu_to_le32(phys_to_bus((u32) &setup_frame[0]));
 	tx_ring[tx_new].des1 = cpu_to_le32(TD_TER | TD_SET| SETUP_FRAME_LEN);
 	tx_ring[tx_new].status = cpu_to_le32(T_OWN);

 	OUTL(dev, POLL_DEMAND, DE4X5_TPD);

 	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
 		if (i >= TOUT_LOOP) {
 			printf("%s: tx buffer not ready\n", dev->name);
 			goto Done;
 		}
 	}

 	if (le32_to_cpu(tx_ring[tx_new].status) != 0x7FFFFFFF) {
 		printf("TX error status2 = 0x%08X\n", le32_to_cpu(tx_ring[tx_new].status));
 	}
 	tx_new = (tx_new+1) % NUM_TX_DESC;

 Done:
 	return;
 }

 #if defined(UPDATE_SROM) || !defined(CONFIG_TULIP_FIX_DAVICOM)
 /* SROM Read and write routines.
  */
 static void
 sendto_srom(struct eth_device* dev, u_int command, u_long addr)
 {
 	OUTL(dev, command, addr);
 	udelay(1);
 }

 static int
 getfrom_srom(struct eth_device* dev, u_long addr)
 {
 	s32 tmp;

 	tmp = INL(dev, addr);
 	udelay(1);

 	return tmp;
 }

 /* Note: this routine returns extra data bits for size detection. */
 static int do_read_eeprom(struct eth_device *dev, u_long ioaddr, int location, int addr_len)
 {
 	int i;
 	unsigned retval = 0;
 	int read_cmd = location | (SROM_READ_CMD << addr_len);

 	sendto_srom(dev, SROM_RD | SROM_SR, ioaddr);
 	sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);

 #ifdef DEBUG_SROM
 	printf(" EEPROM read at %d ", location);
 #endif

 	/* Shift the read command bits out. */
 	for (i = 4 + addr_len; i >= 0; i--) {
 		short dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
 		sendto_srom(dev, SROM_RD | SROM_SR | DT_CS | dataval, ioaddr);
 		udelay(10);
 		sendto_srom(dev, SROM_RD | SROM_SR | DT_CS | dataval | DT_CLK, ioaddr);
 		udelay(10);
 #ifdef DEBUG_SROM2
 		printf("%X", getfrom_srom(dev, ioaddr) & 15);
 #endif
 		retval = (retval << 1) | ((getfrom_srom(dev, ioaddr) & EE_DATA_READ) ? 1 : 0);
 	}

 	sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);

 #ifdef DEBUG_SROM2
 	printf(" :%X:", getfrom_srom(dev, ioaddr) & 15);
 #endif

 	for (i = 16; i > 0; i--) {
 		sendto_srom(dev, SROM_RD | SROM_SR | DT_CS | DT_CLK, ioaddr);
 		udelay(10);
 #ifdef DEBUG_SROM2
 		printf("%X", getfrom_srom(dev, ioaddr) & 15);
 #endif
 		retval = (retval << 1) | ((getfrom_srom(dev, ioaddr) & EE_DATA_READ) ? 1 : 0);
 		sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);
 		udelay(10);
 	}

 	/* Terminate the EEPROM access. */
 	sendto_srom(dev, SROM_RD | SROM_SR, ioaddr);

 #ifdef DEBUG_SROM2
 	printf(" EEPROM value at %d is %5.5x.\n", location, retval);
 #endif

 	return retval;
 }
 #endif	/* UPDATE_SROM || !CONFIG_TULIP_FIX_DAVICOM */

 /* This executes a generic EEPROM command, typically a write or write
  * enable. It returns the data output from the EEPROM, and thus may
  * also be used for reads.
  */
 #if defined(UPDATE_SROM) || !defined(CONFIG_TULIP_FIX_DAVICOM)
 static int do_eeprom_cmd(struct eth_device *dev, u_long ioaddr, int cmd, int cmd_len)
 {
 	unsigned retval = 0;

 #ifdef DEBUG_SROM
 	printf(" EEPROM op 0x%x: ", cmd);
 #endif

 	sendto_srom(dev,SROM_RD | SROM_SR | DT_CS | DT_CLK, ioaddr);

 	/* Shift the command bits out. */
 	do {
 		short dataval = (cmd & (1 << cmd_len)) ? EE_WRITE_1 : EE_WRITE_0;
 		sendto_srom(dev,dataval, ioaddr);
 		udelay(10);

 #ifdef DEBUG_SROM2
 		printf("%X", getfrom_srom(dev,ioaddr) & 15);
 #endif

 		sendto_srom(dev,dataval | DT_CLK, ioaddr);
 		udelay(10);
 		retval = (retval << 1) | ((getfrom_srom(dev,ioaddr) & EE_DATA_READ) ? 1 : 0);
 	} while (--cmd_len >= 0);
 	sendto_srom(dev,SROM_RD | SROM_SR | DT_CS, ioaddr);

 	/* Terminate the EEPROM access. */
 	sendto_srom(dev,SROM_RD | SROM_SR, ioaddr);

 #ifdef DEBUG_SROM
 	printf(" EEPROM result is 0x%5.5x.\n", retval);
 #endif

 	return retval;
 }
 #endif	/* UPDATE_SROM || !CONFIG_TULIP_FIX_DAVICOM */

 #ifndef CONFIG_TULIP_FIX_DAVICOM
 static int read_srom(struct eth_device *dev, u_long ioaddr, int index)
 {
 	int ee_addr_size = do_read_eeprom(dev, ioaddr, 0xff, 8) & 0x40000 ? 8 : 6;

 	return do_eeprom_cmd(dev, ioaddr,
 			     (((SROM_READ_CMD << ee_addr_size) | index) << 16)
 			     | 0xffff, 3 + ee_addr_size + 16);
 }
 #endif	/* CONFIG_TULIP_FIX_DAVICOM */

 #ifdef UPDATE_SROM
 static int write_srom(struct eth_device *dev, u_long ioaddr, int index, int new_value)
 {
 	int ee_addr_size = do_read_eeprom(dev, ioaddr, 0xff, 8) & 0x40000 ? 8 : 6;
 	int i;
 	unsigned short newval;

 	udelay(10*1000); /* test-only */

 #ifdef DEBUG_SROM
 	printf("ee_addr_size=%d.\n", ee_addr_size);
 	printf("Writing new entry 0x%4.4x to offset %d.\n", new_value, index);
 #endif

 	/* Enable programming modes. */
 	do_eeprom_cmd(dev, ioaddr, (0x4f << (ee_addr_size-4)), 3+ee_addr_size);

 	/* Do the actual write. */
 	do_eeprom_cmd(dev, ioaddr,
 		      (((SROM_WRITE_CMD<<ee_addr_size)|index) << 16) | new_value,
 		      3 + ee_addr_size + 16);

 	/* Poll for write finished. */
 	sendto_srom(dev, SROM_RD | SROM_SR | DT_CS, ioaddr);
 	for (i = 0; i < 10000; i++)			/* Typical 2000 ticks */
 		if (getfrom_srom(dev, ioaddr) & EE_DATA_READ)
 			break;

 #ifdef DEBUG_SROM
 	printf(" Write finished after %d ticks.\n", i);
 #endif

 	/* Disable programming. */
 	do_eeprom_cmd(dev, ioaddr, (0x40 << (ee_addr_size-4)), 3 + ee_addr_size);

 	/* And read the result. */
 	newval = do_eeprom_cmd(dev, ioaddr,
 			       (((SROM_READ_CMD<<ee_addr_size)|index) << 16)
 			       | 0xffff, 3 + ee_addr_size + 16);
 #ifdef DEBUG_SROM
 	printf("  New value at offset %d is %4.4x.\n", index, newval);
 #endif
 	return 1;
 }
 #endif

 #ifndef CONFIG_TULIP_FIX_DAVICOM
 static void read_hw_addr(struct eth_device *dev, bd_t *bis)
 {
 	u_short tmp, *p = (u_short *)(&dev->enetaddr[0]);
 	int i, j = 0;

 	for (i = 0; i < (ETH_ALEN >> 1); i++) {
 		tmp = read_srom(dev, DE4X5_APROM, ((SROM_HWADD >> 1) + i));
 		*p = le16_to_cpu(tmp);
 		j += *p++;
 	}

 	if ((j == 0) || (j == 0x2fffd)) {
 		memset (dev->enetaddr, 0, ETH_ALEN);
 		debug ("Warning: can't read HW address from SROM.\n");
 		goto Done;
 	}

 	return;

 Done:
 #ifdef UPDATE_SROM
 	update_srom(dev, bis);
 #endif
 	return;
 }
 #endif	/* CONFIG_TULIP_FIX_DAVICOM */

 #ifdef UPDATE_SROM
 static void update_srom(struct eth_device *dev, bd_t *bis)
 {
 	int i;
 	static unsigned short eeprom[0x40] = {
 		0x140b, 0x6610, 0x0000, 0x0000,	/* 00 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 04 */
 		0x00a3, 0x0103, 0x0000, 0x0000,	/* 08 */
 		0x0000, 0x1f00, 0x0000, 0x0000,	/* 0c */
 		0x0108, 0x038d, 0x0000, 0x0000,	/* 10 */
 		0xe078, 0x0001, 0x0040, 0x0018,	/* 14 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 18 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 1c */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 20 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 24 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 28 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 2c */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 30 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 34 */
 		0x0000, 0x0000, 0x0000, 0x0000,	/* 38 */
 		0x0000, 0x0000, 0x0000, 0x4e07,	/* 3c */
 	};
 	uchar enetaddr[6];

 	/* Ethernet Addr... */
 	if (!eth_getenv_enetaddr("ethaddr", enetaddr))
 		return;
 	eeprom[0x0a] = (enetaddr[1] << 8) | enetaddr[0];
 	eeprom[0x0b] = (enetaddr[3] << 8) | enetaddr[2];
 	eeprom[0x0c] = (enetaddr[5] << 8) | enetaddr[4];

 	for (i=0; i<0x40; i++) {
 		write_srom(dev, DE4X5_APROM, i, eeprom[i]);
 	}
 }
 #endif	/* UPDATE_SROM */
	/*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#include <common.h>
	#include <malloc.h>
	#include <net.h>
	#include <netdev.h>
	#include <pci.h>

	#undef DEBUG_SROM
	#undef DEBUG_SROM2

	#undef UPDATE_SROM

	/* PCI Registers.
	*/
	#define PCI_CFDA_PSM 0x43

	#define CFRV_RN 0x000000f0 /* Revision Number */

	#define WAKEUP 0x00 /* Power Saving Wakeup */
	#define SLEEP 0x80 /* Power Saving Sleep Mode */

	#define DC2114x_BRK 0x0020 /* CFRV break between DC21142 & DC21143 */

	/* Ethernet chip registers.
	*/
	#define DE4X5_BMR 0x000 /* Bus Mode Register */
	#define DE4X5_TPD 0x008 /* Transmit Poll Demand Reg */
	#define DE4X5_RRBA 0x018 /* RX Ring Base Address Reg */
	#define DE4X5_TRBA 0x020 /* TX Ring Base Address Reg */
	#define DE4X5_STS 0x028 /* Status Register */
	#define DE4X5_OMR 0x030 /* Operation Mode Register */
	#define DE4X5_SICR 0x068 /* SIA Connectivity Register */
	#define DE4X5_APROM 0x048 /* Ethernet Address PROM */

	/* Register bits.
	*/
	#define BMR_SWR 0x00000001 /* Software Reset */
	#define STS_TS 0x00700000 /* Transmit Process State */
	#define STS_RS 0x000e0000 /* Receive Process State */
	#define OMR_ST 0x00002000 /* Start/Stop Transmission Command */
	#define OMR_SR 0x00000002 /* Start/Stop Receive */
	#define OMR_PS 0x00040000 /* Port Select */
	#define OMR_SDP 0x02000000 /* SD Polarity - MUST BE ASSERTED */
	#define OMR_PM 0x00000080 /* Pass All Multicast */

	/* Descriptor bits.
	*/
	#define R_OWN 0x80000000 /* Own Bit */
	#define RD_RER 0x02000000 /* Receive End Of Ring */
	#define RD_LS 0x00000100 /* Last Descriptor */
	#define RD_ES 0x00008000 /* Error Summary */
	#define TD_TER 0x02000000 /* Transmit End Of Ring */
	#define T_OWN 0x80000000 /* Own Bit */
	#define TD_LS 0x40000000 /* Last Segment */
	#define TD_FS 0x20000000 /* First Segment */
	#define TD_ES 0x00008000 /* Error Summary */
	#define TD_SET 0x08000000 /* Setup Packet */

	/* The EEPROM commands include the alway-set leading bit. */
	#define SROM_WRITE_CMD 5
	#define SROM_READ_CMD 6
	#define SROM_ERASE_CMD 7

	#define SROM_HWADD 0x0014 /* Hardware Address offset in SROM */
	#define SROM_RD 0x00004000 /* Read from Boot ROM */
	#define EE_DATA_WRITE 0x04 /* EEPROM chip data in. */
	#define EE_WRITE_0 0x4801
	#define EE_WRITE_1 0x4805
	#define EE_DATA_READ 0x08 /* EEPROM chip data out. */
	#define SROM_SR 0x00000800 /* Select Serial ROM when set */

	#define DT_IN 0x00000004 /* Serial Data In */
	#define DT_CLK 0x00000002 /* Serial ROM Clock */
	#define DT_CS 0x00000001 /* Serial ROM Chip Select */

	#define POLL_DEMAND 1

	#ifdef CONFIG_TULIP_FIX_DAVICOM
	#define RESET_DM9102(dev) {\
	unsigned long i;\
	i=INL(dev, 0x0);\
	udelay(1000);\
	OUTL(dev, i \| BMR_SWR, DE4X5_BMR);\
	udelay(1000);\
	}
	#else
	#define RESET_DE4X5(dev) {\
	int i;\
	i=INL(dev, DE4X5_BMR);\
	udelay(1000);\
	OUTL(dev, i \| BMR_SWR, DE4X5_BMR);\
	udelay(1000);\
	OUTL(dev, i, DE4X5_BMR);\
	udelay(1000);\
	for (i=0;i<5;i++) {INL(dev, DE4X5_BMR); udelay(10000);}\
	udelay(1000);\
	}
	#endif

	#define START_DE4X5(dev) {\
	s32 omr; \
	omr = INL(dev, DE4X5_OMR);\
	omr \|= OMR_ST \| OMR_SR;\
	OUTL(dev, omr, DE4X5_OMR); /* Enable the TX and/or RX */\
	}

	#define STOP_DE4X5(dev) {\
	s32 omr; \
	omr = INL(dev, DE4X5_OMR);\
	omr &= ~(OMR_ST\|OMR_SR);\
	OUTL(dev, omr, DE4X5_OMR); /* Disable the TX and/or RX */ \
	}

	#define NUM_RX_DESC PKTBUFSRX
	#ifndef CONFIG_TULIP_FIX_DAVICOM
	#define NUM_TX_DESC 1 /* Number of TX descriptors */
	#else
	#define NUM_TX_DESC 4
	#endif
	#define RX_BUFF_SZ PKTSIZE_ALIGN

	#define TOUT_LOOP 1000000

	#define SETUP_FRAME_LEN 192
	#define ETH_ALEN 6

	struct de4x5_desc {
	volatile s32 status;
	u32 des1;
	u32 buf;
	u32 next;
	};

	static struct de4x5_desc rx_ring[NUM_RX_DESC] __attribute__ ((aligned(32))); /* RX descriptor ring */
	static struct de4x5_desc tx_ring[NUM_TX_DESC] __attribute__ ((aligned(32))); /* TX descriptor ring */
	static int rx_new; /* RX descriptor ring pointer */
	static int tx_new; /* TX descriptor ring pointer */

	static char rxRingSize;
	static char txRingSize;

	#if defined(UPDATE_SROM) \|\| !defined(CONFIG_TULIP_FIX_DAVICOM)
	static void sendto_srom(struct eth_device* dev, u_int command, u_long addr);
	static int getfrom_srom(struct eth_device* dev, u_long addr);
	static int do_eeprom_cmd(struct eth_device *dev, u_long ioaddr,int cmd,int cmd_len);
	static int do_read_eeprom(struct eth_device *dev,u_long ioaddr,int location,int addr_len);
	#endif /* UPDATE_SROM \|\| !CONFIG_TULIP_FIX_DAVICOM */
	#ifdef UPDATE_SROM
	static int write_srom(struct eth_device *dev, u_long ioaddr, int index, int new_value);
	static void update_srom(struct eth_device dev, bd_t bis);
	#endif
	#ifndef CONFIG_TULIP_FIX_DAVICOM
	static int read_srom(struct eth_device *dev, u_long ioaddr, int index);
	static void read_hw_addr(struct eth_device* dev, bd_t * bis);
	#endif /* CONFIG_TULIP_FIX_DAVICOM */
	static void send_setup_frame(struct eth_device* dev, bd_t * bis);

	static int dc21x4x_init(struct eth_device* dev, bd_t* bis);
	static int dc21x4x_send(struct eth_device dev, void packet, int length);
	static int dc21x4x_recv(struct eth_device* dev);
	static void dc21x4x_halt(struct eth_device* dev);
	#ifdef CONFIG_TULIP_SELECT_MEDIA
	extern void dc21x4x_select_media(struct eth_device* dev);
	#endif

	#if defined(CONFIG_E500)
	#define phys_to_bus(a) (a)
	#else
	#define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a)
	#endif

	static int INL(struct eth_device* dev, u_long addr)
	{
	return le32_to_cpu((volatile u_long )(addr + dev->iobase));
	}

	static void OUTL(struct eth_device* dev, int command, u_long addr)
	{
	(volatile u_long )(addr + dev->iobase) = cpu_to_le32(command);
	}

	static struct pci_device_id supported[] = {
	{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_TULIP_FAST },
	{ PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142 },
	#ifdef CONFIG_TULIP_FIX_DAVICOM
	{ PCI_VENDOR_ID_DAVICOM, PCI_DEVICE_ID_DAVICOM_DM9102A },
	#endif
	{ }
	};

	int dc21x4x_initialize(bd_t *bis)
	{
	int idx=0;
	int card_number = 0;
	unsigned int cfrv;
	unsigned char timer;
	pci_dev_t devbusfn;
	unsigned int iobase;
	unsigned short status;
	struct eth_device* dev;

	while(1) {
	devbusfn = pci_find_devices(supported, idx++);
	if (devbusfn == -1) {
	break;
	}

	/* Get the chip configuration revision register. */
	pci_read_config_dword(devbusfn, PCI_REVISION_ID, &cfrv);

	#ifndef CONFIG_TULIP_FIX_DAVICOM
	if ((cfrv & CFRV_RN) < DC2114x_BRK ) {
	printf("Error: The chip is not DC21143.\n");
	continue;
	}
	#endif

	pci_read_config_word(devbusfn, PCI_COMMAND, &status);
	status \|=
	#ifdef CONFIG_TULIP_USE_IO
	PCI_COMMAND_IO \|
	#else
	PCI_COMMAND_MEMORY \|
	#endif
	PCI_COMMAND_MASTER;
	pci_write_config_word(devbusfn, PCI_COMMAND, status);

	pci_read_config_word(devbusfn, PCI_COMMAND, &status);
	#ifdef CONFIG_TULIP_USE_IO
	if (!(status & PCI_COMMAND_IO)) {
	printf("Error: Can not enable I/O access.\n");
	continue;
	}
	#else
	if (!(status & PCI_COMMAND_MEMORY)) {
	printf("Error: Can not enable MEMORY access.\n");
	continue;
	}
	#endif

	if (!(status & PCI_COMMAND_MASTER)) {
	printf("Error: Can not enable Bus Mastering.\n");
	continue;
	}

	/* Check the latency timer for values >= 0x60. */
	pci_read_config_byte(devbusfn, PCI_LATENCY_TIMER, &timer);

	if (timer < 0x60) {
	pci_write_config_byte(devbusfn, PCI_LATENCY_TIMER, 0x60);
	}

	#ifdef CONFIG_TULIP_USE_IO
	/* read BAR for memory space access */
	pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0, &iobase);
	iobase &= PCI_BASE_ADDRESS_IO_MASK;
	#else
	/* read BAR for memory space access */
	pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_1, &iobase);
	iobase &= PCI_BASE_ADDRESS_MEM_MASK;
	#endif
	debug ("dc21x4x: DEC 21142 PCI Device @0x%x\n", iobase);

	dev = (struct eth_device) malloc(sizeof dev);

	if (!dev) {
	printf("Can not allocalte memory of dc21x4x\n");
	break;
	}
	memset(dev, 0, sizeof(*dev));

	#ifdef CONFIG_TULIP_FIX_DAVICOM
	sprintf(dev->name, "Davicom#%d", card_number);
	#else
	sprintf(dev->name, "dc21x4x#%d", card_number);
	#endif

	#ifdef CONFIG_TULIP_USE_IO
	dev->iobase = pci_io_to_phys(devbusfn, iobase);
	#else
	dev->iobase = pci_mem_to_phys(devbusfn, iobase);
	#endif
	dev->priv = (void*) devbusfn;
	dev->init = dc21x4x_init;
	dev->halt = dc21x4x_halt;
	dev->send = dc21x4x_send;
	dev->recv = dc21x4x_recv;

	/* Ensure we're not sleeping. */
	pci_write_config_byte(devbusfn, PCI_CFDA_PSM, WAKEUP);

	udelay(10 * 1000);

	#ifndef CONFIG_TULIP_FIX_DAVICOM
	read_hw_addr(dev, bis);
	#endif
	eth_register(dev);

	card_number++;
	}

	return card_number;
	}

	static int dc21x4x_init(struct eth_device* dev, bd_t* bis)
	{
	int i;
	int devbusfn = (int) dev->priv;

	/* Ensure we're not sleeping. */
	pci_write_config_byte(devbusfn, PCI_CFDA_PSM, WAKEUP);

	#ifdef CONFIG_TULIP_FIX_DAVICOM
	RESET_DM9102(dev);
	#else
	RESET_DE4X5(dev);
	#endif

	if ((INL(dev, DE4X5_STS) & (STS_TS \| STS_RS)) != 0) {
	printf("Error: Cannot reset ethernet controller.\n");
	return -1;
	}

	#ifdef CONFIG_TULIP_SELECT_MEDIA
	dc21x4x_select_media(dev);
	#else
	OUTL(dev, OMR_SDP \| OMR_PS \| OMR_PM, DE4X5_OMR);
	#endif

	for (i = 0; i < NUM_RX_DESC; i++) {
	rx_ring[i].status = cpu_to_le32(R_OWN);
	rx_ring[i].des1 = cpu_to_le32(RX_BUFF_SZ);
	rx_ring[i].buf = cpu_to_le32(phys_to_bus((u32) NetRxPackets[i]));
	#ifdef CONFIG_TULIP_FIX_DAVICOM
	rx_ring[i].next = cpu_to_le32(phys_to_bus((u32) &rx_ring[(i+1) % NUM_RX_DESC]));
	#else
	rx_ring[i].next = 0;
	#endif
	}

	for (i=0; i < NUM_TX_DESC; i++) {
	tx_ring[i].status = 0;
	tx_ring[i].des1 = 0;
	tx_ring[i].buf = 0;

	#ifdef CONFIG_TULIP_FIX_DAVICOM
	tx_ring[i].next = cpu_to_le32(phys_to_bus((u32) &tx_ring[(i+1) % NUM_TX_DESC]));
	#else
	tx_ring[i].next = 0;
	#endif
	}

	rxRingSize = NUM_RX_DESC;
	txRingSize = NUM_TX_DESC;

	/* Write the end of list marker to the descriptor lists. */
	rx_ring[rxRingSize - 1].des1 \|= cpu_to_le32(RD_RER);
	tx_ring[txRingSize - 1].des1 \|= cpu_to_le32(TD_TER);

	/* Tell the adapter where the TX/RX rings are located. */
	OUTL(dev, phys_to_bus((u32) &rx_ring), DE4X5_RRBA);
	OUTL(dev, phys_to_bus((u32) &tx_ring), DE4X5_TRBA);

	START_DE4X5(dev);

	tx_new = 0;
	rx_new = 0;

	send_setup_frame(dev, bis);

	return 0;
	}

	static int dc21x4x_send(struct eth_device dev, void packet, int length)
	{
	int status = -1;
	int i;

	if (length <= 0) {
	printf("%s: bad packet size: %d\n", dev->name, length);
	goto Done;
	}

	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
	if (i >= TOUT_LOOP) {
	printf("%s: tx error buffer not ready\n", dev->name);
	goto Done;
	}
	}

	tx_ring[tx_new].buf = cpu_to_le32(phys_to_bus((u32) packet));
	tx_ring[tx_new].des1 = cpu_to_le32(TD_TER \| TD_LS \| TD_FS \| length);
	tx_ring[tx_new].status = cpu_to_le32(T_OWN);

	OUTL(dev, POLL_DEMAND, DE4X5_TPD);

	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
	if (i >= TOUT_LOOP) {
	printf(".%s: tx buffer not ready\n", dev->name);
	goto Done;
	}
	}

	if (le32_to_cpu(tx_ring[tx_new].status) & TD_ES) {
	#if 0 /* test-only */
	printf("TX error status = 0x%08X\n",
	le32_to_cpu(tx_ring[tx_new].status));
	#endif
	tx_ring[tx_new].status = 0x0;
	goto Done;
	}

	status = length;

	Done:
	tx_new = (tx_new+1) % NUM_TX_DESC;
	return status;
	}

	static int dc21x4x_recv(struct eth_device* dev)
	{
	s32 status;
	int length = 0;

	for ( ; ; ) {
	status = (s32)le32_to_cpu(rx_ring[rx_new].status);

	if (status & R_OWN) {
	break;
	}

	if (status & RD_LS) {
	/* Valid frame status.
	*/
	if (status & RD_ES) {

	/* There was an error.
	*/
	printf("RX error status = 0x%08X\n", status);
	} else {
	/* A valid frame received.
	*/
	length = (le32_to_cpu(rx_ring[rx_new].status) >> 16);

	/* Pass the packet up to the protocol
	* layers.
	*/
	NetReceive(NetRxPackets[rx_new], length - 4);
	}

	/* Change buffer ownership for this frame, back
	* to the adapter.
	*/
	rx_ring[rx_new].status = cpu_to_le32(R_OWN);
	}

	/* Update entry information.
	*/
	rx_new = (rx_new + 1) % rxRingSize;
	}

	return length;
	}

	static void dc21x4x_halt(struct eth_device* dev)
	{
	int devbusfn = (int) dev->priv;

	STOP_DE4X5(dev);
	OUTL(dev, 0, DE4X5_SICR);

	pci_write_config_byte(devbusfn, PCI_CFDA_PSM, SLEEP);
	}

	static void send_setup_frame(struct eth_device* dev, bd_t *bis)
	{
	int i;
	char setup_frame[SETUP_FRAME_LEN];
	char *pa = &setup_frame[0];

	memset(pa, 0xff, SETUP_FRAME_LEN);

	for (i = 0; i < ETH_ALEN; i++) {
	*(pa + (i & 1)) = dev->enetaddr[i];
	if (i & 0x01) {
	pa += 4;
	}
	}

	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
	if (i >= TOUT_LOOP) {
	printf("%s: tx error buffer not ready\n", dev->name);
	goto Done;
	}
	}

	tx_ring[tx_new].buf = cpu_to_le32(phys_to_bus((u32) &setup_frame[0]));
	tx_ring[tx_new].des1 = cpu_to_le32(TD_TER \| TD_SET\| SETUP_FRAME_LEN);
	tx_ring[tx_new].status = cpu_to_le32(T_OWN);

	OUTL(dev, POLL_DEMAND, DE4X5_TPD);

	for(i = 0; tx_ring[tx_new].status & cpu_to_le32(T_OWN); i++) {
	if (i >= TOUT_LOOP) {
	printf("%s: tx buffer not ready\n", dev->name);
	goto Done;
	}
	}

	if (le32_to_cpu(tx_ring[tx_new].status) != 0x7FFFFFFF) {
	printf("TX error status2 = 0x%08X\n", le32_to_cpu(tx_ring[tx_new].status));
	}
	tx_new = (tx_new+1) % NUM_TX_DESC;

	Done:
	return;
	}

	#if defined(UPDATE_SROM) \|\| !defined(CONFIG_TULIP_FIX_DAVICOM)
	/* SROM Read and write routines.
	*/
	static void
	sendto_srom(struct eth_device* dev, u_int command, u_long addr)
	{
	OUTL(dev, command, addr);
	udelay(1);
	}

	static int
	getfrom_srom(struct eth_device* dev, u_long addr)
	{
	s32 tmp;

	tmp = INL(dev, addr);
	udelay(1);

	return tmp;
	}

	/* Note: this routine returns extra data bits for size detection. */
	static int do_read_eeprom(struct eth_device *dev, u_long ioaddr, int location, int addr_len)
	{
	int i;
	unsigned retval = 0;
	int read_cmd = location \| (SROM_READ_CMD << addr_len);

	sendto_srom(dev, SROM_RD \| SROM_SR, ioaddr);
	sendto_srom(dev, SROM_RD \| SROM_SR \| DT_CS, ioaddr);

	#ifdef DEBUG_SROM
	printf(" EEPROM read at %d ", location);
	#endif

	/* Shift the read command bits out. */
	for (i = 4 + addr_len; i >= 0; i--) {
	short dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
	sendto_srom(dev, SROM_RD \| SROM_SR \| DT_CS \| dataval, ioaddr);
	udelay(10);
	sendto_srom(dev, SROM_RD \| SROM_SR \| DT_CS \| dataval \| DT_CLK, ioaddr);
	udelay(10);
	#ifdef DEBUG_SROM2
	printf("%X", getfrom_srom(dev, ioaddr) & 15);
	#endif
	retval = (retval << 1) \| ((getfrom_srom(dev, ioaddr) & EE_DATA_READ) ? 1 : 0);
	}

	sendto_srom(dev, SROM_RD \| SROM_SR \| DT_CS, ioaddr);

	#ifdef DEBUG_SROM2
	printf(" :%X:", getfrom_srom(dev, ioaddr) & 15);
	#endif

	for (i = 16; i > 0; i--) {
	sendto_srom(dev, SROM_RD \| SROM_SR \| DT_CS \| DT_CLK, ioaddr);
	udelay(10);
	#ifdef DEBUG_SROM2
	printf("%X", getfrom_srom(dev, ioaddr) & 15);
	#endif
	retval = (retval << 1) \| ((getfrom_srom(dev, ioaddr) & EE_DATA_READ) ? 1 : 0);
	sendto_srom(dev, SROM_RD \| SROM_SR \| DT_CS, ioaddr);
	udelay(10);
	}

	/* Terminate the EEPROM access. */
	sendto_srom(dev, SROM_RD \| SROM_SR, ioaddr);

	#ifdef DEBUG_SROM2
	printf(" EEPROM value at %d is %5.5x.\n", location, retval);
	#endif

	return retval;
	}
	#endif /* UPDATE_SROM \|\| !CONFIG_TULIP_FIX_DAVICOM */

	/* This executes a generic EEPROM command, typically a write or write
	* enable. It returns the data output from the EEPROM, and thus may
	* also be used for reads.
	*/
	#if defined(UPDATE_SROM) \|\| !defined(CONFIG_TULIP_FIX_DAVICOM)
	static int do_eeprom_cmd(struct eth_device *dev, u_long ioaddr, int cmd, int cmd_len)
	{
	unsigned retval = 0;

	#ifdef DEBUG_SROM
	printf(" EEPROM op 0x%x: ", cmd);
	#endif

	sendto_srom(dev,SROM_RD \| SROM_SR \| DT_CS \| DT_CLK, ioaddr);

	/* Shift the command bits out. */
	do {
	short dataval = (cmd & (1 << cmd_len)) ? EE_WRITE_1 : EE_WRITE_0;
	sendto_srom(dev,dataval, ioaddr);
	udelay(10);

	#ifdef DEBUG_SROM2
	printf("%X", getfrom_srom(dev,ioaddr) & 15);
	#endif

	sendto_srom(dev,dataval \| DT_CLK, ioaddr);
	udelay(10);
	retval = (retval << 1) \| ((getfrom_srom(dev,ioaddr) & EE_DATA_READ) ? 1 : 0);
	} while (--cmd_len >= 0);
	sendto_srom(dev,SROM_RD \| SROM_SR \| DT_CS, ioaddr);

	/* Terminate the EEPROM access. */
	sendto_srom(dev,SROM_RD \| SROM_SR, ioaddr);

	#ifdef DEBUG_SROM
	printf(" EEPROM result is 0x%5.5x.\n", retval);
	#endif

	return retval;
	}
	#endif /* UPDATE_SROM \|\| !CONFIG_TULIP_FIX_DAVICOM */

	#ifndef CONFIG_TULIP_FIX_DAVICOM
	static int read_srom(struct eth_device *dev, u_long ioaddr, int index)
	{
	int ee_addr_size = do_read_eeprom(dev, ioaddr, 0xff, 8) & 0x40000 ? 8 : 6;

	return do_eeprom_cmd(dev, ioaddr,
	(((SROM_READ_CMD << ee_addr_size) \| index) << 16)
	\| 0xffff, 3 + ee_addr_size + 16);
	}
	#endif /* CONFIG_TULIP_FIX_DAVICOM */

	#ifdef UPDATE_SROM
	static int write_srom(struct eth_device *dev, u_long ioaddr, int index, int new_value)
	{
	int ee_addr_size = do_read_eeprom(dev, ioaddr, 0xff, 8) & 0x40000 ? 8 : 6;
	int i;
	unsigned short newval;

	udelay(101000); / test-only */

	#ifdef DEBUG_SROM
	printf("ee_addr_size=%d.\n", ee_addr_size);
	printf("Writing new entry 0x%4.4x to offset %d.\n", new_value, index);
	#endif

	/* Enable programming modes. */
	do_eeprom_cmd(dev, ioaddr, (0x4f << (ee_addr_size-4)), 3+ee_addr_size);

	/* Do the actual write. */
	do_eeprom_cmd(dev, ioaddr,
	(((SROM_WRITE_CMD<<ee_addr_size)\|index) << 16) \| new_value,
	3 + ee_addr_size + 16);

	/* Poll for write finished. */
	sendto_srom(dev, SROM_RD \| SROM_SR \| DT_CS, ioaddr);
	for (i = 0; i < 10000; i++) /* Typical 2000 ticks */
	if (getfrom_srom(dev, ioaddr) & EE_DATA_READ)
	break;

	#ifdef DEBUG_SROM
	printf(" Write finished after %d ticks.\n", i);
	#endif

	/* Disable programming. */
	do_eeprom_cmd(dev, ioaddr, (0x40 << (ee_addr_size-4)), 3 + ee_addr_size);

	/* And read the result. */
	newval = do_eeprom_cmd(dev, ioaddr,
	(((SROM_READ_CMD<<ee_addr_size)\|index) << 16)
	\| 0xffff, 3 + ee_addr_size + 16);
	#ifdef DEBUG_SROM
	printf(" New value at offset %d is %4.4x.\n", index, newval);
	#endif
	return 1;
	}
	#endif

	#ifndef CONFIG_TULIP_FIX_DAVICOM
	static void read_hw_addr(struct eth_device dev, bd_t bis)
	{
	u_short tmp, p = (u_short )(&dev->enetaddr[0]);
	int i, j = 0;

	for (i = 0; i < (ETH_ALEN >> 1); i++) {
	tmp = read_srom(dev, DE4X5_APROM, ((SROM_HWADD >> 1) + i));
	*p = le16_to_cpu(tmp);
	j += *p++;
	}

	if ((j == 0) \|\| (j == 0x2fffd)) {
	memset (dev->enetaddr, 0, ETH_ALEN);
	debug ("Warning: can't read HW address from SROM.\n");
	goto Done;
	}

	return;

	Done:
	#ifdef UPDATE_SROM
	update_srom(dev, bis);
	#endif
	return;
	}
	#endif /* CONFIG_TULIP_FIX_DAVICOM */

	#ifdef UPDATE_SROM
	static void update_srom(struct eth_device dev, bd_t bis)
	{
	int i;
	static unsigned short eeprom[0x40] = {
	0x140b, 0x6610, 0x0000, 0x0000, /* 00 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 04 */
	0x00a3, 0x0103, 0x0000, 0x0000, /* 08 */
	0x0000, 0x1f00, 0x0000, 0x0000, /* 0c */
	0x0108, 0x038d, 0x0000, 0x0000, /* 10 */
	0xe078, 0x0001, 0x0040, 0x0018, /* 14 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 18 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 1c */
	0x0000, 0x0000, 0x0000, 0x0000, /* 20 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 24 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 28 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 2c */
	0x0000, 0x0000, 0x0000, 0x0000, /* 30 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 34 */
	0x0000, 0x0000, 0x0000, 0x0000, /* 38 */
	0x0000, 0x0000, 0x0000, 0x4e07, /* 3c */
	};
	uchar enetaddr[6];

	/* Ethernet Addr... */
	if (!eth_getenv_enetaddr("ethaddr", enetaddr))
	return;
	eeprom[0x0a] = (enetaddr[1] << 8) \| enetaddr[0];
	eeprom[0x0b] = (enetaddr[3] << 8) \| enetaddr[2];
	eeprom[0x0c] = (enetaddr[5] << 8) \| enetaddr[4];

	for (i=0; i<0x40; i++) {
	write_srom(dev, DE4X5_APROM, i, eeprom[i]);
	}
	}
	#endif /* UPDATE_SROM */