include/configs/katmai.h - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2007
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
  * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /************************************************************************
  * katmai.h - configuration for AMCC Katmai (440SPe)
  ***********************************************************************/

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*-----------------------------------------------------------------------
  * High Level Configuration Options
  *----------------------------------------------------------------------*/
 #define CONFIG_KATMAI			1	/* Board is Katmai	*/
 #define CONFIG_4xx			1	/* ... PPC4xx family	*/
 #define CONFIG_440			1	/* ... PPC440 family	*/
 #define CONFIG_440SPE			1	/* Specifc SPe support	*/
 #undef	CFG_DRAM_TEST				/* Disable-takes long time */
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/

 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
 #undef  CONFIG_SHOW_BOOT_PROGRESS

 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
 #define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xff000000	/* start of FLASH	*/
 #define CFG_PERIPHERAL_BASE	0xa0000000	/* internal peripherals	*/
 #define CFG_ISRAM_BASE		0x90000000	/* internal SRAM	*/

 #define CFG_PCI_MEMBASE		0x80000000	/* mapped PCI memory	*/
 #define CFG_PCI_BASE		0xd0000000	/* internal PCI regs	*/
 #define CFG_PCI_TARGBASE	CFG_PCI_MEMBASE

 #define CFG_PCIE_MEMBASE	0xb0000000	/* mapped PCIe memory	*/
 #define CFG_PCIE_MEMSIZE	0x08000000	/* smallest incr for PCIe port */
 #define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */

 #define CFG_PCIE0_CFGBASE	0xc0000000
 #define CFG_PCIE1_CFGBASE	0xc1000000
 #define CFG_PCIE2_CFGBASE	0xc2000000
 #define CFG_PCIE0_XCFGBASE	0xc3000000
 #define CFG_PCIE1_XCFGBASE	0xc3001000
 #define CFG_PCIE2_XCFGBASE	0xc3002000

 /* base address of inbound PCIe window */
 #define CFG_PCIE_INBOUND_BASE	0x0000000000000000ULL

 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
 #define CONFIG_PCI_SYS_MEM_PHYS	CFG_SDRAM_BASE
 #define CONFIG_PCI_SYS_MEM_SIZE	(1024 * 1024 * 1024)

 #define CFG_ACE_BASE		0xfe000000	/* Xilinx ACE controller - Compact Flash */

 #define CFG_MONITOR_BASE	TEXT_BASE
 #define CFG_MONITOR_LEN		(0xFFFFFFFF - CFG_MONITOR_BASE + 1)
 #define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc */

 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in internal SRAM)
  *----------------------------------------------------------------------*/
 #define CFG_TEMP_STACK_OCM	1
 #define CFG_OCM_DATA_ADDR	CFG_ISRAM_BASE
 #define CFG_INIT_RAM_ADDR	CFG_ISRAM_BASE	/* Initial RAM address	*/
 #define CFG_INIT_RAM_END	0x2000		/* End of used area in RAM */
 #define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */

 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR

 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CONFIG_SERIAL_MULTI	1
 #undef CONFIG_UART1_CONSOLE
 #undef CFG_EXT_SERIAL_CLOCK
 #define CONFIG_BAUDRATE		115200
 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
 #define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
 #define SPD_EEPROM_ADDRESS	{0x51, 0x52}	/* SPD i2c spd addresses*/
 #define CONFIG_DDR_ECC		1	/* with ECC support		*/
 #define CONFIG_DDR_RQDC_FIXED	0x80000038 /* optimal value found by GDA*/
 #undef  CONFIG_STRESS

 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		100000	/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F

 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CFG_SPD_BUS_NUM		0	/* The I2C bus for SPD		*/

 #define IIC0_BOOTPROM_ADDR	0x50
 #define IIC0_ALT_BOOTPROM_ADDR	0x54

 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0x50)
 #define CFG_I2C_EEPROM_ADDR_LEN 1
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10

 /* I2C RTC */
 #define CONFIG_RTC_M41T11	1
 #define CFG_RTC_BUS_NUM		1	/* The I2C bus for RTC		*/
 #define CFG_I2C_RTC_ADDR	0x68
 #define CFG_M41T11_BASE_YEAR	1900	/* play along with linux	*/

 /* I2C DTT */
 #define CONFIG_DTT_ADM1021	1	/* ADM1021 temp sensor support	*/
 #define CFG_DTT_BUS_NUM		1	/* The I2C bus for DTT		*/
 /*
  * standard dtt sensor configuration - bottom bit will determine local or
  * remote sensor of the ADM1021, the rest determines index into
  * CFG_DTT_ADM1021 array below.
  */
 #define CONFIG_DTT_SENSORS	{ 0, 1 }

 /*
  * ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
  * there will be one entry in this array for each two (dummy) sensors in
  * CONFIG_DTT_SENSORS.
  *
  * For Katmai board:
  * - only one ADM1021
  * - i2c addr 0x18
  * - conversion rate 0x02 = 0.25 conversions/second
  * - ALERT ouput disabled
  * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
  * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
  */
 #define CFG_DTT_ADM1021		{ { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }

 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
 #define	CFG_ENV_IS_IN_FLASH	1	/* Environment uses flash	*/

 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"

 #undef	CONFIG_BOOTARGS

 #define xstr(s) str(s)
 #define str(s) #s

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"hostname=katmai\0"						\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 	"flash_nfs=run nfsargs addip addtty;"				\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 		"bootm\0"						\
 	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
 		"tftp ${fdt_addr} ${fdt_file};"				\
 		"run nfsargs addip addtty;"				\
 		"bootm 200000 - ${fdt_addr}\0"				\
 	"rootpath=/opt/eldk/ppc_4xx\0"					\
 	"bootfile=katmai/uImage\0"					\
 	"fdt_file=katmai/katmai.dtb\0"					\
 	"fdt_addr=400000\0"						\
 	"kernel_addr=fff10000\0"					\
 	"ramdisk_addr=fff20000\0"					\
 	"initrd_high=30000000\0"					\
 	"load=tftp 200000 katmai/u-boot.bin\0"				\
 	"update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"	\
 		"era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"		\
 		"cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
 		"setenv filesize;saveenv\0"				\
 	"upd=run load update\0"						\
 	"kozio=bootm ffc60000\0"					\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:RP:RP\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"

 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP

 #define	CONFIG_IBM_EMAC4_V4	1	/* 440SPe has this EMAC version	*/
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
 #define CONFIG_PHY_RESET_DELAY	1000
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */

 #define CONFIG_NETCONSOLE		/* include NetConsole support	*/
 #define CONFIG_NET_MULTI		/* needed for NetConsole	*/

 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/

 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP				/* undef to save memory		*/
 #define CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/

 #if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS		16		/* max number of command args	*/
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/

 #define CFG_LOAD_ADDR		0x100000	/* default load address		*/
 #define CFG_EXTBDINFO		1		/* To use extended board_into (bd_t) */

 #define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */

 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
 #define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */

 #define CFG_4xx_RESET_TYPE	0x2	/* use chip reset on this board	*/

 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
 #define CFG_FLASH_CFI
 #define CFG_FLASH_CFI_DRIVER
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 #define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/

 #define CFG_FLASH_BANKS_LIST    {CFG_FLASH_BASE}
 #define CFG_MAX_FLASH_BANKS     1		    /* number of banks	    */
 #define CFG_MAX_FLASH_SECT	1024		    /* sectors per device   */

 #undef	CFG_FLASH_CHECKSUM
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

 #define CFG_ENV_SECT_SIZE	0x20000 /* size of one complete sector	*/
 #define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
 #define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

 /* Address and size of Redundant Environment Sector	*/
 #define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)

 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
 /* General PCI */
 #define CONFIG_PCI			/* include pci support		*/
 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
 #define CONFIG_PCI_CONFIG_HOST_BRIDGE

 /* Board-specific PCI */
 #define CFG_PCI_TARGET_INIT		/* let board init pci target    */
 #undef	CFG_PCI_MASTER_INIT

 #define CFG_PCI_SUBSYS_VENDORID 0x1014	/* IBM				*/
 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever			*/
 /* #define CFG_PCI_SUBSYS_ID	CFG_PCI_SUBSYS_DEVICEID */

 /*
  *  NETWORK Support (PCI):
  */
 /* Support for Intel 82557/82559/82559ER chips. */
 #define CONFIG_EEPRO100

 /*-----------------------------------------------------------------------
  * Xilinx System ACE support
  *----------------------------------------------------------------------*/
 #define CONFIG_SYSTEMACE	1	/* Enable SystemACE support	*/
 #define CFG_SYSTEMACE_WIDTH	16	/* Data bus width is 16		*/
 #define CFG_SYSTEMACE_BASE	CFG_ACE_BASE
 #define CONFIG_DOS_PARTITION	1

 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/

 /* Memory Bank 0 (Flash) initialization					*/
 #define CFG_EBC_PB0AP		(EBC_BXAP_BME_DISABLED      |		\
 				 EBC_BXAP_TWT_ENCODE(7)     |		\
 				 EBC_BXAP_BCE_DISABLE       |		\
 				 EBC_BXAP_BCT_2TRANS        |		\
 				 EBC_BXAP_CSN_ENCODE(0)     |		\
 				 EBC_BXAP_OEN_ENCODE(0)     |		\
 				 EBC_BXAP_WBN_ENCODE(0)     |		\
 				 EBC_BXAP_WBF_ENCODE(0)     |		\
 				 EBC_BXAP_TH_ENCODE(0)      |		\
 				 EBC_BXAP_RE_DISABLED       |		\
 				 EBC_BXAP_SOR_DELAYED       |		\
 				 EBC_BXAP_BEM_WRITEONLY     |		\
 				 EBC_BXAP_PEN_DISABLED)
 #define CFG_EBC_PB0CR		(EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) |	\
 				 EBC_BXCR_BS_16MB                    |	\
 				 EBC_BXCR_BU_RW                      |	\
 				 EBC_BXCR_BW_16BIT)

 /* Memory Bank 1 (Xilinx System ACE controller) initialization		*/
 #define CFG_EBC_PB1AP		(EBC_BXAP_BME_DISABLED      |		\
 				 EBC_BXAP_TWT_ENCODE(4)     |		\
 				 EBC_BXAP_BCE_DISABLE       |		\
 				 EBC_BXAP_BCT_2TRANS        |		\
 				 EBC_BXAP_CSN_ENCODE(0)     |		\
 				 EBC_BXAP_OEN_ENCODE(0)     |		\
 				 EBC_BXAP_WBN_ENCODE(0)     |		\
 				 EBC_BXAP_WBF_ENCODE(0)     |		\
 				 EBC_BXAP_TH_ENCODE(0)      |		\
 				 EBC_BXAP_RE_DISABLED       |		\
 				 EBC_BXAP_SOR_NONDELAYED    |		\
 				 EBC_BXAP_BEM_WRITEONLY     |		\
 				 EBC_BXAP_PEN_DISABLED)
 #define CFG_EBC_PB1CR		(EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE)  |	\
 				 EBC_BXCR_BS_1MB                    |	\
 				 EBC_BXCR_BU_RW                     |	\
 				 EBC_BXCR_BW_16BIT)

 /*-------------------------------------------------------------------------
  * Initialize EBC CONFIG -
  * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
  * default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
  *-------------------------------------------------------------------------*/
 #define CFG_EBC_CFG		(EBC_CFG_LE_UNLOCK    |	\
 				 EBC_CFG_PTD_ENABLE   |	\
 				 EBC_CFG_RTC_16PERCLK | \
 				 EBC_CFG_ATC_PREVIOUS | \
 				 EBC_CFG_DTC_PREVIOUS | \
 				 EBC_CFG_CTC_PREVIOUS | \
 				 EBC_CFG_OEO_PREVIOUS | \
 				 EBC_CFG_EMC_DEFAULT  |	\
 				 EBC_CFG_PME_DISABLE  |	\
 				 EBC_CFG_PR_16)

 /*-----------------------------------------------------------------------
  * GPIO Setup
  *----------------------------------------------------------------------*/
 #define CFG_GPIO_PCIE_PRESENT0	17
 #define CFG_GPIO_PCIE_PRESENT1	21
 #define CFG_GPIO_PCIE_PRESENT2	23
 #define CFG_GPIO_RS232_FORCEOFF	30

 #define CFG_PFC0		(GPIO_VAL(CFG_GPIO_PCIE_PRESENT0) | \
 				 GPIO_VAL(CFG_GPIO_PCIE_PRESENT1) | \
 				 GPIO_VAL(CFG_GPIO_PCIE_PRESENT2) | \
 				 GPIO_VAL(CFG_GPIO_RS232_FORCEOFF))
 #define CFG_GPIO_OR		GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
 #define CFG_GPIO_TCR		GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
 #define CFG_GPIO_ODR		0

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/*Initial Memory map for Linux*/

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif

 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2007
	* Stefan Roese, DENX Software Engineering, sr@denx.de.
	*
	* (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/************************************************************************
	* katmai.h - configuration for AMCC Katmai (440SPe)
	***********************************************************************/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*-----------------------------------------------------------------------
	* High Level Configuration Options
	----------------------------------------------------------------------/
	#define CONFIG_KATMAI 1 /* Board is Katmai */
	#define CONFIG_4xx 1 /* ... PPC4xx family */
	#define CONFIG_440 1 /* ... PPC440 family */
	#define CONFIG_440SPE 1 /* Specifc SPe support */
	#undef CFG_DRAM_TEST /* Disable-takes long time */
	#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
	#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
	#undef CONFIG_SHOW_BOOT_PROGRESS

	/*-----------------------------------------------------------------------
	* Base addresses -- Note these are effective addresses where the
	* actual resources get mapped (not physical addresses)
	----------------------------------------------------------------------/
	#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
	#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */
	#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
	#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */

	#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
	#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
	#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE

	#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
	#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */
	#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */

	#define CFG_PCIE0_CFGBASE 0xc0000000
	#define CFG_PCIE1_CFGBASE 0xc1000000
	#define CFG_PCIE2_CFGBASE 0xc2000000
	#define CFG_PCIE0_XCFGBASE 0xc3000000
	#define CFG_PCIE1_XCFGBASE 0xc3001000
	#define CFG_PCIE2_XCFGBASE 0xc3002000

	/* base address of inbound PCIe window */
	#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL

	/* System RAM mapped to PCI space */
	#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
	#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
	#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024)

	#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */

	#define CFG_MONITOR_BASE TEXT_BASE
	#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1)
	#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */

	/*-----------------------------------------------------------------------
	* Initial RAM & stack pointer (placed in internal SRAM)
	----------------------------------------------------------------------/
	#define CFG_TEMP_STACK_OCM 1
	#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
	#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
	#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
	#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */

	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
	#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR

	/*-----------------------------------------------------------------------
	* Serial Port
	----------------------------------------------------------------------/
	#define CONFIG_SERIAL_MULTI 1
	#undef CONFIG_UART1_CONSOLE
	#undef CFG_EXT_SERIAL_CLOCK
	#define CONFIG_BAUDRATE 115200
	#define CFG_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	/*-----------------------------------------------------------------------
	* DDR SDRAM
	----------------------------------------------------------------------/
	#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
	#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/
	#define CONFIG_DDR_ECC 1 /* with ECC support */
	#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/
	#undef CONFIG_STRESS

	/*-----------------------------------------------------------------------
	* I2C
	----------------------------------------------------------------------/
	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#undef CONFIG_SOFT_I2C /* I2C bit-banged */
	#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
	#define CFG_I2C_SLAVE 0x7F

	#define CONFIG_I2C_MULTI_BUS
	#define CONFIG_I2C_CMD_TREE
	#define CFG_SPD_BUS_NUM 0 /* The I2C bus for SPD */

	#define IIC0_BOOTPROM_ADDR 0x50
	#define IIC0_ALT_BOOTPROM_ADDR 0x54

	#define CFG_I2C_MULTI_EEPROMS
	#define CFG_I2C_EEPROM_ADDR (0x50)
	#define CFG_I2C_EEPROM_ADDR_LEN 1
	#define CFG_EEPROM_PAGE_WRITE_ENABLE
	#define CFG_EEPROM_PAGE_WRITE_BITS 3
	#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10

	/* I2C RTC */
	#define CONFIG_RTC_M41T11 1
	#define CFG_RTC_BUS_NUM 1 /* The I2C bus for RTC */
	#define CFG_I2C_RTC_ADDR 0x68
	#define CFG_M41T11_BASE_YEAR 1900 /* play along with linux */

	/* I2C DTT */
	#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
	#define CFG_DTT_BUS_NUM 1 /* The I2C bus for DTT */
	/*
	* standard dtt sensor configuration - bottom bit will determine local or
	* remote sensor of the ADM1021, the rest determines index into
	* CFG_DTT_ADM1021 array below.
	*/
	#define CONFIG_DTT_SENSORS { 0, 1 }

	/*
	* ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
	* there will be one entry in this array for each two (dummy) sensors in
	* CONFIG_DTT_SENSORS.
	*
	* For Katmai board:
	* - only one ADM1021
	* - i2c addr 0x18
	* - conversion rate 0x02 = 0.25 conversions/second
	* - ALERT ouput disabled
	* - local temp sensor enabled, min set to 0 deg, max set to 85 deg
	* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
	*/
	#define CFG_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }

	/*-----------------------------------------------------------------------
	* Environment
	----------------------------------------------------------------------/
	#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */

	#define CONFIG_PREBOOT "echo;" \
	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
	"echo"

	#undef CONFIG_BOOTARGS

	#define xstr(s) str(s)
	#define str(s) #s

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"hostname=katmai\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	"flash_nfs=run nfsargs addip addtty;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip addtty;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
	"bootm\0" \
	"net_nfs_fdt=tftp 200000 ${bootfile};" \
	"tftp ${fdt_addr} ${fdt_file};" \
	"run nfsargs addip addtty;" \
	"bootm 200000 - ${fdt_addr}\0" \
	"rootpath=/opt/eldk/ppc_4xx\0" \
	"bootfile=katmai/uImage\0" \
	"fdt_file=katmai/katmai.dtb\0" \
	"fdt_addr=400000\0" \
	"kernel_addr=fff10000\0" \
	"ramdisk_addr=fff20000\0" \
	"initrd_high=30000000\0" \
	"load=tftp 200000 katmai/u-boot.bin\0" \
	"update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
	"era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \
	"cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
	"setenv filesize;saveenv\0" \
	"upd=run load update\0" \
	"kozio=bootm ffc60000\0" \
	"pciconfighost=1\0" \
	"pcie_mode=RP:RP:RP\0" \
	""
	#define CONFIG_BOOTCOMMAND "run flash_self"

	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_DIAG
	#define CONFIG_CMD_DTT
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_NET
	#define CONFIG_CMD_NFS
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_REGINFO
	#define CONFIG_CMD_SDRAM
	#define CONFIG_CMD_SNTP

	#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */
	#define CONFIG_MII 1 /* MII PHY management */
	#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
	#define CONFIG_HAS_ETH0
	#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
	#define CONFIG_PHY_RESET_DELAY 1000
	#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
	#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
	#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */

	#define CONFIG_NETCONSOLE /* include NetConsole support */
	#define CONFIG_NET_MULTI /* needed for NetConsole */

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CFG_LONGHELP /* undef to save memory */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */

	#if defined(CONFIG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */

	#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
	#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */

	#define CFG_LOAD_ADDR 0x100000 /* default load address */
	#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */

	#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	#define CONFIG_LOOPW 1 /* enable loopw command */
	#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
	#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */

	#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */

	/*-----------------------------------------------------------------------
	* FLASH related
	----------------------------------------------------------------------/
	#define CFG_FLASH_CFI
	#define CFG_FLASH_CFI_DRIVER
	#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
	#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */

	#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
	#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
	#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */

	#undef CFG_FLASH_CHECKSUM
	#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
	#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */

	/* Address and size of Redundant Environment Sector */
	#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
	#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)

	/*-----------------------------------------------------------------------
	* PCI stuff
	*-----------------------------------------------------------------------
	*/
	/* General PCI */
	#define CONFIG_PCI /* include pci support */
	#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
	#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
	#define CONFIG_PCI_CONFIG_HOST_BRIDGE

	/* Board-specific PCI */
	#define CFG_PCI_TARGET_INIT /* let board init pci target */
	#undef CFG_PCI_MASTER_INIT

	#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
	#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
	/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */

	/*
	* NETWORK Support (PCI):
	*/
	/* Support for Intel 82557/82559/82559ER chips. */
	#define CONFIG_EEPRO100

	/*-----------------------------------------------------------------------
	* Xilinx System ACE support
	----------------------------------------------------------------------/
	#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */
	#define CFG_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */
	#define CFG_SYSTEMACE_BASE CFG_ACE_BASE
	#define CONFIG_DOS_PARTITION 1

	/*-----------------------------------------------------------------------
	* External Bus Controller (EBC) Setup
	----------------------------------------------------------------------/

	/* Memory Bank 0 (Flash) initialization */
	#define CFG_EBC_PB0AP (EBC_BXAP_BME_DISABLED \| \
	EBC_BXAP_TWT_ENCODE(7) \| \
	EBC_BXAP_BCE_DISABLE \| \
	EBC_BXAP_BCT_2TRANS \| \
	EBC_BXAP_CSN_ENCODE(0) \| \
	EBC_BXAP_OEN_ENCODE(0) \| \
	EBC_BXAP_WBN_ENCODE(0) \| \
	EBC_BXAP_WBF_ENCODE(0) \| \
	EBC_BXAP_TH_ENCODE(0) \| \
	EBC_BXAP_RE_DISABLED \| \
	EBC_BXAP_SOR_DELAYED \| \
	EBC_BXAP_BEM_WRITEONLY \| \
	EBC_BXAP_PEN_DISABLED)
	#define CFG_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) \| \
	EBC_BXCR_BS_16MB \| \
	EBC_BXCR_BU_RW \| \
	EBC_BXCR_BW_16BIT)

	/* Memory Bank 1 (Xilinx System ACE controller) initialization */
	#define CFG_EBC_PB1AP (EBC_BXAP_BME_DISABLED \| \
	EBC_BXAP_TWT_ENCODE(4) \| \
	EBC_BXAP_BCE_DISABLE \| \
	EBC_BXAP_BCT_2TRANS \| \
	EBC_BXAP_CSN_ENCODE(0) \| \
	EBC_BXAP_OEN_ENCODE(0) \| \
	EBC_BXAP_WBN_ENCODE(0) \| \
	EBC_BXAP_WBF_ENCODE(0) \| \
	EBC_BXAP_TH_ENCODE(0) \| \
	EBC_BXAP_RE_DISABLED \| \
	EBC_BXAP_SOR_NONDELAYED \| \
	EBC_BXAP_BEM_WRITEONLY \| \
	EBC_BXAP_PEN_DISABLED)
	#define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) \| \
	EBC_BXCR_BS_1MB \| \
	EBC_BXCR_BU_RW \| \
	EBC_BXCR_BW_16BIT)

	/*-------------------------------------------------------------------------
	* Initialize EBC CONFIG -
	* Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
	* default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
	-------------------------------------------------------------------------/
	#define CFG_EBC_CFG (EBC_CFG_LE_UNLOCK \| \
	EBC_CFG_PTD_ENABLE \| \
	EBC_CFG_RTC_16PERCLK \| \
	EBC_CFG_ATC_PREVIOUS \| \
	EBC_CFG_DTC_PREVIOUS \| \
	EBC_CFG_CTC_PREVIOUS \| \
	EBC_CFG_OEO_PREVIOUS \| \
	EBC_CFG_EMC_DEFAULT \| \
	EBC_CFG_PME_DISABLE \| \
	EBC_CFG_PR_16)

	/*-----------------------------------------------------------------------
	* GPIO Setup
	----------------------------------------------------------------------/
	#define CFG_GPIO_PCIE_PRESENT0 17
	#define CFG_GPIO_PCIE_PRESENT1 21
	#define CFG_GPIO_PCIE_PRESENT2 23
	#define CFG_GPIO_RS232_FORCEOFF 30

	#define CFG_PFC0 (GPIO_VAL(CFG_GPIO_PCIE_PRESENT0) \| \
	GPIO_VAL(CFG_GPIO_PCIE_PRESENT1) \| \
	GPIO_VAL(CFG_GPIO_PCIE_PRESENT2) \| \
	GPIO_VAL(CFG_GPIO_RS232_FORCEOFF))
	#define CFG_GPIO_OR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
	#define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
	#define CFG_GPIO_ODR 0

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /Initial Memory map for Linux/

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif

	/* pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1

	#endif /* __CONFIG_H */