| /* |
| * (C) Copyright 2007 Netstal Maschinen AG |
| * Niklaus Giger (Niklaus.Giger@netstal.com) |
| * |
| * (C) Copyright 2006-2007 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * (C) Copyright 2006 |
| * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com |
| * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /************************************************************************ |
| * hcu5.h - configuration for HCU5 board (derived from sequoia.h) |
| ***********************************************************************/ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*----------------------------------------------------------------------- |
| * High Level Configuration Options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_HCU5 1 /* Board is HCU5 */ |
| #define CONFIG_440EPX 1 /* Specific PPC440EPx */ |
| #define CONFIG_440 1 /* ... PPC440 family */ |
| #define CONFIG_4xx 1 /* ... PPC4xx family */ |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ |
| |
| /*----------------------------------------------------------------------- |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| *----------------------------------------------------------------------*/ |
| #define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */ |
| #define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ |
| |
| #define CFG_TLB_FOR_BOOT_FLASH 3 |
| #define CFG_BOOT_BASE_ADDR 0xfff00000 |
| #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ |
| #define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */ |
| #define CFG_MONITOR_BASE TEXT_BASE |
| #define CFG_OCM_BASE 0xe0010000 /* ocm */ |
| #define CFG_OCM_DATA_ADDR CFG_OCM_BASE |
| #define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ |
| #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ |
| #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 |
| #define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 |
| #define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 |
| |
| /* Don't change either of these */ |
| #define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ |
| |
| #define CFG_USB2D0_BASE 0xe0000100 |
| #define CFG_USB_DEVICE 0xe0000000 |
| #define CFG_USB_HOST 0xe0000400 |
| |
| /*----------------------------------------------------------------------- |
| * Initial RAM & stack pointer |
| *----------------------------------------------------------------------*/ |
| /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ |
| #define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ |
| |
| #define CFG_INIT_RAM_END (4 << 10) |
| #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR |
| |
| /*----------------------------------------------------------------------- |
| * Serial Port |
| *----------------------------------------------------------------------*/ |
| #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ |
| #define CONFIG_BAUDRATE 9600 |
| #define CONFIG_SERIAL_MULTI 1 |
| /* needed to be able to define |
| CONFIG_SERIAL_SOFTWARE_FIFO, but |
| CONFIG_SERIAL_SOFTWARE_FIFO (16) does not work */ |
| /* Size (bytes) of interrupt driven serial port buffer. |
| * Set to 0 to use polling instead of interrupts. |
| * Setting to 0 will also disable RTS/CTS handshaking. |
| */ |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #undef CONFIG_UART1_CONSOLE |
| |
| #undef CONFIG_CMD_HWFLOW |
| #define CFG_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| /*----------------------------------------------------------------------- |
| * Environment |
| *----------------------------------------------------------------------*/ |
| |
| #undef CFG_ENV_IS_IN_NVRAM |
| #define CFG_ENV_IS_IN_FLASH |
| #undef CFG_ENV_IS_IN_EEPROM |
| #undef CFG_ENV_IS_NOWHERE |
| |
| #ifdef CFG_ENV_IS_IN_EEPROM |
| /* Put the environment after the SDRAM and bootstrap configuration */ |
| #define PROM_SIZE 2048 |
| #define CFG_BOOSTRAP_OPTION_OFFSET 512 |
| #define CFG_ENV_OFFSET (CFG_BOOSTRAP_OPTION_OFFSET + 0x10) |
| #define CFG_ENV_SIZE (PROM_SIZE-CFG_ENV_OFFSET) |
| #endif |
| |
| #ifdef CFG_ENV_IS_IN_FLASH |
| /* Put the environment in Flash */ |
| #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ |
| #define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) |
| |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * DDR SDRAM |
| *----------------------------------------------------------------------*/ |
| #define CFG_MBYTES_SDRAM (128) /* 128 MB or 256 MB */ |
| #define CFG_DDR_CACHED_ADDR 0x50000000 /* setup 2nd TLB cached here */ |
| #undef CONFIG_DDR_DATA_EYE /* Do not use DDR2 optimization */ |
| #define CONFIG_DDR_ECC 1 /* enable ECC */ |
| |
| /* Following two definitions must be kept in sync with config.h of vxWorks */ |
| #define USER_RESERVED_MEM ( 0) /* in kB */ |
| #define PM_RESERVED_MEM ( 64) /* in kB: pmLib reserved area size */ |
| #define CONFIG_PRAM ( USER_RESERVED_MEM + PM_RESERVED_MEM ) |
| |
| /*----------------------------------------------------------------------- |
| * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the |
| * the second internal I2C controller of the PPC440EPx |
| *----------------------------------------------------------------------*/ |
| #define CFG_SPD_BUS_NUM 1 |
| |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CFG_I2C_SLAVE 0x7F |
| |
| /* This is the 7bit address of the device, not including P. */ |
| #define CFG_I2C_EEPROM_ADDR 0x50 |
| #define CFG_I2C_EEPROM_ADDR_LEN 1 |
| |
| /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ |
| #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 |
| #define CFG_EEPROM_PAGE_WRITE_BITS 4 |
| #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 |
| #define CFG_EEPROM_PAGE_WRITE_ENABLE |
| #undef CFG_I2C_MULTI_EEPROMS |
| |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \"run nfs\" to mount Linux root filesystem over NFS;"\ |
| "echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| /* Setup some board specific values for the default environment variables */ |
| #define CONFIG_HOSTNAME hcu5 |
| #define CONFIG_IPADDR 172.25.1.99 |
| #define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ |
| #define CONFIG_OVERWRITE_ETHADDR_ONCE |
| #define CONFIG_SERVERIP 172.25.1.3 |
| |
| #define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "loadaddr=0x01000000\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ |
| "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ |
| "bootm\0" \ |
| "bootfile=hcu5/uImage\0" \ |
| "rootpath=/home/hcu/eldk/ppc_4xxFP\0" \ |
| "load=tftp 100000 hcu5/u-boot.bin\0" \ |
| "update=protect off FFFB0000 FFFFFFFF;era FFFB0000 FFFFFFFF;" \ |
| "cp.b 100000 FFFB0000 50000\0" \ |
| "upd=run load update\0" \ |
| "vx_rom=hcu5/hcu5_vx_rom\0" \ |
| "vx=tftp ${loadaddr} ${vx_rom};run vxargs; bootvx\0" \ |
| "vxargs=setenv bootargs emac(0,0)c:${vx_rom} e=${ipaddr}" \ |
| " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008\0" \ |
| "usbargs=setenv bootargs root=/dev/sda1 ro\0" \ |
| "linux=usb start; ext2load usb 0 ${loadaddr} /boot/uImage;" \ |
| "run usbargs addip addtty; bootm\0" \ |
| "net_nfs_fdt=tftp 200000 ${bootfile};" \ |
| "tftp ${fdt_addr} ${fdt_file};" \ |
| "run nfsargs addip addtty;" \ |
| "bootm 200000 - ${fdt_addr}\0" \ |
| "fdt_file=hcu5/hcu5.dtb\0" \ |
| "fdt_addr=400000\0" \ |
| "" |
| #define CONFIG_BOOTCOMMAND "run vx" |
| |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| #define CONFIG_M88E1111_PHY 1 |
| #define CONFIG_IBM_EMAC4_V4 1 |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 1 /* PHY address, like on HCU4 */ |
| |
| #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ |
| |
| #define CONFIG_HAS_ETH0 |
| #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & desc. */ |
| |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ |
| #define CONFIG_PHY1_ADDR 2 |
| |
| /* USB */ |
| #define CONFIG_USB_OHCI |
| #define CONFIG_USB_STORAGE |
| |
| /* Comment this out to enable USB 1.1 device */ |
| #define USB_2_0_DEVICE |
| |
| /* Partitions */ |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_DIAG |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IMMAP |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_SDRAM |
| #define CONFIG_CMD_USB |
| |
| /* POST support */ |
| #define CONFIG_POST (CFG_POST_MEMORY | \ |
| CFG_POST_CPU | \ |
| CFG_POST_UART | \ |
| CFG_POST_I2C | \ |
| CFG_POST_CACHE | \ |
| CFG_POST_FPU | \ |
| CFG_POST_ETHER | \ |
| CFG_POST_SPR) |
| #define CFG_POST_UART_TABLE {UART0_BASE} |
| |
| #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) |
| #define CFG_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ |
| #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ |
| |
| #define CONFIG_SUPPORT_VFAT |
| |
| /*----------------------------------------------------------------------- |
| * Miscellaneous configurable options |
| *----------------------------------------------------------------------*/ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x100000 /* default load address */ |
| #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_LOOPW 1 /* enable loopw command */ |
| #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------*/ |
| /* General PCI */ |
| #define CONFIG_PCI 1 /* include pci support */ |
| #undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr map to CFG_PCI_MEMBASE*/ |
| |
| /* Board-specific PCI */ |
| #define CFG_PCI_TARGET_INIT |
| #define CFG_PCI_MASTER_INIT |
| |
| #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ |
| #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * Flash |
| *----------------------------------------------------------------------*/ |
| |
| /* Use common CFI driver */ |
| #define CFG_FLASH_CFI |
| #define CFG_FLASH_CFI_DRIVER |
| /* board provides its own flash_init code */ |
| #define CONFIG_FLASH_CFI_LEGACY 1 |
| #define CFG_FLASH_CFI_WIDTH FLASH_CFI_8BIT |
| #define CFG_FLASH_LEGACY_512Kx8 1 |
| |
| /* print 'E' for empty sector on flinfo */ |
| #define CFG_FLASH_EMPTY_INFO |
| |
| #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| *----------------------------------------------------------------------*/ |
| #define CFG_FLASH CFG_FLASH_BASE |
| #define CFG_CS_1 0xC8000000 /* CAN */ |
| #define CFG_CS_2 0xCC000000 /* CPLD and IMC-Bus Standard */ |
| #define CFG_CPLD CFG_CS_2 |
| #define CFG_CS_3 0xCE000000 /* CPLD and IMC-Bus Fast */ |
| |
| #define CFG_BOOTFLASH_CS 0 /* Boot Flash chip connected to CSx */ |
| #define CFG_EBC_PB0AP 0x02005400 |
| #define CFG_EBC_PB0CR 0xFFF18000 /* (CFG_FLASH | 0xda000) */ |
| #define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ |
| |
| /* Memory Bank 1 CAN-Chips initialization */ |
| #define CFG_EBC_PB1AP 0x02054500 |
| #define CFG_EBC_PB1CR 0xC8018000 |
| |
| /* Memory Bank 2 CPLD/IMC-Bus standard initialization */ |
| #define CFG_EBC_PB2AP 0x01840300 |
| #define CFG_EBC_PB2CR 0xCC0BA000 |
| |
| /* Memory Bank 3 IMC-Bus fast mode initialization */ |
| #define CFG_EBC_PB3AP 0x01800300 |
| #define CFG_EBC_PB3CR 0xCE0BA000 |
| |
| /* Memory Bank 4 (not used) initialization */ |
| #undef CFG_EBC_PB4AP |
| #undef CFG_EBC_PB4CR |
| |
| /* Memory Bank 5 (not used) initialization */ |
| #undef CFG_EBC_PB5AP |
| #undef CFG_EBC_PB5CR |
| |
| #define HCU_CPLD_VERSION_REGISTER ( CFG_CPLD + 0x0F00000 ) |
| #define HCU_HW_VERSION_REGISTER ( CFG_CPLD + 0x1400000 ) |
| |
| #define CFG_HUSH_PARSER /* use "hush" command parser */ |
| #ifdef CFG_HUSH_PARSER |
| #define CFG_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| |
| #endif /* __CONFIG_H */ |