| /* |
| * (C) Copyright 2003-2006 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * (C) Copyright 2004-2005 |
| * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ |
| #define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ |
| #define CONFIG_TQM5200 1 /* ... on TQM5200 module */ |
| #undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ |
| #define CONFIG_STK52XX 1 /* ... on a STK52XX base board */ |
| #define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */ |
| #define CONFIG_AEVFIFO 1 |
| #define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ |
| |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| /* |
| * Serial console configuration |
| */ |
| #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ |
| #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ |
| #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| |
| /* |
| * PCI Mapping: |
| * 0x40000000 - 0x4fffffff - PCI Memory |
| * 0x50000000 - 0x50ffffff - PCI IO Space |
| */ |
| #ifdef CONFIG_AEVFIFO |
| #define CONFIG_PCI 1 |
| #define CONFIG_PCI_PNP 1 |
| /* #define CONFIG_PCI_SCAN_SHOW 1 */ |
| #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 |
| |
| #define CONFIG_PCI_MEM_BUS 0x40000000 |
| #define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS |
| #define CONFIG_PCI_MEM_SIZE 0x10000000 |
| |
| #define CONFIG_PCI_IO_BUS 0x50000000 |
| #define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS |
| #define CONFIG_PCI_IO_SIZE 0x01000000 |
| |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_EEPRO100 1 |
| #define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ |
| #define CONFIG_NS8382X 1 |
| #endif /* CONFIG_AEVFIFO */ |
| |
| /* Partitions */ |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| |
| /* POST support */ |
| #define CONFIG_POST (CFG_POST_MEMORY | \ |
| CFG_POST_CPU | \ |
| CFG_POST_I2C) |
| |
| #ifdef CONFIG_POST |
| /* preserve space for the post_word at end of on-chip SRAM */ |
| #define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 |
| #endif |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_ECHO |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_SNTP |
| |
| #ifdef CONFIG_POST |
| #define CONFIG_CMD_DIAG |
| #endif |
| |
| |
| #define CONFIG_TIMESTAMP /* display image timestamps */ |
| |
| #if (TEXT_BASE == 0xFC000000) /* Boot low */ |
| # define CFG_LOWBOOT 1 |
| #endif |
| |
| /* |
| * Autobooting |
| */ |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ |
| "echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "rootpath=/opt/eldk/ppc_6xx\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath} " \ |
| "console=ttyS0,${baudrate}\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "flash_self=run ramargs addip;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "flash_nfs=run nfsargs addip;" \ |
| "bootm ${kernel_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ |
| "bootfile=/tftpboot/tqm5200/uImage\0" \ |
| "load=tftp 200000 ${u-boot}\0" \ |
| "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ |
| "update=protect off FC000000 FC05FFFF;" \ |
| "erase FC000000 FC05FFFF;" \ |
| "cp.b 200000 FC000000 ${filesize};" \ |
| "protect on FC000000 FC05FFFF\0" \ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run net_nfs" |
| |
| /* |
| * IPB Bus clocking configuration. |
| */ |
| #define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ |
| |
| #if defined(CFG_IPBCLK_EQUALS_XLBCLK) |
| /* |
| * PCI Bus clocking configuration |
| * |
| * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if |
| * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock |
| * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. |
| */ |
| #define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ |
| #endif |
| |
| /* |
| * I2C configuration |
| */ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #ifdef CONFIG_TQM5200_REV100 |
| #define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ |
| #else |
| #define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ |
| #endif |
| |
| /* |
| * I2C clock frequency |
| * |
| * Please notice, that the resulting clock frequency could differ from the |
| * configured value. This is because the I2C clock is derived from system |
| * clock over a frequency divider with only a few divider values. U-boot |
| * calculates the best approximation for CFG_I2C_SPEED. However the calculated |
| * approximation allways lies below the configured value, never above. |
| */ |
| #define CFG_I2C_SPEED 100000 /* 100 kHz */ |
| #define CFG_I2C_SLAVE 0x7F |
| |
| /* |
| * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work |
| * also). For other EEPROMs configuration should be verified. On Mini-FAP the |
| * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the |
| * same configuration could be used. |
| */ |
| #define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ |
| #define CFG_I2C_EEPROM_ADDR_LEN 2 |
| #define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ |
| #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 |
| |
| /* |
| * Flash configuration |
| */ |
| #define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */ |
| |
| /* use CFI flash driver if no module variant is spezified */ |
| #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ |
| #define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } |
| #define CFG_FLASH_EMPTY_INFO |
| #define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ |
| #define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ |
| #undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ |
| |
| #if !defined(CFG_LOWBOOT) |
| #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000) |
| #else /* CFG_LOWBOOT */ |
| #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) |
| #endif /* CFG_LOWBOOT */ |
| #define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks |
| (= chip selects) */ |
| #define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ |
| |
| |
| /* |
| * Environment settings |
| */ |
| #define CFG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_SIZE 0x10000 |
| #define CFG_ENV_SECT_SIZE 0x20000 |
| #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) |
| |
| /* |
| * Memory map |
| */ |
| #define CFG_MBAR 0xF0000000 |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_DEFAULT_MBAR 0x80000000 |
| |
| /* Use ON-Chip SRAM until RAM will be available */ |
| #define CFG_INIT_RAM_ADDR MPC5XXX_SRAM |
| #ifdef CONFIG_POST |
| /* preserve space for the post_word at end of on-chip SRAM */ |
| #define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE |
| #else |
| #define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE |
| #endif |
| |
| |
| #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET |
| |
| #define CFG_MONITOR_BASE TEXT_BASE |
| #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) |
| # define CFG_RAMBOOT 1 |
| #endif |
| |
| #define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ |
| #define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Ethernet configuration |
| */ |
| #define CONFIG_MPC5xxx_FEC 1 |
| /* |
| * Define CONFIG_FEC_10MBIT to force FEC at 10Mb |
| */ |
| /* #define CONFIG_FEC_10MBIT 1 */ |
| #define CONFIG_PHY_ADDR 0x00 |
| |
| /* |
| * GPIO configuration |
| * |
| * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): |
| * Bit 0 (mask: 0x80000000): 1 |
| * use ALT CAN position: Bits 2-3 (mask: 0x30000000): |
| * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. |
| * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. |
| * Use for REV200 STK52XX boards. Do not use with REV100 modules |
| * (because, there I2C1 is used as I2C bus) |
| * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 |
| * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) |
| * 000 -> All PSC2 pins are GIOPs |
| * 001 -> CAN1/2 on PSC2 pins |
| * Use for REV100 STK52xx boards |
| * use PSC6: |
| * on STK52xx: |
| * use as UART. Pins PSC6_0 to PSC6_3 are used. |
| * Bits 9:11 (mask: 0x00700000): |
| * 101 -> PSC6 : Extended POST test is not available |
| * on MINI-FAP and TQM5200_IB: |
| * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): |
| * 000 -> PSC6 could not be used as UART, CODEC or IrDA |
| * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST |
| * tests. |
| */ |
| #define CFG_GPS_PORT_CONFIG 0x81500014 |
| |
| /* |
| * RTC configuration |
| */ |
| #define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| /* Enable an alternate, more extensive memory test */ |
| #define CFG_ALT_MEMTEST |
| |
| #define CFG_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x100000 /* default load address */ |
| |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| # define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /* |
| * Enable loopw command. |
| */ |
| #define CONFIG_LOOPW |
| |
| /* |
| * Various low-level settings |
| */ |
| #if defined(CONFIG_MPC5200) |
| #define CFG_HID0_INIT HID0_ICE | HID0_ICFI |
| #define CFG_HID0_FINAL HID0_ICE |
| #else |
| #define CFG_HID0_INIT 0 |
| #define CFG_HID0_FINAL 0 |
| #endif |
| |
| #define CFG_BOOTCS_START CFG_FLASH_BASE |
| #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE |
| #ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 |
| #define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ |
| #else |
| #define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ |
| #endif |
| #define CFG_CS0_START CFG_FLASH_BASE |
| #define CFG_CS0_SIZE CFG_FLASH_SIZE |
| |
| #define CONFIG_LAST_STAGE_INIT |
| |
| /* |
| * SRAM - Do not map below 2 GB in address space, because this area is used |
| * for SDRAM autosizing. |
| */ |
| #define CFG_CS2_START 0xE5000000 |
| #define CFG_CS2_SIZE 0x80000 /* 512 kByte */ |
| #define CFG_CS2_CFG 0x0004D930 |
| |
| /* |
| * Grafic controller - Do not map below 2 GB in address space, because this |
| * area is used for SDRAM autosizing. |
| */ |
| #define SM501_FB_BASE 0xE0000000 |
| #define CFG_CS1_START (SM501_FB_BASE) |
| #define CFG_CS1_SIZE 0x4000000 /* 64 MByte */ |
| #define CFG_CS1_CFG 0x8F48FF70 |
| #define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000 |
| |
| #define CFG_CS_BURST 0x00000000 |
| #define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ |
| |
| #define CFG_RESET_ADDRESS 0xff000000 |
| |
| #endif /* __CONFIG_H */ |