| # |
| # (C) Copyright 2010 |
| # Heiko Schocher, DENX Software Engineering, hs@denx.de. |
| # |
| # (C) Copyright 2011 |
| # Valentin Longchamp, Keymile AG, valentin.longchamp@keymile.com |
| # |
| # SPDX-License-Identifier: GPL-2.0+ |
| # |
| # Refer doc/README.kwbimage for more details about how-to configure |
| # and create kirkwood boot image |
| # |
| |
| # Boot Media configurations |
| BOOT_FROM spi # Boot from SPI flash |
| |
| DATA 0xFFD10000 0x01112222 # MPP Control 0 Register |
| # bit 3-0: MPPSel0 2, NF_IO[2] |
| # bit 7-4: MPPSel1 2, NF_IO[3] |
| # bit 12-8: MPPSel2 2, NF_IO[4] |
| # bit 15-12: MPPSel3 2, NF_IO[5] |
| # bit 19-16: MPPSel4 1, NF_IO[6] |
| # bit 23-20: MPPSel5 1, NF_IO[7] |
| # bit 27-24: MPPSel6 1, SYSRST_O |
| # bit 31-28: MPPSel7 0, GPO[7] |
| |
| DATA 0xFFD10004 0x03303300 |
| |
| DATA 0xFFD10008 0x00001100 # MPP Control 2 Register |
| # bit 3-0: MPPSel16 0, GPIO[16] |
| # bit 7-4: MPPSel17 0, GPIO[17] |
| # bit 12-8: MPPSel18 1, NF_IO[0] |
| # bit 15-12: MPPSel19 1, NF_IO[1] |
| # bit 19-16: MPPSel20 0, GPIO[20] |
| # bit 23-20: MPPSel21 0, GPIO[21] |
| # bit 27-24: MPPSel22 0, GPIO[22] |
| # bit 31-28: MPPSel23 0, GPIO[23] |
| |
| DATA 0xFFD100E0 0x1B1B1B1B # IO Configuration 0 Register |
| DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register |
| DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register |
| |
| # NOTE: Don't write on 0x20148 , 0x2014c and 0x20154, leave them untouched! |
| # If not it could cause KW Exceptions during boot in Fast Corners/High Voltage |
| |
| #Dram initalization |
| DATA 0xFFD01400 0x430004E0 # SDRAM Configuration Register |
| # bit13-0: 0x4E0 (DDR2 clks refresh rate) |
| # bit23-14: zero |
| # bit24: 1= enable exit self refresh mode on DDR access |
| # bit25: 1 required |
| # bit29-26: zero |
| # bit31-30: 01 |
| |
| DATA 0xFFD01404 0x38543000 # DDR Controller Control Low |
| # bit 3-0: 0 reserved |
| # bit 4: 0=addr/cmd in smame cycle |
| # bit 5: 0=clk is driven during self refresh, we don't care for APX |
| # bit 6: 0=use recommended falling edge of clk for addr/cmd |
| # bit14: 0=input buffer always powered up |
| # bit18: 1=cpu lock transaction enabled |
| # bit23-20: 5=recommended value for CL=4 and STARTBURST_DEL disabled bit31=0 |
| # bit27-24: 8= CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM |
| # bit30-28: 3 required |
| # bit31: 0=no additional STARTBURST delay |
| |
| DATA 0xFFD01408 0x2302433E # DDR Timing (Low) (active cycles value +1) |
| # bit3-0: TRAS lsbs |
| # bit7-4: TRCD |
| # bit11- 8: TRP |
| # bit15-12: TWR |
| # bit19-16: TWTR |
| # bit20: TRAS msb |
| # bit23-21: 0x0 |
| # bit27-24: TRRD |
| # bit31-28: TRTP |
| |
| DATA 0xFFD0140C 0x00000A3E # DDR Timing (High) |
| # bit6-0: TRFC |
| # bit8-7: TR2R |
| # bit10-9: TR2W |
| # bit12-11: TW2W |
| # bit31-13: zero required |
| |
| DATA 0xFFD01410 0x00000001 # DDR Address Control |
| # bit1-0: 01, Cs0width=x16 |
| # bit3-2: 00, Cs0size=2Gb |
| # bit5-4: 00, Cs2width=nonexistent |
| # bit7-6: 00, Cs1size =nonexistent |
| # bit9-8: 00, Cs2width=nonexistent |
| # bit11-10: 00, Cs2size =nonexistent |
| # bit13-12: 00, Cs3width=nonexistent |
| # bit15-14: 00, Cs3size =nonexistent |
| # bit16: 0, Cs0AddrSel |
| # bit17: 0, Cs1AddrSel |
| # bit18: 0, Cs2AddrSel |
| # bit19: 0, Cs3AddrSel |
| # bit31-20: 0 required |
| |
| DATA 0xFFD01414 0x00000000 # DDR Open Pages Control |
| # bit0: 0, OpenPage enabled |
| # bit31-1: 0 required |
| |
| DATA 0xFFD01418 0x00000000 # DDR Operation |
| # bit3-0: 0x0, DDR cmd |
| # bit31-4: 0 required |
| |
| DATA 0xFFD0141C 0x00000652 # DDR Mode |
| DATA 0xFFD01420 0x00000006 # DDR Extended Mode |
| # bit0: 0, DDR DLL enabled |
| # bit1: 1, DDR drive strenght reduced |
| # bit2: 1, DDR ODT control lsd disabled |
| # bit5-3: 000, required |
| # bit6: 0, DDR ODT control msb disabled |
| # bit9-7: 000, required |
| # bit10: 0, differential DQS enabled |
| # bit11: 0, required |
| # bit12: 0, DDR output buffer enabled |
| # bit31-13: 0 required |
| |
| DATA 0xFFD01424 0x0000F17F # DDR Controller Control High |
| # bit2-0: 111, required |
| # bit3 : 1 , MBUS Burst Chop disabled |
| # bit6-4: 111, required |
| # bit7 : 0 |
| # bit8 : 1 , add a sample stage |
| # bit9 : 0 , no half clock cycle addition to dataout |
| # bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals |
| # bit11 : 0 , 1/4 clock cycle skew disabled for write mesh |
| # bit15-12: 1111 required |
| # bit31-16: 0 required |
| |
| DATA 0xFFD01428 0x00084520 # DDR2 SDRAM Timing Low |
| # bit3-0 : 0000, required |
| # bit7-4 : 0010, M_ODT assertion 2 cycles after read |
| # bit11-8 : 0101, M_ODT de-assertion 5 cycles after read |
| # bit15-12: 0100, internal ODT assertion 4 cycles after read |
| # bit19-16: 1000, internal ODT de-assertion 8 cycles after read |
| # bit31-20: 0 , required |
| |
| DATA 0xFFD0147c 0x00008451 # DDR2 SDRAM Timing High |
| # bit3-0 : 0001, M_ODT assertion same cycle as write |
| # bit7-4 : 0101, M_ODT de-assertion x cycles after write |
| # bit11-8 : 0100, internal ODT assertion x cycles after write |
| # bit15-12: 1000, internal ODT de-assertion x cycles after write |
| |
| DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 |
| DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size |
| # bit0: 1, Window enabled |
| # bit1: 0, Write Protect disabled |
| # bit3-2: 00, CS0 hit selected |
| # bit23-4: ones, required |
| # bit31-24: 0x0F, Size (i.e. 256MB) |
| |
| DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled |
| DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled |
| DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled |
| |
| DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) |
| # bit3-0: 0, ODT0Rd, MODT[0] not asserted during read from DRAM CS0 |
| # bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 |
| |
| DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) |
| # bit1-0: 00, ODT0 controlled by ODT Control (low) register above |
| # bit3-2: 00, ODT1 controlled by register |
| # bit31-4: zero, required |
| |
| DATA 0xFFD0149C 0x0000F801 # CPU ODT Control |
| # bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 |
| # bit7-4: 0, ODT0Wr, Internal ODT not asserted during write to DRAM bank0 |
| # bit9-8: 0, ODTEn, controlled by ODT0Rd and ODT0Wr |
| # bit11-10:2, DQ_ODTSel. ODT select turned on, 75 ohm |
| # bit13-12:3, STARTBURST ODT buffer selected, 50 ohm |
| # bit14 :1, STARTBURST ODT enabled |
| # bit15 :1, Use ODT Block |
| |
| DATA 0xFFD01480 0x00000001 # DDR Initialization Control |
| # bit0=1, enable DDR init upon this register write |
| |
| # End of Header extension |
| DATA 0x0 0x0 |