include/configs/bf533-ezkit.h - github/trini/u-boot - Gitiles

 /*
  * U-boot - Configuration file for BF533 EZKIT board
  */

 #ifndef __CONFIG_EZKIT533_H__
 #define __CONFIG_EZKIT533_H__

 #define CONFIG_BAUDRATE		57600
 #define CONFIG_STAMP		1

 #define CONFIG_BOOTDELAY	5
 #define CFG_AUTOLOAD		"no"	/*rarpb, bootp or dhcp commands will perform only a */

 #define CFG_LONGHELP		1
 #define CONFIG_CMDLINE_EDITING	1
 #define CONFIG_LOADADDR		0x01000000	/* default load address */
 #define CONFIG_BOOTCOMMAND	"tftp $(loadaddr) linux"
 /* #define CONFIG_BOOTARGS		"root=/dev/mtdblock0 rw" */

 #define CONFIG_DRIVER_SMC91111	1
 #define CONFIG_SMC91111_BASE	0x20310300

 #if 0
 #define	CONFIG_MII
 #define CFG_DISCOVER_PHY
 #endif

 #define CONFIG_RTC_BFIN		1
 #define CONFIG_BOOT_RETRY_TIME	-1	/* Enable this if bootretry required, currently its disabled */

 /*
  * Boot Mode Set
  * Blackfin can support several boot modes
  */
 #define BF533_BYPASS_BOOT	0x0001	/* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
 #define BF533_PARA_BOOT		0x0002	/* Bootmode 1: Boot from 8-bit or 16-bit flash */
 #define BF533_SPI_BOOT		0x0004	/* Bootmode 3: Boot from SPI flash */
 /* Define the boot mode */
 #define BFIN_BOOT_MODE		BF533_BYPASS_BOOT
 /* #define BFIN_BOOT_MODE	BF533_SPI_BOOT */

 #define CONFIG_PANIC_HANG 1

 #define ADSP_BF531		0x31
 #define ADSP_BF532		0x32
 #define ADSP_BF533		0x33
 #define BFIN_CPU		ADSP_BF533

 /* This sets the default state of the cache on U-Boot's boot */
 #define CONFIG_ICACHE_ON
 #define CONFIG_DCACHE_ON

 /* Define where the uboot will be loaded by on-chip boot rom */
 #define APP_ENTRY 0x00001000

 /* CONFIG_CLKIN_HZ is any value in Hz				*/
 #define CONFIG_CLKIN_HZ		27000000
 /* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN	*/
 /*						    1=CLKIN/2	*/
 #define CONFIG_CLKIN_HALF	0
 /* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass	*/
 /*						 1=bypass PLL	*/
 #define CONFIG_PLL_BYPASS	0
 /* CONFIG_VCO_MULT controls what the multiplier of the PLL is.	*/
 /* Values can range from 1-64					*/
 #define CONFIG_VCO_MULT		22
 /* CONFIG_CCLK_DIV controls what the core clock divider is	*/
 /* Values can be 1, 2, 4, or 8 ONLY				*/
 #define CONFIG_CCLK_DIV		1
 /* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
 /* Values can range from 1-15					*/
 #define CONFIG_SCLK_DIV		5
 /* CONFIG_SPI_BAUD controls the SPI peripheral clock divider	*/
 /* Values can range from 2-65535				*/
 /* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD)			*/
 #define CONFIG_SPI_BAUD		2
 #define CONFIG_SPI_BAUD_INITBLOCK	4

 #if ( CONFIG_CLKIN_HALF == 0 )
 #define CONFIG_VCO_HZ		( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
 #else
 #define CONFIG_VCO_HZ		(( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
 #endif

 #if (CONFIG_PLL_BYPASS == 0)
 #define CONFIG_CCLK_HZ		( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
 #define CONFIG_SCLK_HZ		( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
 #else
 #define CONFIG_CCLK_HZ		CONFIG_CLKIN_HZ
 #define CONFIG_SCLK_HZ		CONFIG_CLKIN_HZ
 #endif

 #define CONFIG_MEM_SIZE		32	/* 128, 64, 32, 16 */
 #define CONFIG_MEM_ADD_WDTH	9	/* 8, 9, 10, 11    */
 #define CONFIG_MEM_MT48LC16M16A2TG_75	1

 #define CONFIG_LOADS_ECHO	1


 #define CONFIG_COMMANDS			(CONFIG_CMD_DFL	| \
 					 CFG_CMD_PING	| \
 					 CFG_CMD_ELF	| \
 					 CFG_CMD_I2C	| \
 					 CFG_CMD_JFFS2	| \
 					 CFG_CMD_DATE)
 #define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"

 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>

 #define	CFG_PROMPT		"ezkit> "	/* Monitor Command Prompt */
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define	CFG_CBSIZE		1024	/* Console I/O Buffer Size */
 #else
 #define	CFG_CBSIZE		256	/* Console I/O Buffer Size */
 #endif
 #define	CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
 #define	CFG_MAXARGS		16	/* max number of command args */
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
 #define CFG_MEMTEST_START	0x00000000	/* memtest works on */
 #define CFG_MEMTEST_END		( (CONFIG_MEM_SIZE - 1) * 1024 * 1024)	/* 1 ... 31 MB in DRAM */
 #define	CFG_LOAD_ADDR		0x01000000	/* default load address */
 #define	CFG_HZ			1000	/* decrementer freq: 10 ms ticks */
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 #define	CFG_SDRAM_BASE		0x00000000
 #define CFG_MAX_RAM_SIZE	(CONFIG_MEM_SIZE * 1024 * 1024)
 #define CFG_FLASH_BASE		0x20000000

 #define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CFG_MONITOR_BASE	(CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
 #define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 #define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
 #define CFG_GBL_DATA_SIZE	0x4000
 #define CFG_GBL_DATA_ADDR	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
 #define CONFIG_STACKBASE	(CFG_GBL_DATA_ADDR  - 4)

 #define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 #define CFG_FLASH0_BASE		0x20000000
 #define CFG_FLASH1_BASE		0x20200000
 #define CFG_FLASH2_BASE		0x20280000
 #define CFG_MAX_FLASH_BANKS	3	/* max number of memory banks */
 #define CFG_MAX_FLASH_SECT	40	/* max number of sectors on one chip */

 #define	CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_ADDR		0x20020000
 #define	CFG_ENV_SECT_SIZE	0x10000	/* Total Size of Environment Sector */

 /* JFFS Partition offset set  */
 #define CFG_JFFS2_FIRST_BANK	0
 #define CFG_JFFS2_NUM_BANKS	1
 /* 512k reserved for u-boot */
 #define CFG_JFFS2_FIRST_SECTOR	11


 /*
  * Stack sizes
  */
 #define CONFIG_STACKSIZE	(128*1024)	/* regular stack */

 #define POLL_MODE		1
 #define FLASH_TOT_SECT		40
 #define FLASH_SIZE		0x220000
 #define CFG_FLASH_SIZE		0x220000

 /*
  * Initialize PSD4256 registers for using I2C
  */
 #define	CONFIG_MISC_INIT_R

 /*
  * I2C settings
  * By default PF1 is used as SDA and PF0 as SCL on the Stamp board
  */
 #define CONFIG_SOFT_I2C		1	/* I2C bit-banged */
 /*
  * Software (bit-bang) I2C driver configuration
  */
 #define PF_SCL			PF0
 #define PF_SDA			PF1

 #define I2C_INIT		(*pFIO_DIR |=  PF_SCL); asm("ssync;")
 #define I2C_ACTIVE		(*pFIO_DIR |=  PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
 #define I2C_TRISTATE		(*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
 #define I2C_READ		((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
 #define I2C_SDA(bit)	if(bit) { \
 				*pFIO_FLAG_S = PF_SDA; \
 				asm("ssync;"); \
 				} \
 			else    { \
 				*pFIO_FLAG_C = PF_SDA; \
 				asm("ssync;"); \
 				}
 #define I2C_SCL(bit)	if(bit) { \
 				*pFIO_FLAG_S = PF_SCL; \
 				asm("ssync;"); \
 				} \
 			else    { \
 				*pFIO_FLAG_C = PF_SCL; \
 				asm("ssync;"); \
 				}
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */

 #define CFG_I2C_SPEED		50000
 #define CFG_I2C_SLAVE		0xFE

 #define CFG_BOOTM_LEN		0x4000000	/* Large Image Length, set to 64 Meg */

 /* 0xFF, 0x7BB07BB0, 0x22547BB0 */
 /* #define AMGCTLVAL		(AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
 #define AMBCTL0VAL		(B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
 				~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
 #define AMBCTL1VAL		(B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
 				B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
 */
 #define AMGCTLVAL		0xFF
 #define AMBCTL0VAL		0x7BB07BB0
 #define AMBCTL1VAL		0xFFC27BB0

 #define CONFIG_VDSP		1

 #ifdef CONFIG_VDSP
 #define ET_EXEC_VDSP		0x8
 #define SHT_STRTAB_VDSP		0x1
 #define ELFSHDRSIZE_VDSP	0x2C
 #define VDSP_ENTRY_ADDR		0xFFA00000
 #endif

 #endif
	/*
	* U-boot - Configuration file for BF533 EZKIT board
	*/

	#ifndef __CONFIG_EZKIT533_H__
	#define __CONFIG_EZKIT533_H__

	#define CONFIG_BAUDRATE 57600
	#define CONFIG_STAMP 1

	#define CONFIG_BOOTDELAY 5
	#define CFG_AUTOLOAD "no" /rarpb, bootp or dhcp commands will perform only a /

	#define CFG_LONGHELP 1
	#define CONFIG_CMDLINE_EDITING 1
	#define CONFIG_LOADADDR 0x01000000 /* default load address */
	#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
	/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */

	#define CONFIG_DRIVER_SMC91111 1
	#define CONFIG_SMC91111_BASE 0x20310300

	#if 0
	#define CONFIG_MII
	#define CFG_DISCOVER_PHY
	#endif

	#define CONFIG_RTC_BFIN 1
	#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */

	/*
	* Boot Mode Set
	* Blackfin can support several boot modes
	*/
	#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
	#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
	#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
	/* Define the boot mode */
	#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
	/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */

	#define CONFIG_PANIC_HANG 1

	#define ADSP_BF531 0x31
	#define ADSP_BF532 0x32
	#define ADSP_BF533 0x33
	#define BFIN_CPU ADSP_BF533

	/* This sets the default state of the cache on U-Boot's boot */
	#define CONFIG_ICACHE_ON
	#define CONFIG_DCACHE_ON

	/* Define where the uboot will be loaded by on-chip boot rom */
	#define APP_ENTRY 0x00001000

	/* CONFIG_CLKIN_HZ is any value in Hz */
	#define CONFIG_CLKIN_HZ 27000000
	/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
	/* 1=CLKIN/2 */
	#define CONFIG_CLKIN_HALF 0
	/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
	/* 1=bypass PLL */
	#define CONFIG_PLL_BYPASS 0
	/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
	/* Values can range from 1-64 */
	#define CONFIG_VCO_MULT 22
	/* CONFIG_CCLK_DIV controls what the core clock divider is */
	/* Values can be 1, 2, 4, or 8 ONLY */
	#define CONFIG_CCLK_DIV 1
	/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
	/* Values can range from 1-15 */
	#define CONFIG_SCLK_DIV 5
	/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
	/* Values can range from 2-65535 */
	/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
	#define CONFIG_SPI_BAUD 2
	#define CONFIG_SPI_BAUD_INITBLOCK 4

	#if ( CONFIG_CLKIN_HALF == 0 )
	#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
	#else
	#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
	#endif

	#if (CONFIG_PLL_BYPASS == 0)
	#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
	#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
	#else
	#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
	#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
	#endif

	#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
	#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
	#define CONFIG_MEM_MT48LC16M16A2TG_75 1

	#define CONFIG_LOADS_ECHO 1


	#define CONFIG_COMMANDS (CONFIG_CMD_DFL \| \
	CFG_CMD_PING \| \
	CFG_CMD_ELF \| \
	CFG_CMD_I2C \| \
	CFG_CMD_JFFS2 \| \
	CFG_CMD_DATE)
	#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"

	/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
	#include <cmd_confdefs.h>

	#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
	#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
	#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
	#define CFG_LOAD_ADDR 0x01000000 /* default load address */
	#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
	#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
	#define CFG_SDRAM_BASE 0x00000000
	#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
	#define CFG_FLASH_BASE 0x20000000

	#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
	#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
	#define CFG_GBL_DATA_SIZE 0x4000
	#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
	#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)

	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
	#define CFG_FLASH0_BASE 0x20000000
	#define CFG_FLASH1_BASE 0x20200000
	#define CFG_FLASH2_BASE 0x20280000
	#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
	#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */

	#define CFG_ENV_IS_IN_FLASH 1
	#define CFG_ENV_ADDR 0x20020000
	#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */

	/* JFFS Partition offset set */
	#define CFG_JFFS2_FIRST_BANK 0
	#define CFG_JFFS2_NUM_BANKS 1
	/* 512k reserved for u-boot */
	#define CFG_JFFS2_FIRST_SECTOR 11


	/*
	* Stack sizes
	*/
	#define CONFIG_STACKSIZE (1281024) / regular stack */

	#define POLL_MODE 1
	#define FLASH_TOT_SECT 40
	#define FLASH_SIZE 0x220000
	#define CFG_FLASH_SIZE 0x220000

	/*
	* Initialize PSD4256 registers for using I2C
	*/
	#define CONFIG_MISC_INIT_R

	/*
	* I2C settings
	* By default PF1 is used as SDA and PF0 as SCL on the Stamp board
	*/
	#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
	/*
	* Software (bit-bang) I2C driver configuration
	*/
	#define PF_SCL PF0
	#define PF_SDA PF1

	#define I2C_INIT (*pFIO_DIR \|= PF_SCL); asm("ssync;")
	#define I2C_ACTIVE (pFIO_DIR \|= PF_SDA); pFIO_INEN &= ~PF_SDA; asm("ssync;")
	#define I2C_TRISTATE (pFIO_DIR &= ~PF_SDA); pFIO_INEN \|= PF_SDA; asm("ssync;")
	#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
	#define I2C_SDA(bit) if(bit) { \
	*pFIO_FLAG_S = PF_SDA; \
	asm("ssync;"); \
	} \
	else { \
	*pFIO_FLAG_C = PF_SDA; \
	asm("ssync;"); \
	}
	#define I2C_SCL(bit) if(bit) { \
	*pFIO_FLAG_S = PF_SCL; \
	asm("ssync;"); \
	} \
	else { \
	*pFIO_FLAG_C = PF_SCL; \
	asm("ssync;"); \
	}
	#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */

	#define CFG_I2C_SPEED 50000
	#define CFG_I2C_SLAVE 0xFE

	#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */

	/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
	/* #define AMGCTLVAL (AMBEN_P0 \| AMBEN_P1 \| AMBEN_P2 \| AMCKEN)
	#define AMBCTL0VAL (B1WAT_7 \| B1RAT_11 \| B1HT_2 \| B1ST_3 \| B1TT_4 \| ~B1RDYPOL \| \
	~B1RDYEN \| B0WAT_7 \| B0RAT_11 \| B0HT_2 \| B0ST_3 \| B0TT_4 \| ~B0RDYPOL \| ~B0RDYEN)
	#define AMBCTL1VAL (B3WAT_2 \| B3RAT_2 \| B3HT_1 \| B3ST_1 \| B3TT_4 \| B3RDYPOL \| ~B3RDYEN \| \
	B2WAT_7 \| B2RAT_11 \| B2HT_2 \| B2ST_3 \| B2TT_4 \| ~B2RDYPOL \| ~B2RDYEN)
	*/
	#define AMGCTLVAL 0xFF
	#define AMBCTL0VAL 0x7BB07BB0
	#define AMBCTL1VAL 0xFFC27BB0

	#define CONFIG_VDSP 1

	#ifdef CONFIG_VDSP
	#define ET_EXEC_VDSP 0x8
	#define SHT_STRTAB_VDSP 0x1
	#define ELFSHDRSIZE_VDSP 0x2C
	#define VDSP_ENTRY_ADDR 0xFFA00000
	#endif

	#endif