| /* |
| * (C) Copyright 2010 |
| * Ilko Iliev <iliev@ronetix.at> |
| * Asen Dimov <dimov@ronetix.at> |
| * Ronetix GmbH <www.ronetix.at> |
| * |
| * (C) Copyright 2007-2008 |
| * Stelian Pop <stelian@popies.net> |
| * Lead Tech Design <www.leadtechdesign.com> |
| * |
| * Configuation settings for the PM9G45 board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * SoC must be defined first, before hardware.h is included. |
| * In this case SoC is defined in boards.cfg. |
| */ |
| #include <asm/hardware.h> |
| |
| #define CONFIG_SYS_GENERIC_BOARD |
| |
| #define CONFIG_PM9G45 1 /* It's an Ronetix PM9G45 */ |
| #define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9G45" |
| |
| #define MACH_TYPE_PM9G45 2672 |
| #define CONFIG_MACH_TYPE MACH_TYPE_PM9G45 |
| |
| /* ARM asynchronous clock */ |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ |
| #define CONFIG_SYS_TEXT_BASE 0x73f00000 |
| |
| #define CONFIG_ARCH_CPU_INIT |
| |
| #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS 1 |
| #define CONFIG_INITRD_TAG 1 |
| |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_BOARD_EARLY_INIT_F |
| |
| /* |
| * Hardware drivers |
| */ |
| #define CONFIG_AT91_GPIO 1 |
| #define CONFIG_ATMEL_USART 1 |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID ATMEL_ID_SYS |
| |
| #define CONFIG_SYS_USE_NANDFLASH 1 |
| |
| /* LED */ |
| #define CONFIG_AT91_LED |
| #define CONFIG_RED_LED GPIO_PIN_PD(31) /* this is the user1 led */ |
| #define CONFIG_GREEN_LED GPIO_PIN_PD(0) /* this is the user2 led */ |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE 1 |
| #define CONFIG_BOOTP_BOOTPATH 1 |
| #define CONFIG_BOOTP_GATEWAY 1 |
| #define CONFIG_BOOTP_HOSTNAME 1 |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| #undef CONFIG_CMD_FPGA |
| #undef CONFIG_CMD_IMLS |
| |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_PING 1 |
| #define CONFIG_CMD_DHCP 1 |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_CMD_USB 1 |
| |
| #define CONFIG_CMD_JFFS2 1 |
| #define CONFIG_JFFS2_CMDLINE 1 |
| #define CONFIG_JFFS2_NAND 1 |
| #define CONFIG_JFFS2_DEV "nand0" /* NAND dev jffs2 lives on */ |
| #define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ |
| #define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition */ |
| |
| /* SDRAM */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define PHYS_SDRAM 0x70000000 |
| #define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */ |
| |
| /* NOR flash, not available */ |
| #define CONFIG_SYS_NO_FLASH 1 |
| #undef CONFIG_CMD_FLASH |
| |
| /* NAND flash */ |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_NAND_ATMEL |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE 0x40000000 |
| #define CONFIG_SYS_NAND_DBW_8 1 |
| /* our ALE is AD21 */ |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) |
| /* our CLE is AD22 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) |
| #define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) |
| #define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PD(3) |
| |
| #endif |
| |
| /* Ethernet */ |
| #define CONFIG_MACB 1 |
| #define CONFIG_RMII 1 |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #define CONFIG_RESET_PHY_R 1 |
| |
| /* USB */ |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_ATMEL_CLK_SEL_UPLL |
| #define CONFIG_USB_OHCI_NEW 1 |
| #define CONFIG_DOS_PARTITION 1 |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */ |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 |
| #define CONFIG_USB_STORAGE 1 |
| |
| /* board specific(not enough SRAM) */ |
| #define CONFIG_AT91SAM9G45_LCD_BASE PHYS_SDRAM + 0xE00000 |
| |
| #define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM + 0x2000000 /* load addr */ |
| |
| #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM |
| #define CONFIG_SYS_MEMTEST_END CONFIG_AT91SAM9G45_LCD_BASE |
| |
| /* bootstrap + u-boot + env + linux in nandflash */ |
| #define CONFIG_ENV_IS_IN_NAND 1 |
| #define CONFIG_ENV_OFFSET 0x60000 |
| #define CONFIG_ENV_OFFSET_REDUND 0x80000 |
| #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ |
| #define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm" |
| #define CONFIG_BOOTARGS "fbcon=rotate:3 console=tty0 " \ |
| "console=ttyS0,115200 " \ |
| "root=/dev/mtdblock4 " \ |
| "mtdparts=atmel_nand:128k(bootstrap)ro," \ |
| "256k(uboot)ro,1664k(env)," \ |
| "2M(linux)ro,-(root) rw " \ |
| "rootfstype=jffs2" |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_SYS_PROMPT "U-Boot> " |
| #define CONFIG_SYS_CBSIZE 256 |
| #define CONFIG_SYS_MAXARGS 16 |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ |
| sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_CMDLINE_EDITING 1 |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\ |
| 0x1000) |
| |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ |
| GENERATED_GBL_DATA_SIZE) |
| |
| #endif |