| /* |
| * Copyright 2009-2011 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * mpc8569mds board configuration file |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_MPC8569 1 /* MPC8569 specific */ |
| #define CONFIG_MPC8569MDS 1 /* MPC8569MDS board specific */ |
| |
| #define CONFIG_FSL_ELBC 1 /* Has Enhance localbus controller */ |
| |
| #define CONFIG_SYS_SRIO |
| #define CONFIG_SRIO1 /* SRIO port 1 */ |
| |
| #define CONFIG_PCI 1 /* Disable PCI/PCIE */ |
| #define CONFIG_PCIE1 1 /* PCIE controller */ |
| #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ |
| #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ |
| #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ |
| #define CONFIG_QE /* Enable QE */ |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ |
| |
| #ifndef __ASSEMBLY__ |
| extern unsigned long get_clock_freq(void); |
| #endif |
| /* Replace a call to get_clock_freq (after it is implemented)*/ |
| #define CONFIG_SYS_CLK_FREQ 66666666 |
| #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ |
| |
| #ifdef CONFIG_ATM |
| #define CONFIG_PQ_MDS_PIB |
| #define CONFIG_PQ_MDS_PIB_ATM |
| #endif |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #define CONFIG_BTB /* toggle branch predition */ |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xfff80000 |
| #endif |
| |
| #ifndef CONFIG_SYS_MONITOR_BASE |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #endif |
| |
| /* |
| * Only possible on E500 Version 2 or newer cores. |
| */ |
| #define CONFIG_ENABLE_36BIT_PHYS 1 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ |
| #define CONFIG_BOARD_EARLY_INIT_R 1 |
| #define CONFIG_HWCONFIG |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| |
| /* |
| * Config the L2 Cache as L2 SRAM |
| */ |
| #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 |
| #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR |
| #define CONFIG_SYS_L2_SIZE (512 << 10) |
| #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) |
| |
| #define CONFIG_SYS_CCSRBAR 0xe0000000 |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| |
| #if defined(CONFIG_NAND_SPL) |
| #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE |
| #endif |
| |
| /* DDR Setup */ |
| #define CONFIG_SYS_FSL_DDR3 |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ |
| #define CONFIG_DDR_SPD |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ |
| |
| #define CONFIG_MEM_INIT_VALUE 0xDeadBeef |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| /* DDR is system memory*/ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 1 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| |
| /* I2C addresses of SPD EEPROMs */ |
| #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ |
| |
| /* These are used when DDR doesn't use SPD. */ |
| #define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 |
| #define CONFIG_SYS_DDR_TIMING_3 0x00020000 |
| #define CONFIG_SYS_DDR_TIMING_0 0x00330004 |
| #define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644 |
| #define CONFIG_SYS_DDR_TIMING_2 0x002888D0 |
| #define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 |
| #define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 |
| #define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521 |
| #define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 |
| #define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000 |
| #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef |
| #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000 |
| #define CONFIG_SYS_DDR_TIMING_4 0x00220001 |
| #define CONFIG_SYS_DDR_TIMING_5 0x03402400 |
| #define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 |
| #define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604 |
| #define CONFIG_SYS_DDR_CDR_1 0x80040000 |
| #define CONFIG_SYS_DDR_CDR_2 0x00000000 |
| #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 |
| #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 |
| #define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */ |
| #define CONFIG_SYS_DDR_CONTROL2 0x24400000 |
| |
| #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d |
| #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 |
| #define CONFIG_SYS_DDR_SBE 0x00010000 |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| /* |
| * Local Bus Definitions |
| */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| |
| #define CONFIG_SYS_BCSR_BASE 0xf8000000 |
| #define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE |
| |
| /*Chip select 0 - Flash*/ |
| #define CONFIG_FLASH_BR_PRELIM 0xfe000801 |
| #define CONFIG_FLASH_OR_PRELIM 0xfe000ff7 |
| |
| /*Chip select 1 - BCSR*/ |
| #define CONFIG_SYS_BR1_PRELIM 0xf8000801 |
| #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 |
| |
| /*Chip select 4 - PIB*/ |
| #define CONFIG_SYS_BR4_PRELIM 0xf8008801 |
| #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 |
| |
| /*Chip select 5 - PIB*/ |
| #define CONFIG_SYS_BR5_PRELIM 0xf8010801 |
| #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #undef CONFIG_SYS_RAMBOOT |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| |
| /* Chip select 3 - NAND */ |
| #ifndef CONFIG_NAND_SPL |
| #define CONFIG_SYS_NAND_BASE 0xFC000000 |
| #else |
| #define CONFIG_SYS_NAND_BASE 0xFFF00000 |
| #endif |
| |
| /* NAND boot: 4K NAND loader config */ |
| #define CONFIG_SYS_NAND_SPL_SIZE 0x1000 |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) |
| #define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) |
| #define CONFIG_SYS_NAND_U_BOOT_START \ |
| (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS (0) |
| #define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) |
| #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) |
| |
| #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_NAND_FSL_ELBC 1 |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) |
| #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ |
| | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ |
| | BR_PS_8 /* Port Size = 8 bit */ \ |
| | BR_MS_FCM /* MSEL = FCM */ \ |
| | BR_V) /* valid */ |
| #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ |
| | OR_FCM_CSCT \ |
| | OR_FCM_CST \ |
| | OR_FCM_CHT \ |
| | OR_FCM_SCY_1 \ |
| | OR_FCM_TRLX \ |
| | OR_FCM_EHTR) |
| |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ |
| #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ |
| #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ |
| |
| #define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ |
| #define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */ |
| #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ |
| #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ |
| |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| #ifdef CONFIG_NAND_SPL |
| #define CONFIG_NS16550_MIN_FUNCTIONS |
| #endif |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* Use the HUSH parser*/ |
| #define CONFIG_SYS_HUSH_PARSER |
| #ifdef CONFIG_SYS_HUSH_PARSER |
| #endif |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 |
| #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } |
| |
| /* |
| * I2C2 EEPROM |
| */ |
| #define CONFIG_ID_EEPROM |
| #ifdef CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #endif |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_BUS_NUM 1 |
| |
| #define PLPPAR1_I2C_BIT_MASK 0x0000000F |
| #define PLPPAR1_I2C2_VAL 0x00000000 |
| #define PLPPAR1_ESDHC_VAL 0x0000000A |
| #define PLPDIR1_I2C_BIT_MASK 0x0000000F |
| #define PLPDIR1_I2C2_VAL 0x0000000F |
| #define PLPDIR1_ESDHC_VAL 0x00000006 |
| #define PLPPAR1_UART0_BIT_MASK 0x00000fc0 |
| #define PLPPAR1_ESDHC_4BITS_VAL 0x00000a80 |
| #define PLPDIR1_UART0_BIT_MASK 0x00000fc0 |
| #define PLPDIR1_ESDHC_4BITS_VAL 0x00000a80 |
| |
| /* |
| * General PCI |
| * Memory Addresses are mapped 1-1. I/O is mapped from 0 |
| */ |
| #define CONFIG_SYS_PCIE1_NAME "Slot" |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ |
| |
| #define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000 |
| #define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000 |
| #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS |
| #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ |
| |
| #ifdef CONFIG_QE |
| /* |
| * QE UEC ethernet configuration |
| */ |
| #define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */ |
| #undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */ |
| |
| #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) |
| #define CONFIG_UEC_ETH |
| #define CONFIG_ETHPRIME "UEC0" |
| #define CONFIG_PHY_MODE_NEED_CHANGE |
| |
| #define CONFIG_UEC_ETH1 /* GETH1 */ |
| #define CONFIG_HAS_ETH0 |
| |
| #ifdef CONFIG_UEC_ETH1 |
| #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ |
| #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE |
| #if defined(CONFIG_SYS_UCC_RGMII_MODE) |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 |
| #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR 7 |
| #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID |
| #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 |
| #elif defined(CONFIG_SYS_UCC_RMII_MODE) |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */ |
| #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */ |
| #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII |
| #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 |
| #endif /* CONFIG_SYS_UCC_RGMII_MODE */ |
| #endif /* CONFIG_UEC_ETH1 */ |
| |
| #define CONFIG_UEC_ETH2 /* GETH2 */ |
| #define CONFIG_HAS_ETH1 |
| |
| #ifdef CONFIG_UEC_ETH2 |
| #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ |
| #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE |
| #if defined(CONFIG_SYS_UCC_RGMII_MODE) |
| #define CONFIG_SYS_UEC2_TX_CLK QE_CLK17 |
| #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC2_PHY_ADDR 1 |
| #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID |
| #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 |
| #elif defined(CONFIG_SYS_UCC_RMII_MODE) |
| #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */ |
| #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */ |
| #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII |
| #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 |
| #endif /* CONFIG_SYS_UCC_RGMII_MODE */ |
| #endif /* CONFIG_UEC_ETH2 */ |
| |
| #define CONFIG_UEC_ETH3 /* GETH3 */ |
| #define CONFIG_HAS_ETH2 |
| |
| #ifdef CONFIG_UEC_ETH3 |
| #define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */ |
| #define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE |
| #if defined(CONFIG_SYS_UCC_RGMII_MODE) |
| #define CONFIG_SYS_UEC3_TX_CLK QE_CLK12 |
| #define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC3_PHY_ADDR 2 |
| #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID |
| #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000 |
| #elif defined(CONFIG_SYS_UCC_RMII_MODE) |
| #define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */ |
| #define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */ |
| #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII |
| #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100 |
| #endif /* CONFIG_SYS_UCC_RGMII_MODE */ |
| #endif /* CONFIG_UEC_ETH3 */ |
| |
| #define CONFIG_UEC_ETH4 /* GETH4 */ |
| #define CONFIG_HAS_ETH3 |
| |
| #ifdef CONFIG_UEC_ETH4 |
| #define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */ |
| #define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE |
| #if defined(CONFIG_SYS_UCC_RGMII_MODE) |
| #define CONFIG_SYS_UEC4_TX_CLK QE_CLK17 |
| #define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC4_PHY_ADDR 3 |
| #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID |
| #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000 |
| #elif defined(CONFIG_SYS_UCC_RMII_MODE) |
| #define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */ |
| #define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */ |
| #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII |
| #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100 |
| #endif /* CONFIG_SYS_UCC_RGMII_MODE */ |
| #endif /* CONFIG_UEC_ETH4 */ |
| |
| #undef CONFIG_UEC_ETH6 /* GETH6 */ |
| #define CONFIG_HAS_ETH5 |
| |
| #ifdef CONFIG_UEC_ETH6 |
| #define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */ |
| #define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC6_PHY_ADDR 4 |
| #define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII |
| #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000 |
| #endif /* CONFIG_UEC_ETH6 */ |
| |
| #undef CONFIG_UEC_ETH8 /* GETH8 */ |
| #define CONFIG_HAS_ETH7 |
| |
| #ifdef CONFIG_UEC_ETH8 |
| #define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */ |
| #define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE |
| #define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH |
| #define CONFIG_SYS_UEC8_PHY_ADDR 6 |
| #define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII |
| #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000 |
| #endif /* CONFIG_UEC_ETH8 */ |
| |
| #endif /* CONFIG_QE */ |
| |
| #if defined(CONFIG_PCI) |
| |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| #define CONFIG_E1000 /* Define e1000 pci Ethernet card */ |
| |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| /* |
| * Environment |
| */ |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* QE microcode/firmware address */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NOR |
| #define CONFIG_SYS_QE_FW_ADDR 0xfff00000 |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_SETEXPR |
| #define CONFIG_CMD_REGINFO |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #define CONFIG_MMC 1 |
| |
| #ifdef CONFIG_MMC |
| #define CONFIG_FSL_ESDHC |
| #define CONFIG_FSL_ESDHC_PIN_MUX |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #define CONFIG_CMD_MMC |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_FAT |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| /* Boot Argument Buffer Size */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_HOSTNAME mpc8569mds |
| #define CONFIG_ROOTPATH "/nfsroot" |
| #define CONFIG_BOOTFILE "your.uImage" |
| |
| #define CONFIG_SERVERIP 192.168.1.1 |
| #define CONFIG_GATEWAYIP 192.168.1.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| |
| #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ |
| |
| #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=600000\0" \ |
| "ramdiskfile=your.ramdisk.u-boot\0" \ |
| "fdtaddr=400000\0" \ |
| "fdtfile=your.fdt.dtb\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs\0" \ |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "run nfsargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "run ramargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "bootm $loadaddr $ramdiskaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |