blob: e256eeb6686805131a1a5cb5aaf992df1cf6de1e [file] [log] [blame]
if ARCH_UNIPHIER
config SYS_CONFIG_NAME
default "uniphier"
config ARCH_UNIPHIER_32BIT
bool
select CPU_V7
config ARCH_UNIPHIER_64BIT
bool
select ARM64
select SPL_SEPARATE_BSS
select ARMV8_MULTIENTRY
choice
prompt "UniPhier SoC select"
default ARCH_UNIPHIER_PRO4
config ARCH_UNIPHIER_SLD3
bool "UniPhier PH1-sLD3 SoC"
select ARCH_UNIPHIER_32BIT
config ARCH_UNIPHIER_LD4_SLD8
bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
select ARCH_UNIPHIER_32BIT
config ARCH_UNIPHIER_PRO4
bool "UniPhier PH1-Pro4 SoC"
select ARCH_UNIPHIER_32BIT
config ARCH_UNIPHIER_PRO5_PXS2_LD6B
bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
select ARCH_UNIPHIER_32BIT
config ARCH_UNIPHIER_LD11
bool "UniPhier PH1-LD11 SoC"
select ARCH_UNIPHIER_64BIT
config ARCH_UNIPHIER_LD20
bool "UniPhier PH1-LD20 SoC"
select ARCH_UNIPHIER_64BIT
select OF_BOARD_SETUP
endchoice
config ARCH_UNIPHIER_LD4
bool "Enable UniPhier PH1-LD4 SoC support"
depends on ARCH_UNIPHIER_LD4_SLD8
default y
config ARCH_UNIPHIER_SLD8
bool "Enable UniPhier PH1-sLD8 SoC support"
depends on ARCH_UNIPHIER_LD4_SLD8
default y
config ARCH_UNIPHIER_PRO5
bool "Enable UniPhier PH1-Pro5 SoC support"
depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
default y
config ARCH_UNIPHIER_PXS2
bool "Enable UniPhier ProXstream2 SoC support"
depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
default y
config ARCH_UNIPHIER_LD6B
bool "Enable UniPhier PH1-LD6b SoC support"
depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
default y
config MICRO_SUPPORT_CARD
bool "Use Micro Support Card"
help
This option provides support for the expansion board, available
on some UniPhier reference boards.
Say Y to use the on-board UART, Ether, LED devices.
config CMD_PINMON
bool "Enable boot mode pins monitor command"
default y
help
The command "pinmon" shows the state of the boot mode pins.
The boot mode pins are latched when the system reset is deasserted
and determine which device the system should load a boot image from.
config CMD_DDRPHY_DUMP
bool "Enable dump command of DDR PHY parameters"
depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
default y
help
The command "ddrphy" shows the resulting parameters of DDR PHY
training; it is useful for the evaluation of DDR PHY training.
config CMD_DDRMPHY_DUMP
bool "Enable dump command of DDR Multi PHY parameters"
depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
default y
help
The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
training; it is useful for the evaluation of DDR Multi PHY training.
endif