| CONFIG_ARM=y |
| CONFIG_ARCH_CPU_INIT=y |
| CONFIG_ARCH_AT91=y |
| CONFIG_SYS_TEXT_BASE=0x0000000 |
| CONFIG_SYS_MALLOC_LEN=0x50000 |
| CONFIG_TARGET_AT91SAM9263EK=y |
| CONFIG_ATMEL_LEGACY=y |
| CONFIG_SYS_USE_NORFLASH=y |
| CONFIG_NR_DRAM_BANKS=1 |
| CONFIG_ENV_SIZE=0x10000 |
| CONFIG_ENV_SECT_SIZE=0x10000 |
| CONFIG_DM_GPIO=y |
| CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek" |
| CONFIG_SYS_PROMPT="U-Boot> " |
| CONFIG_DEBUG_UART_BASE=0xffffee00 |
| CONFIG_DEBUG_UART_CLOCK=100000000 |
| CONFIG_DEBUG_UART_BOARD_INIT=y |
| CONFIG_SYS_LOAD_ADDR=0x22000000 |
| CONFIG_ENV_ADDR=0x107E0000 |
| CONFIG_DEBUG_UART=y |
| CONFIG_SYS_MONITOR_BASE=0x10000000 |
| CONFIG_BOOTDELAY=3 |
| CONFIG_SYS_CONSOLE_IS_IN_ENV=y |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_RESET_PHY_R=y |
| CONFIG_HUSH_PARSER=y |
| CONFIG_SYS_CBSIZE=256 |
| CONFIG_SYS_PBSIZE=281 |
| # CONFIG_CMD_BDI is not set |
| CONFIG_CMD_BOOTZ=y |
| # CONFIG_CMD_IMI is not set |
| # CONFIG_CMD_LOADS is not set |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_NAND=y |
| # CONFIG_CMD_SOURCE is not set |
| # CONFIG_CMD_SETEXPR is not set |
| CONFIG_CMD_DHCP=y |
| CONFIG_BOOTP_BOOTFILESIZE=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_FAT=y |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_IS_IN_FLASH=y |
| CONFIG_SYS_REDUNDAND_ENVIRONMENT=y |
| CONFIG_ENV_ADDR_REDUND=0x107D0000 |
| CONFIG_CLK=y |
| CONFIG_CLK_AT91=y |
| CONFIG_AT91_GPIO=y |
| CONFIG_GENERIC_ATMEL_MCI=y |
| CONFIG_MTD=y |
| CONFIG_MTD_NOR_FLASH=y |
| CONFIG_FLASH_CFI_DRIVER=y |
| CONFIG_SYS_FLASH_CFI=y |
| CONFIG_SYS_MAX_FLASH_SECT=256 |
| CONFIG_MTD_RAW_NAND=y |
| CONFIG_NAND_ATMEL=y |
| CONFIG_DM_SPI_FLASH=y |
| CONFIG_SPI_FLASH_ATMEL=y |
| CONFIG_SPI_FLASH_DATAFLASH=y |
| CONFIG_MACB=y |
| CONFIG_PINCTRL=y |
| CONFIG_PINCTRL_AT91=y |
| CONFIG_DM_SERIAL=y |
| CONFIG_DEBUG_UART_ANNOUNCE=y |
| CONFIG_ATMEL_USART=y |
| CONFIG_SPI=y |
| CONFIG_DM_SPI=y |
| CONFIG_TIMER=y |
| CONFIG_ATMEL_PIT_TIMER=y |
| CONFIG_USB=y |
| CONFIG_SYS_USB_OHCI_SLOT_NAME="at91sam9263" |
| CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS=2 |
| CONFIG_USB_ATMEL=y |
| CONFIG_ATMEL_LCD_BGR555=y |