include/configs/cobra5272.h - github/trini/u-boot - Gitiles

 /*
  * Configuation settings for the Sentec Cobra Board.
  *
  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /* ---
  * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
  * Date: 2004-03-29
  * Author: Florian Schlote
  *
  * For a description of configuration options please refer also to the
  * general u-boot-1.x.x/README file
  * ---
  */

 /* ---
  * board/config.h - configuration options, board specific
  * ---
  */

 #ifndef _CONFIG_COBRA5272_H
 #define _CONFIG_COBRA5272_H

 /* ---
  * Defines processor clock - important for correct timings concerning serial
  * interface etc.
  * ---
  */

 #define CONFIG_SYS_CLK			66000000
 #define CONFIG_SYS_SDRAM_SIZE		16		/* SDRAM size in MB */

 /* ---
  * Enable use of Ethernet
  * ---
  */
 #define CONFIG_MCFFEC

 /* Enable Dma Timer */
 #define CONFIG_MCFTMR

 /* ---
  * Define baudrate for UART1 (console output, tftp, ...)
  * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
  * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
  * interface
  * ---
  */

 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT		(0)

 /* ---
  * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
  * timeout acc. to your needs
  * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
  * for 10 sec
  * ---
  */

 #if 0
 #define CONFIG_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT 10000	/* timeout in milliseconds */
 #endif

 /* ---
  * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
  * bootloader residing in flash ('chainloading'); if you want to use
  * chainloading or want to compile a u-boot binary that can be loaded into
  * RAM via BDM set
  *	"#if 0" to "#if 1"
  * You will need a first stage bootloader then, e. g. colilo or a working BDM
  * cable (Background Debug Mode)
  *
  * Setting #if 0: u-boot will start from flash and relocate itself to RAM
  *
  * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE
  * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
  *
  * ---
  */

 #if 0
 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
 #endif

 /* ---
  * Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
  * ---
  */

 #ifndef CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_ENV_OFFSET		0x4000
 #define CONFIG_ENV_SECT_SIZE	0x2000
 #else
 #define CONFIG_ENV_ADDR		0xffe04000
 #define CONFIG_ENV_SECT_SIZE	0x2000
 #endif

 #define LDS_BOARD_TEXT \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	env/embedded.o(.text);

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 /*
  * Command line configuration.
  */

 #ifdef CONFIG_MCFFEC
 #	define CONFIG_MII		1
 #	define CONFIG_MII_INIT		1
 #	define CONFIG_SYS_DISCOVER_PHY
 #	define CONFIG_SYS_RX_ETH_BUFFER	8
 #	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN

 #	define CONFIG_SYS_FEC0_PINMUX		0
 #	define CONFIG_SYS_FEC0_MIIBASE		CONFIG_SYS_FEC0_IOBASE
 #	define MCFFEC_TOUT_LOOP		50000
 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
 #	ifndef CONFIG_SYS_DISCOVER_PHY
 #		define FECDUPLEX	FULL
 #		define FECSPEED		_100BASET
 #	else
 #		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 #			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 #		endif
 #	endif			/* CONFIG_SYS_DISCOVER_PHY */
 #endif

 /*
  *-----------------------------------------------------------------------------
  * Define user parameters that have to be customized most likely
  *-----------------------------------------------------------------------------
  */

 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/

 /* The following settings will be contained in the environment block ; if you
 want to use a neutral environment all those settings can be manually set in
 u-boot: 'set' command */

 #if 0

 #define CONFIG_BOOTCOMMAND	"bootm 0xffe80000"	/*Autoboto command, please
 enter a valid image address in flash */

 /* User network settings */

 #define CONFIG_IPADDR 192.168.100.2		/* default board IP address */
 #define CONFIG_SERVERIP 192.168.100.1	/* default tftp server IP address */

 #endif

 #define CONFIG_SYS_LOAD_ADDR		0x20000		/*Defines default RAM address
 from which user programs will be started */

 /*---*/

 #define CONFIG_SYS_LONGHELP				/* undef to save memory		*/

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
 #define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 /*
  *-----------------------------------------------------------------------------
  * End of user parameters to be customized
  *-----------------------------------------------------------------------------
  */

 /* ---
  * Defines memory range for test
  * ---
  */

 #define CONFIG_SYS_MEMTEST_START	0x400
 #define CONFIG_SYS_MEMTEST_END		0x380000

 /* ---
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  * ---
  */

 /* ---
  * Base register address
  * ---
  */

 #define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */

 /* ---
  * System Conf. Reg. & System Protection Reg.
  * ---
  */

 #define CONFIG_SYS_SCR			0x0003
 #define CONFIG_SYS_SPR			0xffff

 /* ---
  * Ethernet settings
  * ---
  */

 #define CONFIG_SYS_DISCOVER_PHY
 #define CONFIG_SYS_ENET_BD_BASE	0x780000

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in internal SRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM	*/
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000

 /*
  *-------------------------------------------------------------------------
  * RAM SIZE (is defined above)
  *-----------------------------------------------------------------------
  */

 /* #define CONFIG_SYS_SDRAM_SIZE		16 */

 /*
  *-----------------------------------------------------------------------
  */

 #define CONFIG_SYS_FLASH_BASE		0xffe00000

 #ifdef	CONFIG_MONITOR_IS_IN_RAM
 #define CONFIG_SYS_MONITOR_BASE	0x20000
 #else
 #define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
 #endif

 #define CONFIG_SYS_MONITOR_LEN		0x20000
 #define CONFIG_SYS_MALLOC_LEN		(256 << 10)
 #define CONFIG_SYS_BOOTPARAMS_LEN	64*1024

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
 #define CONFIG_SYS_MAX_FLASH_SECT	11	/* max number of sectors on one chip	*/
 #define CONFIG_SYS_FLASH_ERASE_TOUT	1000	/* flash timeout */

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CONFIG_SYS_CACHELINE_SIZE	16

 #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 8)
 #define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - 4)
 #define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINV | CF_CACR_INVI)
 #define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_SDRAM_BASE | \
 					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 					 CF_ACR_EN | CF_ACR_SM_ALL)
 #define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CINV | \
 					 CF_CACR_DISD | CF_CACR_INVI | \
 					 CF_CACR_CEIB | CF_CACR_DCM | \
 					 CF_CACR_EUSP)

 /*-----------------------------------------------------------------------
  * Memory bank definitions
  *
  * Please refer also to Motorola Coldfire user manual - Chapter XXX
  * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
  */
 #define CONFIG_SYS_BR0_PRELIM		0xFFE00201
 #define CONFIG_SYS_OR0_PRELIM		0xFFE00014

 #define CONFIG_SYS_BR1_PRELIM		0
 #define CONFIG_SYS_OR1_PRELIM		0

 #define CONFIG_SYS_BR2_PRELIM		0
 #define CONFIG_SYS_OR2_PRELIM		0

 #define CONFIG_SYS_BR3_PRELIM		0
 #define CONFIG_SYS_OR3_PRELIM		0

 #define CONFIG_SYS_BR4_PRELIM		0
 #define CONFIG_SYS_OR4_PRELIM		0

 #define CONFIG_SYS_BR5_PRELIM		0
 #define CONFIG_SYS_OR5_PRELIM		0

 #define CONFIG_SYS_BR6_PRELIM		0
 #define CONFIG_SYS_OR6_PRELIM		0

 #define CONFIG_SYS_BR7_PRELIM		0x00000701
 #define CONFIG_SYS_OR7_PRELIM		0xFF00007C

 /*-----------------------------------------------------------------------
  * LED config
  */
 #define	LED_STAT_0	0xffff /*all LEDs off*/
 #define	LED_STAT_1	0xfffe
 #define	LED_STAT_2	0xfffd
 #define	LED_STAT_3	0xfffb
 #define	LED_STAT_4	0xfff7
 #define	LED_STAT_5	0xffef
 #define	LED_STAT_6	0xffdf
 #define	LED_STAT_7	0xff00 /*all LEDs on*/

 /*-----------------------------------------------------------------------
  * Port configuration (GPIO)
  */
 #define CONFIG_SYS_PACNT		0x00000000		/* PortA control reg.: All pins are external
 GPIO*/
 #define CONFIG_SYS_PADDR		0x00FF			/* PortA direction reg.: PA7 to PA0 are outputs
 (1^=output, 0^=input) */
 #define CONFIG_SYS_PADAT		LED_STAT_0		/* PortA value reg.: Turn all LED off */
 #define CONFIG_SYS_PBCNT		0x55554155		/* PortB control reg.: Ethernet/UART
 configuration */
 #define CONFIG_SYS_PBDDR		0x0000			/* PortB direction: All pins configured as inputs */
 #define CONFIG_SYS_PBDAT		0x0000			/* PortB value reg. */
 #define CONFIG_SYS_PDCNT		0x00000000		/* PortD control reg. */

 #endif	/* _CONFIG_COBRA5272_H */
	/*
	* Configuation settings for the Sentec Cobra Board.
	*
	* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/* ---
	* Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
	* Date: 2004-03-29
	* Author: Florian Schlote
	*
	* For a description of configuration options please refer also to the
	* general u-boot-1.x.x/README file
	* ---
	*/

	/* ---
	* board/config.h - configuration options, board specific
	* ---
	*/

	#ifndef _CONFIG_COBRA5272_H
	#define _CONFIG_COBRA5272_H

	/* ---
	* Defines processor clock - important for correct timings concerning serial
	* interface etc.
	* ---
	*/

	#define CONFIG_SYS_CLK 66000000
	#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */

	/* ---
	* Enable use of Ethernet
	* ---
	*/
	#define CONFIG_MCFFEC

	/* Enable Dma Timer */
	#define CONFIG_MCFTMR

	/* ---
	* Define baudrate for UART1 (console output, tftp, ...)
	* default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
	* CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
	* interface
	* ---
	*/

	#define CONFIG_MCFUART
	#define CONFIG_SYS_UART_PORT (0)

	/* ---
	* set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
	* timeout acc. to your needs
	* #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
	* for 10 sec
	* ---
	*/

	#if 0
	#define CONFIG_WATCHDOG
	#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
	#endif

	/* ---
	* CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
	* bootloader residing in flash ('chainloading'); if you want to use
	* chainloading or want to compile a u-boot binary that can be loaded into
	* RAM via BDM set
	* "#if 0" to "#if 1"
	* You will need a first stage bootloader then, e. g. colilo or a working BDM
	* cable (Background Debug Mode)
	*
	* Setting #if 0: u-boot will start from flash and relocate itself to RAM
	*
	* Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE
	* in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
	*
	* ---
	*/

	#if 0
	#define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
	#endif

	/* ---
	* Configuration for environment
	* Environment is embedded in u-boot in the second sector of the flash
	* ---
	*/

	#ifndef CONFIG_MONITOR_IS_IN_RAM
	#define CONFIG_ENV_OFFSET 0x4000
	#define CONFIG_ENV_SECT_SIZE 0x2000
	#else
	#define CONFIG_ENV_ADDR 0xffe04000
	#define CONFIG_ENV_SECT_SIZE 0x2000
	#endif

	#define LDS_BOARD_TEXT \
	. = DEFINED(env_offset) ? env_offset : .; \
	env/embedded.o(.text);

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	/*
	* Command line configuration.
	*/

	#ifdef CONFIG_MCFFEC
	# define CONFIG_MII 1
	# define CONFIG_MII_INIT 1
	# define CONFIG_SYS_DISCOVER_PHY
	# define CONFIG_SYS_RX_ETH_BUFFER 8
	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN

	# define CONFIG_SYS_FEC0_PINMUX 0
	# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
	# define MCFFEC_TOUT_LOOP 50000
	/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
	# ifndef CONFIG_SYS_DISCOVER_PHY
	# define FECDUPLEX FULL
	# define FECSPEED _100BASET
	# else
	# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	# endif
	# endif /* CONFIG_SYS_DISCOVER_PHY */
	#endif

	/*
	*-----------------------------------------------------------------------------
	* Define user parameters that have to be customized most likely
	*-----------------------------------------------------------------------------
	*/

	/AUTOBOOT settings - booting images automatically by u-boot after power on/

	/* The following settings will be contained in the environment block ; if you
	want to use a neutral environment all those settings can be manually set in
	u-boot: 'set' command */

	#if 0

	#define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please
	enter a valid image address in flash */

	/* User network settings */

	#define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
	#define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */

	#endif

	#define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address
	from which user programs will be started */

	/---/

	#define CONFIG_SYS_LONGHELP /* undef to save memory */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	/*
	*-----------------------------------------------------------------------------
	* End of user parameters to be customized
	*-----------------------------------------------------------------------------
	*/

	/* ---
	* Defines memory range for test
	* ---
	*/

	#define CONFIG_SYS_MEMTEST_START 0x400
	#define CONFIG_SYS_MEMTEST_END 0x380000

	/* ---
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	* ---
	*/

	/* ---
	* Base register address
	* ---
	*/

	#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */

	/* ---
	* System Conf. Reg. & System Protection Reg.
	* ---
	*/

	#define CONFIG_SYS_SCR 0x0003
	#define CONFIG_SYS_SPR 0xffff

	/* ---
	* Ethernet settings
	* ---
	*/

	#define CONFIG_SYS_DISCOVER_PHY
	#define CONFIG_SYS_ENET_BD_BASE 0x780000

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in internal SRAM)
	*/
	#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000

	/*
	*-------------------------------------------------------------------------
	* RAM SIZE (is defined above)
	*-----------------------------------------------------------------------
	*/

	/* #define CONFIG_SYS_SDRAM_SIZE 16 */

	/*
	*-----------------------------------------------------------------------
	*/

	#define CONFIG_SYS_FLASH_BASE 0xffe00000

	#ifdef CONFIG_MONITOR_IS_IN_RAM
	#define CONFIG_SYS_MONITOR_BASE 0x20000
	#else
	#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
	#endif

	#define CONFIG_SYS_MONITOR_LEN 0x20000
	#define CONFIG_SYS_MALLOC_LEN (256 << 10)
	#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization ??
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*-----------------------------------------------------------------------
	* FLASH organization
	*/
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CONFIG_SYS_CACHELINE_SIZE 16

	#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - 8)
	#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - 4)
	#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV \| CF_CACR_INVI)
	#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE \| \
	CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) \| \
	CF_ACR_EN \| CF_ACR_SM_ALL)
	#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB \| CF_CACR_CINV \| \
	CF_CACR_DISD \| CF_CACR_INVI \| \
	CF_CACR_CEIB \| CF_CACR_DCM \| \
	CF_CACR_EUSP)

	/*-----------------------------------------------------------------------
	* Memory bank definitions
	*
	* Please refer also to Motorola Coldfire user manual - Chapter XXX
	* <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf>
	*/
	#define CONFIG_SYS_BR0_PRELIM 0xFFE00201
	#define CONFIG_SYS_OR0_PRELIM 0xFFE00014

	#define CONFIG_SYS_BR1_PRELIM 0
	#define CONFIG_SYS_OR1_PRELIM 0

	#define CONFIG_SYS_BR2_PRELIM 0
	#define CONFIG_SYS_OR2_PRELIM 0

	#define CONFIG_SYS_BR3_PRELIM 0
	#define CONFIG_SYS_OR3_PRELIM 0

	#define CONFIG_SYS_BR4_PRELIM 0
	#define CONFIG_SYS_OR4_PRELIM 0

	#define CONFIG_SYS_BR5_PRELIM 0
	#define CONFIG_SYS_OR5_PRELIM 0

	#define CONFIG_SYS_BR6_PRELIM 0
	#define CONFIG_SYS_OR6_PRELIM 0

	#define CONFIG_SYS_BR7_PRELIM 0x00000701
	#define CONFIG_SYS_OR7_PRELIM 0xFF00007C

	/*-----------------------------------------------------------------------
	* LED config
	*/
	#define LED_STAT_0 0xffff /all LEDs off/
	#define LED_STAT_1 0xfffe
	#define LED_STAT_2 0xfffd
	#define LED_STAT_3 0xfffb
	#define LED_STAT_4 0xfff7
	#define LED_STAT_5 0xffef
	#define LED_STAT_6 0xffdf
	#define LED_STAT_7 0xff00 /all LEDs on/

	/*-----------------------------------------------------------------------
	* Port configuration (GPIO)
	*/
	#define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external
	GPIO*/
	#define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs
	(1^=output, 0^=input) */
	#define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */
	#define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART
	configuration */
	#define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */
	#define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */
	#define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */

	#endif /* _CONFIG_COBRA5272_H */