include/configs/iocon.h - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2010
  * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_405EP		1	/* this is a PPC405 CPU */
 #define CONFIG_IOCON		1	/*  on a IoCon board */

 #define	CONFIG_SYS_TEXT_BASE	0xFFFC0000

 /*
  * Include common defines/options for all AMCC eval boards
  */
 #define CONFIG_HOSTNAME		iocon
 #define CONFIG_IDENT_STRING	" iocon 0.05"
 #include "amcc-common.h"

 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_EARLY_INIT_R
 #define CONFIG_LAST_STAGE_INIT

 #define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll   */

 /*
  * Configure PLL
  */
 #define PLLMR0_DEFAULT PLLMR0_266_133_66
 #define PLLMR1_DEFAULT PLLMR1_266_133_66

 #undef CONFIG_ZERO_BOOTDELAY_CHECK	/* ignore keypress on bootdelay==0 */
 #define CONFIG_AUTOBOOT_KEYED		/* use key strings to stop autoboot */
 #define CONFIG_AUTOBOOT_STOP_STR " "

 /* new uImage format support */
 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */

 #define CONFIG_ENV_IS_IN_FLASH	/* use FLASH for environment vars */

 /*
  * Default environment variables
  */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	CONFIG_AMCC_DEF_ENV						\
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
 	"ramdisk_addr=fc200000\0"					\
 	""

 #define CONFIG_PHY_ADDR		4	/* PHY address			*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_PHY_CLK_FREQ    EMAC_STACR_CLK_66MHZ

 /*
  * Commands additional to the ones defined in amcc-common.h
  */
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_FPGAD
 #undef CONFIG_CMD_EEPROM

 /*
  * SDRAM configuration (please see cpu/ppc/sdram.[ch])
  */
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */

 /* SDRAM timings used in datasheet */
 #define CONFIG_SYS_SDRAM_CL             3	/* CAS latency */
 #define CONFIG_SYS_SDRAM_tRP           20	/* PRECHARGE command period */
 #define CONFIG_SYS_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE period */
 #define CONFIG_SYS_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
 #define CONFIG_SYS_SDRAM_tRFC          66	/* Auto refresh period */

 /*
  * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
  * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD.
  * The Linux BASE_BAUD define should match this configuration.
  *    baseBaud = cpuClock/(uartDivisor*16)
  * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
  * set Linux BASE_BAUD to 403200.
  */
 #define CONFIG_CONS_INDEX		1	/* Use UART0 */
 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK		/* external serial clock */
 #undef  CONFIG_SYS_405_UART_ERRATA_59		/* 405GP/CR Rev. D silicon */
 #define CONFIG_SYS_BASE_BAUD		691200

 /*
  * I2C stuff
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_PPC4XX
 #define CONFIG_SYS_I2C_PPC4XX_CH0
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F

 #define CONFIG_SYS_I2C_SPEED		400000

 #define CONFIG_PCA953X			/* NXP PCA9554 */
 #define CONFIG_PCA9698			/* NXP PCA9698 */

 /*
  * Software (bit-bang) I2C driver configuration
  */
 #define CONFIG_SYS_I2C_SOFT
 #define CONFIG_SYS_I2C_SOFT_SPEED		50000
 #define CONFIG_SYS_I2C_SOFT_SLAVE		0x7F
 #define I2C_SOFT_DECLARATIONS2
 #define CONFIG_SYS_I2C_SOFT_SPEED_2		50000
 #define CONFIG_SYS_I2C_SOFT_SLAVE_2		0x7F
 #define I2C_SOFT_DECLARATIONS3
 #define CONFIG_SYS_I2C_SOFT_SPEED_3		50000
 #define CONFIG_SYS_I2C_SOFT_SLAVE_3		0x7F
 #define I2C_SOFT_DECLARATIONS4
 #define CONFIG_SYS_I2C_SOFT_SPEED_4		50000
 #define CONFIG_SYS_I2C_SOFT_SLAVE_4		0x7F

 #define CONFIG_SYS_CH7301_I2C			{1, 2, 3, 4}

 #ifndef __ASSEMBLY__
 void fpga_gpio_set(unsigned int bus, int pin);
 void fpga_gpio_clear(unsigned int bus, int pin);
 int fpga_gpio_get(unsigned int bus, int pin);
 #endif

 #define I2C_ACTIVE	{ }
 #define I2C_TRISTATE	{ }
 #define I2C_READ \
 	(fpga_gpio_get(I2C_ADAP_HWNR, 0x0040) ? 1 : 0)
 #define I2C_SDA(bit) \
 	do { \
 		if (bit) \
 			fpga_gpio_set(I2C_ADAP_HWNR, 0x0040); \
 		else \
 			fpga_gpio_clear(I2C_ADAP_HWNR, 0x0040); \
 	} while (0)
 #define I2C_SCL(bit) \
 	do { \
 		if (bit) \
 			fpga_gpio_set(I2C_ADAP_HWNR, 0x0020); \
 		else \
 			fpga_gpio_clear(I2C_ADAP_HWNR, 0x0020); \
 	} while (0)
 #define I2C_DELAY	udelay(25)	/* 1/4 I2C clock duration */

 /*
  * OSD hardware
  */
 #define CONFIG_SYS_MPC92469AC
 #define CONFIG_SYS_CH7301

 /*
  * FLASH organization
  */
 #define CONFIG_SYS_FLASH_CFI		/* The flash is CFI compatible	*/
 #define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/

 #define CONFIG_SYS_FLASH_BASE		0xFC000000
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sectors per chip*/

 #define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase/ms */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write/ms */

 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buff'd writes */

 #define CONFIG_SYS_FLASH_EMPTY_INFO	/* 'E' for empty sector on flinfo */
 #define CONFIG_SYS_FLASH_QUIET_TEST	1	/* no warn upon unknown flash */

 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector */
 #define CONFIG_ENV_ADDR		((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
 #define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector */

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 #endif

 /*
  * PPC405 GPIO Configuration
  */
 #define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO	Alternate1	*/ \
 { \
 /* GPIO Core 0 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0	PerBLast */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO1	TS1E */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO2	TS2E */ \
 { GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO3	TS1O */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO4	TS2O */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_1      }, /* GPIO5	TS3 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO6	TS4 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO7	TS5 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO8	TS6 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO9	TrcClk */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10	PerCS1 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11	PerCS2 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12	PerCS3 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13	PerCS4 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14	PerAddr03 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15	PerAddr04 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16	PerAddr05 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17	IRQ0 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18	IRQ1 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19	IRQ2 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO20	IRQ3 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO21	IRQ4 */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO22	IRQ5 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO23	IRQ6 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24	UART0_DCD */ \
 { GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25	UART0_DSR */ \
 { GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26	UART0_RI */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27	UART0_DTR */ \
 { GPIO_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28	UART1_Rx */ \
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29	UART1_Tx */ \
 { GPIO_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO30	RejectPkt0 */ \
 { GPIO_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_NO_CHG }, /* GPIO31	RejectPkt1 */ \
 } \
 }

 /*
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory (OCM) for temperary stack until sdram is tested */
 #define CONFIG_SYS_TEMP_STACK_OCM        1

 /* On Chip Memory location */
 #define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
 #define CONFIG_SYS_OCM_DATA_SIZE	0x1000
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */
 #define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area */

 #define CONFIG_SYS_GBL_DATA_OFFSET \
 	(CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /*
  * External Bus Controller (EBC) Setup
  */

 /* Memory Bank 0 (NOR-FLASH) initialization */
 #define CONFIG_SYS_EBC_PB0AP		0xa382a880
 #define CONFIG_SYS_EBC_PB0CR		0xFC0DA000

 /* Memory Bank 1 (NVRAM) initializatio */
 #define CONFIG_SYS_EBC_PB1AP		0x92015480
 #define CONFIG_SYS_EBC_PB1CR		0xFB858000

 /* Memory Bank 2 (FPGA0) initialization */
 #define CONFIG_SYS_FPGA0_BASE		0x7f100000
 #define CONFIG_SYS_EBC_PB2AP		0x02825080
 #define CONFIG_SYS_EBC_PB2CR		(CONFIG_SYS_FPGA0_BASE | 0x1a000)

 #define CONFIG_SYS_FPGA_BASE(k)		CONFIG_SYS_FPGA0_BASE
 #define CONFIG_SYS_FPGA_DONE(k)		0x0010

 #define CONFIG_SYS_FPGA_COUNT		1

 #define CONFIG_SYS_MCLINK_MAX		3

 #define CONFIG_SYS_FPGA_PTR \
 	{ (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }

 /* Memory Bank 3 (Latches) initialization */
 #define CONFIG_SYS_LATCH_BASE		0x7f200000
 #define CONFIG_SYS_EBC_PB3AP		0x02025080
 #define CONFIG_SYS_EBC_PB3CR		0x7f21a000

 #define CONFIG_SYS_LATCH0_RESET		0xffef
 #define CONFIG_SYS_LATCH0_BOOT		0xffff
 #define CONFIG_SYS_LATCH1_RESET		0xffff
 #define CONFIG_SYS_LATCH1_BOOT		0xffff

 /*
  * OSD Setup
  */
 #define CONFIG_SYS_MPC92469AC
 #define CONFIG_SYS_CH7301
 #define CONFIG_SYS_OSD_SCREENS		1

 #define CONFIG_BITBANGMII		/* bit-bang MII PHY management */
 #define CONFIG_BITBANGMII_MULTI

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2010
	* Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_405EP 1 /* this is a PPC405 CPU */
	#define CONFIG_IOCON 1 /* on a IoCon board */

	#define CONFIG_SYS_TEXT_BASE 0xFFFC0000

	/*
	* Include common defines/options for all AMCC eval boards
	*/
	#define CONFIG_HOSTNAME iocon
	#define CONFIG_IDENT_STRING " iocon 0.05"
	#include "amcc-common.h"

	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_EARLY_INIT_R
	#define CONFIG_LAST_STAGE_INIT

	#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */

	/*
	* Configure PLL
	*/
	#define PLLMR0_DEFAULT PLLMR0_266_133_66
	#define PLLMR1_DEFAULT PLLMR1_266_133_66

	#undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */
	#define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */
	#define CONFIG_AUTOBOOT_STOP_STR " "

	/* new uImage format support */
	#define CONFIG_FIT
	#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */

	#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */

	/*
	* Default environment variables
	*/
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_AMCC_DEF_ENV \
	CONFIG_AMCC_DEF_ENV_POWERPC \
	CONFIG_AMCC_DEF_ENV_NOR_UPD \
	"kernel_addr=fc000000\0" \
	"fdt_addr=fc1e0000\0" \
	"ramdisk_addr=fc200000\0" \
	""

	#define CONFIG_PHY_ADDR 4 /* PHY address */
	#define CONFIG_HAS_ETH0
	#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ

	/*
	* Commands additional to the ones defined in amcc-common.h
	*/
	#define CONFIG_CMD_CACHE
	#define CONFIG_CMD_FPGAD
	#undef CONFIG_CMD_EEPROM

	/*
	* SDRAM configuration (please see cpu/ppc/sdram.[ch])
	*/
	#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */

	/* SDRAM timings used in datasheet */
	#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */
	#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */
	#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE period */
	#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
	#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */

	/*
	* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
	* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
	* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD.
	* The Linux BASE_BAUD define should match this configuration.
	* baseBaud = cpuClock/(uartDivisor*16)
	* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
	* set Linux BASE_BAUD to 403200.
	*/
	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
	#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
	#define CONFIG_SYS_BASE_BAUD 691200

	/*
	* I2C stuff
	*/
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_PPC4XX
	#define CONFIG_SYS_I2C_PPC4XX_CH0
	#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
	#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F

	#define CONFIG_SYS_I2C_SPEED 400000

	#define CONFIG_PCA953X /* NXP PCA9554 */
	#define CONFIG_PCA9698 /* NXP PCA9698 */

	/*
	* Software (bit-bang) I2C driver configuration
	*/
	#define CONFIG_SYS_I2C_SOFT
	#define CONFIG_SYS_I2C_SOFT_SPEED 50000
	#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
	#define I2C_SOFT_DECLARATIONS2
	#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
	#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
	#define I2C_SOFT_DECLARATIONS3
	#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
	#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F
	#define I2C_SOFT_DECLARATIONS4
	#define CONFIG_SYS_I2C_SOFT_SPEED_4 50000
	#define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F

	#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4}

	#ifndef __ASSEMBLY__
	void fpga_gpio_set(unsigned int bus, int pin);
	void fpga_gpio_clear(unsigned int bus, int pin);
	int fpga_gpio_get(unsigned int bus, int pin);
	#endif

	#define I2C_ACTIVE { }
	#define I2C_TRISTATE { }
	#define I2C_READ \
	(fpga_gpio_get(I2C_ADAP_HWNR, 0x0040) ? 1 : 0)
	#define I2C_SDA(bit) \
	do { \
	if (bit) \
	fpga_gpio_set(I2C_ADAP_HWNR, 0x0040); \
	else \
	fpga_gpio_clear(I2C_ADAP_HWNR, 0x0040); \
	} while (0)
	#define I2C_SCL(bit) \
	do { \
	if (bit) \
	fpga_gpio_set(I2C_ADAP_HWNR, 0x0020); \
	else \
	fpga_gpio_clear(I2C_ADAP_HWNR, 0x0020); \
	} while (0)
	#define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */

	/*
	* OSD hardware
	*/
	#define CONFIG_SYS_MPC92469AC
	#define CONFIG_SYS_CH7301

	/*
	* FLASH organization
	*/
	#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
	#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */

	#define CONFIG_SYS_FLASH_BASE 0xFC000000
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors per chip*/

	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms */

	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buff'd writes */

	#define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */
	#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* no warn upon unknown flash */

	#ifdef CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
	#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
	#endif

	/*
	* PPC405 GPIO Configuration
	*/
	#define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \
	{ \
	/* GPIO Core 0 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \
	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO5 TS3 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO6 TS4 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO7 TS5 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO9 TrcClk */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \
	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \
	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \
	{ GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \
	{ GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \
	{ GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \
	} \
	}

	/*
	* Definitions for initial stack pointer and data area (in data cache)
	*/
	/* use on chip memory (OCM) for temperary stack until sdram is tested */
	#define CONFIG_SYS_TEMP_STACK_OCM 1

	/* On Chip Memory location */
	#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
	#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */
	#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area */

	#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/*
	* External Bus Controller (EBC) Setup
	*/

	/* Memory Bank 0 (NOR-FLASH) initialization */
	#define CONFIG_SYS_EBC_PB0AP 0xa382a880
	#define CONFIG_SYS_EBC_PB0CR 0xFC0DA000

	/* Memory Bank 1 (NVRAM) initializatio */
	#define CONFIG_SYS_EBC_PB1AP 0x92015480
	#define CONFIG_SYS_EBC_PB1CR 0xFB858000

	/* Memory Bank 2 (FPGA0) initialization */
	#define CONFIG_SYS_FPGA0_BASE 0x7f100000
	#define CONFIG_SYS_EBC_PB2AP 0x02825080
	#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA0_BASE \| 0x1a000)

	#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE
	#define CONFIG_SYS_FPGA_DONE(k) 0x0010

	#define CONFIG_SYS_FPGA_COUNT 1

	#define CONFIG_SYS_MCLINK_MAX 3

	#define CONFIG_SYS_FPGA_PTR \
	{ (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }

	/* Memory Bank 3 (Latches) initialization */
	#define CONFIG_SYS_LATCH_BASE 0x7f200000
	#define CONFIG_SYS_EBC_PB3AP 0x02025080
	#define CONFIG_SYS_EBC_PB3CR 0x7f21a000

	#define CONFIG_SYS_LATCH0_RESET 0xffef
	#define CONFIG_SYS_LATCH0_BOOT 0xffff
	#define CONFIG_SYS_LATCH1_RESET 0xffff
	#define CONFIG_SYS_LATCH1_BOOT 0xffff

	/*
	* OSD Setup
	*/
	#define CONFIG_SYS_MPC92469AC
	#define CONFIG_SYS_CH7301
	#define CONFIG_SYS_OSD_SCREENS 1

	#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
	#define CONFIG_BITBANGMII_MULTI

	#endif /* __CONFIG_H */