| /* |
| * U-boot - Configuration file for BF533 STAMP board |
| */ |
| |
| #ifndef __CONFIG_BF533_STAMP_H__ |
| #define __CONFIG_BF533_STAMP_H__ |
| |
| #include <asm/config-pre.h> |
| |
| |
| /* |
| * Processor Settings |
| */ |
| #define CONFIG_BFIN_CPU bf533-0.3 |
| #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS |
| |
| /* |
| * Clock Settings |
| * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV |
| * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV |
| */ |
| /* CONFIG_CLKIN_HZ is any value in Hz */ |
| #define CONFIG_CLKIN_HZ 11059200 |
| /* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ |
| /* 1 = CLKIN / 2 */ |
| #define CONFIG_CLKIN_HALF 0 |
| /* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ |
| /* 1 = bypass PLL */ |
| #define CONFIG_PLL_BYPASS 0 |
| /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ |
| /* Values can range from 0-63 (where 0 means 64) */ |
| #define CONFIG_VCO_MULT 45 |
| /* CCLK_DIV controls the core clock divider */ |
| /* Values can be 1, 2, 4, or 8 ONLY */ |
| #define CONFIG_CCLK_DIV 1 |
| /* SCLK_DIV controls the system clock divider */ |
| /* Values can range from 1-15 */ |
| #define CONFIG_SCLK_DIV 6 /* note: 1.2 boards can go faster */ |
| |
| /* |
| * Memory Settings |
| */ |
| #define CONFIG_MEM_ADD_WDTH 11 |
| #define CONFIG_MEM_SIZE 128 |
| |
| #define CONFIG_EBIU_SDRRC_VAL 0x268 |
| #define CONFIG_EBIU_SDGCTL_VAL 0x911109 |
| |
| #define CONFIG_EBIU_AMGCTL_VAL 0xFF |
| #define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 |
| #define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (384 * 1024) |
| |
| |
| /* |
| * Network Settings |
| */ |
| #define ADI_CMDS_NETWORK 1 |
| #define CONFIG_SMC91111 1 |
| #define CONFIG_SMC91111_BASE 0x20300300 |
| #define SMC91111_EEPROM_INIT() \ |
| do { \ |
| bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \ |
| bfin_write_FIO_FLAG_C(PF1); \ |
| bfin_write_FIO_FLAG_S(PF0); \ |
| SSYNC(); \ |
| } while (0) |
| #define CONFIG_HOSTNAME bf533-stamp |
| /* Uncomment next line to use fixed MAC address */ |
| /* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ |
| |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ |
| #define CONFIG_SYS_I2C_SOFT_SPEED 50000 |
| #define CONFIG_SYS_I2C_SOFT_SLAVE 0 |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3 |
| #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2 |
| |
| /* |
| * Flash Settings |
| */ |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_BASE 0x20000000 |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_CFI_AMD_RESET |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #define CONFIG_SYS_MAX_FLASH_SECT 67 |
| |
| /* |
| * SPI Settings |
| */ |
| #define CONFIG_BFIN_SPI |
| #define CONFIG_ENV_SPI_MAX_HZ 30000000 |
| #define CONFIG_SF_DEFAULT_SPEED 30000000 |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_SPI_FLASH_ALL |
| |
| |
| /* |
| * Env Storage Settings |
| */ |
| #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_OFFSET 0x10000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_OFFSET 0x4000 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x2000 |
| #endif |
| #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) |
| #define ENV_IS_EMBEDDED |
| #else |
| #define CONFIG_ENV_IS_EMBEDDED_IN_LDR |
| #endif |
| #ifdef ENV_IS_EMBEDDED |
| /* WARNING - the following is hand-optimized to fit within |
| * the sector before the environment sector. If it throws |
| * an error during compilation remove an object here to get |
| * it linked after the configuration sector. |
| */ |
| # define LDS_BOARD_TEXT \ |
| arch/blackfin/lib/built-in.o (.text*); \ |
| arch/blackfin/cpu/built-in.o (.text*); \ |
| . = DEFINED(env_offset) ? env_offset : .; \ |
| common/env_embedded.o (.text*); |
| #endif |
| |
| |
| /* |
| * I2C Settings |
| */ |
| #define CONFIG_SYS_I2C_SOFT |
| #ifdef CONFIG_SYS_I2C_SOFT |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3 |
| #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2 |
| #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ |
| #define CONFIG_SYS_I2C_SOFT_SPEED 50000 |
| #define CONFIG_SYS_I2C_SOFT_SLAVE 0 |
| #endif |
| |
| /* |
| * Compact Flash / IDE / ATA Settings |
| */ |
| |
| /* Enabled below option for CF support */ |
| /* #define CONFIG_STAMP_CF */ |
| #if defined(CONFIG_STAMP_CF) |
| #define CONFIG_MISC_INIT_R |
| #define CONFIG_DOS_PARTITION 1 |
| #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ |
| #undef CONFIG_IDE_LED /* no led for ide supported */ |
| #undef CONFIG_IDE_RESET /* no reset for ide supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 |
| #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR 0x20200000 |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */ |
| |
| #define CONFIG_SYS_ATA_STRIDE 2 |
| |
| #undef CONFIG_EBIU_AMBCTL1_VAL |
| #define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 |
| #endif |
| |
| |
| /* |
| * Misc Settings |
| */ |
| #define CONFIG_RTC_BFIN |
| #define CONFIG_UART_CONSOLE 0 |
| #define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED |
| |
| /* FLASH/ETHERNET uses the same async bank */ |
| #define SHARED_RESOURCES 1 |
| |
| /* define to enable boot progress via leds */ |
| /* #define CONFIG_SHOW_BOOT_PROGRESS */ |
| |
| /* define to enable run status via led */ |
| /* #define CONFIG_STATUS_LED */ |
| #ifdef CONFIG_STATUS_LED |
| #define CONFIG_GPIO_LED |
| #define CONFIG_BOARD_SPECIFIC_LED |
| /* use LED0 to indicate booting/alive */ |
| #define STATUS_LED_BOOT 0 |
| #define STATUS_LED_BIT GPIO_PF2 |
| #define STATUS_LED_STATE STATUS_LED_ON |
| #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4) |
| /* use LED1 to indicate crash */ |
| #define STATUS_LED_CRASH 1 |
| #define STATUS_LED_BIT1 GPIO_PF3 |
| #define STATUS_LED_STATE1 STATUS_LED_ON |
| #define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) |
| /* #define STATUS_LED_BIT2 GPIO_PF4 */ |
| #endif |
| |
| /* define to enable splash screen support */ |
| /* #define CONFIG_VIDEO */ |
| |
| |
| /* |
| * Pull in common ADI header for remaining command/environment setup |
| */ |
| #include <configs/bfin_adi_common.h> |
| |
| #endif |