| /* |
| * (C) Copyright 2004 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| /* Yoo. Jonghoon, IPone, yooth@ipone.co.kr |
| * U-BOOT port on RPXlite board |
| */ |
| |
| /* |
| * Sam Song, IEMC. SHU, samsongshu@yahoo.com.cn |
| * U-BOOT port on RPXlite DW version board--RPXlite_DW |
| * June 8 ,2004 |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| /* #define DEBUG 1 */ |
| /* #define DEPLOYMENT 1 */ |
| |
| #undef CONFIG_MPC860 |
| #define CONFIG_MPC823 1 /* This is a MPC823e CPU. */ |
| #define CONFIG_RPXLITE 1 /* RPXlite DW version board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xff000000 |
| |
| #ifdef CONFIG_LCD /* with LCD controller ? */ |
| #define CONFIG_MPC8XX_LCD |
| #define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ |
| #endif |
| |
| #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
| #undef CONFIG_8xx_CONS_SMC2 |
| #undef CONFIG_8xx_CONS_NONE |
| #define CONFIG_BAUDRATE 9600 /* console default baudrate = 9600bps */ |
| |
| #ifdef DEBUG |
| #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ |
| #else |
| #define CONFIG_BOOTDELAY 6 /* autoboot after 6 seconds */ |
| |
| #ifdef DEPLOYMENT |
| #define CONFIG_BOOT_RETRY_TIME -1 |
| #define CONFIG_AUTOBOOT_KEYED |
| #define CONFIG_AUTOBOOT_PROMPT \ |
| "autoboot in %d seconds (stop with 'st')...\n", bootdelay |
| #define CONFIG_AUTOBOOT_STOP_STR "st" |
| #define CONFIG_ZERO_BOOTDELAY_CHECK |
| #define CONFIG_RESET_TO_RETRY 1 |
| #define CONFIG_BOOT_RETRY_MIN 1 |
| #endif /* DEPLOYMENT */ |
| #endif /* DEBUG */ |
| |
| /* pre-boot commands */ |
| #define CONFIG_PREBOOT "setenv stdout serial;setenv stdin serial" |
| |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "nfsargs=setenv bootargs console=tty0 console=ttyS0,9600 " \ |
| "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs console=tty0 root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "flash_nfs=run nfsargs addip;" \ |
| "bootm ${kernel_addr}\0" \ |
| "flash_self=run ramargs addip;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ |
| "gatewayip=172.16.115.254\0" \ |
| "netmask=255.255.255.0\0" \ |
| "kernel_addr=ff040000\0" \ |
| "ramdisk_addr=ff200000\0" \ |
| "ku=era ${kernel_addr} ff1fffff;cp.b 100000 ${kernel_addr} " \ |
| "${filesize};md ${kernel_addr};" \ |
| "echo kernel updating finished\0" \ |
| "uu=protect off 1:0-4;era 1:0-4;cp.b 100000 ff000000 " \ |
| "${filesize};md ff000000;" \ |
| "echo u-boot updating finished\0" \ |
| "eu=protect off 1:6;era 1:6;reset\0" \ |
| "lcd=setenv stdout lcd;setenv stdin lcd\0" \ |
| "ser=setenv stdout serial;setenv stdin serial\0" \ |
| "verify=no" |
| |
| #define CONFIG_BOOTCOMMAND "run flash_self" |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| #undef CONFIG_STATUS_LED /* disturbs display. Status LED disabled. */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| |
| #if 1 /* Enable this stuff could make image enlarge about 25KB. Mask it if you |
| don't want the advanced function */ |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_DHCP |
| |
| #ifdef CONFIG_SPLASH_SCREEN |
| #define CONFIG_CMD_BMP |
| #endif |
| |
| |
| /* test-only */ |
| #define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ |
| #define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ |
| |
| #define CONFIG_NETCONSOLE |
| |
| #endif /* 1 */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "u-boot>" /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */ |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| /*----------------------------------------------------------------------- |
| * Internal Memory Mapped Register |
| */ |
| #define CONFIG_SYS_IMMR 0xFA200000 |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0xFF000000 |
| |
| #if defined(DEBUG) || defined(CONFIG_CMD_IDE) |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #else |
| #define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_BASE 0xFF000000 |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #ifdef CONFIG_ENV_IS_IN_NVRAM |
| #define CONFIG_ENV_ADDR 0xFA000100 |
| #define CONFIG_ENV_SIZE 0x1000 |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_OFFSET 0x30000 /* Offset of Environment Sector */ |
| #define CONFIG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */ |
| #endif /* CONFIG_ENV_IS_IN_NVRAM */ |
| |
| #define CONFIG_SYS_RESET_ADDRESS ((ulong)((((immap_t *)CONFIG_SYS_IMMR)->im_clkrst.res))) |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control 32-bit 12-35 |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze |
| */ |
| #if defined(CONFIG_WATCHDOG) |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
| #else |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) |
| #endif /* We can get SYPCR: 0xFFFF0689. */ |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration 32-bit 12-30 |
| *----------------------------------------------------------------------- |
| * PCMCIA config., multi-function pin tri-state |
| */ |
| #define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10) /* SIUMCR:0x00000800 */ |
| |
| /*--------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control 16-bit 12-16 |
| *--------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| */ |
| #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE) |
| /* TBSCR: 0x00C3 [SAM] */ |
| |
| /*----------------------------------------------------------------------- |
| * RTCSC - Real-Time Clock Status and Control Register 16-bit 12-18 |
| *----------------------------------------------------------------------- |
| * [RTC enabled but not stopped on FRZ] |
| */ |
| #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTE) /* RTCSC:0x00C1 */ |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control 16-bit 12-23 |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| * [Periodic timer enabled,Periodic timer interrupt disable. ] |
| */ |
| #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /* PISCR:0x0083 */ |
| |
| /*----------------------------------------------------------------------- |
| * PLPRCR - PLL, Low-Power, and Reset Control Register 32-bit 5-7 |
| *----------------------------------------------------------------------- |
| * Reset PLL lock status sticky bit, timer expired status bit and timer |
| * interrupt status bit |
| */ |
| /* up to 64 MHz we use a 1:2 clock */ |
| #if defined(RPXlite_64MHz) |
| #define CONFIG_SYS_PLPRCR ( (7 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) /*PLPRCR: 0x00700000. */ |
| #else |
| #define CONFIG_SYS_PLPRCR ( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS ) |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register 5-3 |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #define SCCR_MASK SCCR_EBDF00 |
| /* Up to 48MHz system clock, we use 1:1 SYSTEM/BUS ratio */ |
| #if defined(RPXlite_64MHz) |
| #define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF01 ) /* %%%SCCR:0x02020000 */ |
| #else |
| #define CONFIG_SYS_SCCR ( SCCR_TBS | SCCR_EBDF00 ) /* %%%SCCR:0x02000000 */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * PCMCIA stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) |
| #define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) |
| #define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) |
| #define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) |
| #define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ |
| #define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| #undef CONFIG_IDE_RESET /* reset for ide not supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| #define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR |
| |
| /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) |
| |
| /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) |
| |
| /* Offset for alternate registers */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 |
| |
| #define CONFIG_SYS_DER 0 |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0 and OR0 (FLASH) |
| */ |
| #define FLASH_BASE_PRELIM 0xFC000000 /* FLASH base */ |
| #define CONFIG_SYS_PRELIM_OR_AM 0xFC000000 /* OR addr mask */ |
| |
| /* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 8, ETHR = 0, BIH = 1 */ |
| #define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_BI) |
| #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) |
| #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V) |
| |
| /* |
| * BR1 and OR1 (SDRAM) |
| * |
| */ |
| #define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */ |
| #define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB in system */ |
| |
| /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ |
| #define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00 |
| #define CONFIG_SYS_OR_AM_SDRAM (-(SDRAM_MAX_SIZE & OR_AM_MSK)) |
| #define CONFIG_SYS_OR1_PRELIM ( CONFIG_SYS_OR_AM_SDRAM | CONFIG_SYS_OR_TIMING_SDRAM ) |
| #define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) |
| |
| /* RPXlite mem setting */ |
| #define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */ |
| #define CONFIG_SYS_OR3_PRELIM 0xFF7F8900 |
| #define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */ |
| #define CONFIG_SYS_OR4_PRELIM 0xFFFE0040 |
| |
| /* |
| * Memory Periodic Timer Prescaler |
| */ |
| /* periodic timer for refresh */ |
| #if defined(RPXlite_64MHz) |
| #define CONFIG_SYS_MAMR_PTA 32 |
| #else |
| #define CONFIG_SYS_MAMR_PTA 20 |
| #endif |
| |
| /* |
| * Refresh clock Prescalar |
| */ |
| #define CONFIG_SYS_MPTPR MPTPR_PTP_DIV2 |
| |
| /* |
| * MAMR settings for SDRAM |
| */ |
| |
| /* 9 column SDRAM */ |
| #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10) |
| /* CONFIG_SYS_MAMR_9COL:0x20904000 @ 64MHz */ |
| |
| /*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ |
| /* Configuration variable added by yooth. */ |
| /*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */ |
| /* |
| * BCSRx |
| * |
| * Board Status and Control Registers |
| * |
| */ |
| #define BCSR0 0xFA400000 |
| #define BCSR1 0xFA400001 |
| #define BCSR2 0xFA400002 |
| #define BCSR3 0xFA400003 |
| |
| #define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */ |
| #define BCSR0_ENNVRAM 0x02 /* CS4# Control */ |
| #define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */ |
| #define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */ |
| #define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */ |
| #define BCSR0_COLTEST 0x20 |
| #define BCSR0_ETHLPBK 0x40 |
| #define BCSR0_ETHEN 0x80 |
| |
| #define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */ |
| #define BCSR1_PCVCTL6 0x02 |
| #define BCSR1_PCVCTL5 0x04 |
| #define BCSR1_PCVCTL4 0x08 |
| #define BCSR1_IPB5SEL 0x10 |
| |
| #define BCSR1_SMC1CTS 0x40 /* Added by SAM. */ |
| #define BCSR1_SMC1TRS 0x80 /* Added by SAM. */ |
| |
| #define BCSR2_ENRTCIRQ 0x01 /* Added by SAM. */ |
| #define BCSR2_ENBRG1 0x04 /* Added by SAM. */ |
| |
| #define BCSR2_ENPA5HDR 0x08 /* USB Control */ |
| #define BCSR2_ENUSBCLK 0x10 |
| #define BCSR2_USBPWREN 0x20 |
| #define BCSR2_USBSPD 0x40 |
| #define BCSR2_USBSUSP 0x80 |
| |
| #define BCSR3_BWKAPWR 0x01 /* Changed by SAM. Backup battery situation */ |
| #define BCSR3_IRQRTC 0x02 /* Changed by SAM. NVRAM Battery */ |
| #define BCSR3_RDY_BSY 0x04 /* Changed by SAM. Flash Operation */ |
| #define BCSR3_MPLX_LIN 0x08 /* Changed by SAM. Linear or Multiplexed address Mode */ |
| |
| #define BCSR3_D27 0x10 /* Dip Switch settings */ |
| #define BCSR3_D26 0x20 |
| #define BCSR3_D25 0x40 |
| #define BCSR3_D24 0x80 |
| |
| /* |
| * Environment setting |
| */ |
| #define CONFIG_ETHADDR 00:10:EC:00:37:5B |
| #define CONFIG_IPADDR 172.16.115.7 |
| #define CONFIG_SERVERIP 172.16.115.6 |
| #define CONFIG_ROOTPATH "/workspace/myfilesystem/target/" |
| #define CONFIG_BOOTFILE "uImage.rpxusb" |
| #define CONFIG_HOSTNAME LITE_H1_DW |
| |
| #endif /* __CONFIG_H */ |