blob: 2bdc55b4673f974ee9ba835213462a0bb4acabc1 [file] [log] [blame]
/*
* (C) Copyright 2000-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC860 1
#define CONFIG_MPC860T 1
#define CONFIG_MPC862 1 /* enable 862 since the */
#define CONFIG_MPC857 1 /* 857 is a variant of the 862 */
#define CONFIG_UC100 1 /* ...on a UC100 module */
#define MPC8XX_FACT 4 /* Multiply by 4 */
#define MPC8XX_XIN 25000000 /* 25.0 MHz in */
#define CONFIG_8xx_GCLK_FREQ (MPC8XX_FACT * MPC8XX_XIN)
/* define if cant' use get_gclk_freq */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_BOARD_TYPES 1 /* support board types */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_8xx\0" \
"bootfile=/tftpboot/uc100/uImage\0" \
"kernel_addr=40000000\0" \
"ramdisk_addr=40100000\0" \
"load=tftp 100000 /tftpboot/uc100/u-boot.bin\0" \
"update=protect off 40700000 4073ffff;era 40700000 4073ffff;" \
"cp.b 100000 40700000 ${filesize};" \
"setenv filesize;saveenv\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#undef CONFIG_STATUS_LED /* no status-led */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#undef CONFIG_RTC_MPC8xx
#define CFG_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */
#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */
/*
* Power On Self Test support
*/
#define CONFIG_POST ( CFG_POST_CACHE | \
CFG_POST_MEMORY | \
CFG_POST_CPU | \
CFG_POST_UART | \
CFG_POST_SPR )
#undef CONFIG_POST
#ifdef CONFIG_POST
#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
#else
#define CFG_CMD_POST_DIAG 0
#endif
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#define CONFIG_CMD_MII
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_POST
#define CONFIG_CMD_SNTP
#define CONFIG_NETCONSOLE
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if 0
#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
#endif
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CFG_IMMR 0xF0000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x40000000
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MONITOR_BASE (CFG_FLASH_BASE+0x00700000) /* resetvec fff00100*/
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*-----------------------------------------------------------------------
* Address accessed to reset the board - must not be mapped/assigned
*/
#define CFG_RESET_ADDRESS 0x90000000
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_FLASH_CFI /* The flash is CFI compatible */
#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE+CFG_MONITOR_LEN)
#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR+CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
#define CFG_SIUMCR (SIUMCR_FRC | SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
*/
#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK 0x00000000
#define CFG_SCCR (SCCR_EBDF11)
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
#define CFG_PCMCIA_IO_ADDR (0xEC000000)
#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
*-----------------------------------------------------------------------
*/
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
/* Offset for data I/O */
#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET 0x0100
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
#define CFG_DER 0
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
/* used to re-map FLASH both when starting from SRAM or FLASH:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
/*
* FLASH timing:
*/
#define CFG_OR_TIMING_FLASH (0x00000d24)
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
#define CFG_BR1_PRELIM 0x00000081 /* Chip select for SDRAM (32 Bit, UPMA) */
#define CFG_OR1_PRELIM 0xfc000a00
#define CFG_BR2_PRELIM 0x80000001 /* Chip select for SRAM (32 Bit, GPCM) */
#define CFG_OR2_PRELIM 0xfff00d24
#define CFG_BR3_PRELIM 0x80600401 /* Chip select for Display (8 Bit, GPCM) */
#define CFG_OR3_PRELIM 0xffff8f44
#define CFG_BR4_PRELIM 0xc05108c1 /* Chip select for Interbus MPM (16 Bit, UPMB) */
#define CFG_OR4_PRELIM 0xffff0300
#define CFG_BR5_PRELIM 0xc0500401 /* Chip select for Interbus Status (8 Bit, GPCM) */
#define CFG_OR5_PRELIM 0xffff8db0
/*
* Memory Periodic Timer Prescaler
*
* The Divider for PTA (refresh timer) configuration is based on an
* example SDRAM configuration (64 MBit, one bank). The adjustment to
* the number of chip selects (NCS) and the actually needed refresh
* rate is done by setting MPTPR.
*
* PTA is calculated from
* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
*
* gclk CPU clock (not bus clock!)
* Trefresh Refresh cycle * 4 (four word bursts used)
*
* 4096 Rows from SDRAM example configuration
* 1000 factor s -> ms
* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
* 4 Number of refresh cycles per period
* 64 Refresh cycle in ms per number of rows
* --------------------------------------------
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
*
* 50 MHz => 50.000.000 / Divider = 98
* 66 Mhz => 66.000.000 / Divider = 129
* 80 Mhz => 80.000.000 / Divider = 156
* 100 Mhz => 100.000.000 / Divider = 195
*/
#define CFG_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
#define CFG_MAMR_PTA 98
/*
* For 16 MBit, refresh rates could be 31.3 us
* (= 64 ms / 2K = 125 / quad bursts).
* For a simpler initialization, 15.6 us is used instead.
*
* #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
* #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
*/
#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
/* 8 column SDRAM */
#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
#define CFG_MAMR_VAL 0x30904114 /* for SDRAM */
#define CFG_MBMR_VAL 0xff001111 /* for Interbus-MPM */
/*-----------------------------------------------------------------------
* I2C stuff
*/
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */
#define CFG_I2C_SLAVE 0xFE
#ifdef CONFIG_SOFT_I2C
/*
* Software (bit-bang) I2C driver configuration
*/
#define PB_SCL 0x00000020 /* PB 26 */
#define PB_SDA 0x00000010 /* PB 27 */
#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
else immr->im_cpm.cp_pbdat &= ~PB_SDA
#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
else immr->im_cpm.cp_pbdat &= ~PB_SCL
#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
#endif /* CONFIG_SOFT_I2C */
/*-----------------------------------------------------------------------
* I2C EEPROM (24C164)
*/
#define CFG_I2C_EEPROM_ADDR 0x58 /* EEPROM AT24C164 */
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_BITS 4
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
#define FEC_ENET
#define CONFIG_MII
#define CFG_DISCOVER_PHY 1
#endif /* __CONFIG_H */