| /* |
| * (C) Copyright 2003-2004 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * (C) Copyright 2004 |
| * Mark Jonas, Freescale Semiconductor, mark.jonas@freescale.com. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * Check valid setting of revision define. |
| * Total5100 and Total5200 Rev.1 are identical except for the processor. |
| */ |
| #if (CONFIG_TOTAL5200_REV!=1 && CONFIG_TOTAL5200_REV!=2) |
| #error CONFIG_TOTAL5200_REV must be 1 or 2 |
| #endif |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ |
| #define CONFIG_TOTAL5200 1 /* ... on Total5200 board */ |
| |
| /* |
| * Valid values for CONFIG_SYS_TEXT_BASE are: |
| * 0xFFF00000 boot high (standard configuration) |
| * 0xFE000000 boot low |
| * 0x00100000 boot from RAM (for testing only) |
| */ |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFFF00000 |
| #endif |
| |
| #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* |
| * Serial console configuration |
| */ |
| #define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ |
| #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| |
| /* |
| * Video console |
| */ |
| #define CONFIG_VIDEO |
| #define CONFIG_VIDEO_SED13806 |
| #define CONFIG_VIDEO_SED13806_16BPP |
| |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VIDEO_LOGO |
| /* #define CONFIG_VIDEO_BMP_LOGO */ |
| #define CONFIG_CONSOLE_EXTRA_INFO |
| #define CONFIG_VGA_AS_SINGLE_DEVICE |
| #define CONFIG_VIDEO_SW_CURSOR |
| #define CONFIG_SPLASH_SCREEN |
| |
| |
| /* |
| * PCI Mapping: |
| * 0x40000000 - 0x4fffffff - PCI Memory |
| * 0x50000000 - 0x50ffffff - PCI IO Space |
| */ |
| #define CONFIG_PCI 1 |
| #define CONFIG_PCI_PNP 1 |
| #define CONFIG_PCI_SCAN_SHOW 1 |
| #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 |
| |
| #define CONFIG_PCI_MEM_BUS 0x40000000 |
| #define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS |
| #define CONFIG_PCI_MEM_SIZE 0x10000000 |
| |
| #define CONFIG_PCI_IO_BUS 0x50000000 |
| #define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS |
| #define CONFIG_PCI_IO_SIZE 0x01000000 |
| |
| #define CONFIG_MII 1 |
| #define CONFIG_EEPRO100 1 |
| #define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ |
| #define CONFIG_NS8382X 1 |
| |
| /* Partitions */ |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| |
| /* USB */ |
| #define CONFIG_USB_OHCI |
| #define CONFIG_USB_STORAGE |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PCI |
| |
| #define CONFIG_CMD_BMP |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_USB |
| |
| |
| #if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */ |
| # define CONFIG_SYS_LOWBOOT 1 |
| #endif |
| |
| /* |
| * Autobooting |
| */ |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_PREBOOT \ |
| "setenv stdout serial;setenv stderr serial;" \ |
| "echo;" \ |
| "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ |
| "echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "flash_nfs=run nfsargs addip;" \ |
| "bootm ${kernel_addr}\0" \ |
| "flash_self=run ramargs addip;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ |
| "rootpath=/opt/eldk/ppc_82xx\0" \ |
| "bootfile=/tftpboot/MPC5200/uImage\0" \ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run flash_self" |
| |
| /* |
| * IPB Bus clocking configuration. |
| */ |
| #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ |
| |
| /* |
| * I2C configuration |
| */ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ |
| |
| #define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| |
| /* |
| * EEPROM configuration |
| */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 |
| |
| /* |
| * Flash configuration |
| */ |
| #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ |
| #if CONFIG_TOTAL5200_REV==2 |
| # define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */ |
| # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS5_START, CONFIG_SYS_CS4_START, CONFIG_SYS_BOOTCS_START } |
| #else |
| # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ |
| # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } |
| #endif |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ |
| |
| #if CONFIG_TOTAL5200_REV==1 |
| # define CONFIG_SYS_FLASH_BASE 0xFE000000 |
| # define CONFIG_SYS_FLASH_SIZE 0x02000000 |
| #elif CONFIG_TOTAL5200_REV==2 |
| # define CONFIG_SYS_FLASH_BASE 0xFA000000 |
| # define CONFIG_SYS_FLASH_SIZE 0x06000000 |
| #endif /* CONFIG_TOTAL5200_REV */ |
| |
| #if defined(CONFIG_SYS_LOWBOOT) |
| # define CONFIG_ENV_ADDR 0xFE040000 |
| #else /* CONFIG_SYS_LOWBOOT */ |
| # define CONFIG_ENV_ADDR 0xFFF40000 |
| #endif /* CONFIG_SYS_LOWBOOT */ |
| |
| /* |
| * Environment settings |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_SIZE 0x40000 |
| #define CONFIG_ENV_SECT_SIZE 0x40000 |
| #define CONFIG_ENV_OVERWRITE 1 |
| |
| /* |
| * Memory map |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_DEFAULT_MBAR 0x80000000 |
| #define CONFIG_SYS_MBAR 0xF0000000 /* 64 kB */ |
| #define CONFIG_SYS_FPGA_BASE 0xF0010000 /* 64 kB */ |
| #define CONFIG_SYS_CPLD_BASE 0xF0020000 /* 64 kB */ |
| #define CONFIG_SYS_LCD_BASE 0xF1000000 /* 4096 kB */ |
| |
| /* Use SRAM until RAM will be available */ |
| #define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM |
| #define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| # define CONFIG_SYS_RAMBOOT 1 |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Ethernet configuration |
| */ |
| #define CONFIG_MPC5xxx_FEC 1 |
| #define CONFIG_MPC5xxx_FEC_SEVENWIRE |
| /* dummy, 7-wire FEC does not have phy address */ |
| #define CONFIG_PHY_ADDR 0x00 |
| |
| /* |
| * GPIO configuration |
| * |
| * CS1: SDRAM CS1 disabled, gpio_wkup_6 enabled 0 |
| * Reserved 0 |
| * ALTs: CAN1/2 on PSC2, SPI on PSC3 00 |
| * CS7: Interrupt GPIO on PSC3_5 0 |
| * CS8: Interrupt GPIO on PSC3_4 0 |
| * ATA: reset default, changed in ATA driver 00 |
| * IR_USB_CLK: IrDA/USB 48MHz clock gen. int., pin is GPIO 0 |
| * IRDA: reset default, changed in IrDA driver 000 |
| * ETHER: reset default, changed in Ethernet driver 0000 |
| * PCI_DIS: reset default, changed in PCI driver 0 |
| * USB_SE: reset default, changed in USB driver 0 |
| * USB: reset default, changed in USB driver 00 |
| * PSC3: SPI and UART functionality without CD 1100 |
| * Reserved 0 |
| * PSC2: CAN1/2 001 |
| * Reserved 0 |
| * PSC1: reset default, changed in AC'97 driver 000 |
| * |
| */ |
| #define CONFIG_SYS_GPS_PORT_CONFIG 0x00000C10 |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| |
| #define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| # define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| |
| /* |
| * Various low-level settings |
| */ |
| #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI |
| #define CONFIG_SYS_HID0_FINAL HID0_ICE |
| |
| #if CONFIG_TOTAL5200_REV==1 |
| # define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE |
| # define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ |
| # define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ |
| # define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE |
| # define CONFIG_SYS_CS0_SIZE 0x02000000 /* 32 MB */ |
| #else |
| # define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS4_START + CONFIG_SYS_CS4_SIZE) |
| # define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ |
| # define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ |
| # define CONFIG_SYS_CS4_START (CONFIG_SYS_CS5_START + CONFIG_SYS_CS5_SIZE) |
| # define CONFIG_SYS_CS4_SIZE 0x02000000 /* 32 MB */ |
| # define CONFIG_SYS_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ |
| # define CONFIG_SYS_CS5_START CONFIG_SYS_FLASH_BASE |
| # define CONFIG_SYS_CS5_SIZE 0x02000000 /* 32 MB */ |
| # define CONFIG_SYS_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ |
| #endif |
| |
| #define CONFIG_SYS_CS1_START CONFIG_SYS_FPGA_BASE |
| #define CONFIG_SYS_CS1_SIZE 0x00010000 /* 64 kB */ |
| #define CONFIG_SYS_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */ |
| |
| #define CONFIG_SYS_CS2_START CONFIG_SYS_LCD_BASE |
| #define CONFIG_SYS_CS2_SIZE 0x00400000 /* 4096 kB */ |
| #define CONFIG_SYS_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */ |
| |
| #if CONFIG_TOTAL5200_REV==1 |
| # define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE |
| # define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ |
| # define CONFIG_SYS_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */ |
| #else |
| # define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE |
| # define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ |
| # define CONFIG_SYS_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */ |
| #endif |
| |
| #define CONFIG_SYS_CS_BURST 0x00000000 |
| #define CONFIG_SYS_CS_DEADCYCLE 0x33333333 |
| |
| /*----------------------------------------------------------------------- |
| * USB stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_USB_CLOCK 0x0001BBBB |
| #define CONFIG_USB_CONFIG 0x00001000 |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff Supports IDE harddisk |
| *----------------------------------------------------------------------- |
| */ |
| |
| #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| |
| #define CONFIG_IDE_RESET /* reset for ide supported */ |
| #define CONFIG_IDE_PREINIT |
| |
| #define CONFIG_SYS_ATA_CS_ON_I2C2 |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA |
| |
| /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) |
| |
| /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) |
| |
| /* Offset for alternate registers */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) |
| |
| /* Interval between registers */ |
| #define CONFIG_SYS_ATA_STRIDE 4 |
| |
| #endif /* __CONFIG_H */ |