blob: 340b847b9183fe5f89a2ac7e14167f819b5c7ad4 [file] [log] [blame]
/*
* (C) Copyright 2004
* DAVE Srl
*
* http://www.dave-tech.it
* http://www.wawnet.biz
* mailto:info@wawnet.biz
*
* Configuation settings for the B2 board.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_ARM7 1 /* This is a ARM7 CPU */
#define CONFIG_B2 1 /* on an B2 Board */
#define CONFIG_ARM_THUMB 1 /* this is an ARM7TDMI */
#undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */
#define CONFIG_S3C44B0_CLOCK_SPEED 75 /* we have a 75Mhz S3C44B0*/
#undef CONFIG_USE_IRQ /* don't need them anymore */
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
#define CONFIG_ENV_SIZE 1024 /* 1024 bytes may be used for env vars*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024 )
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
*/
#define CONFIG_DRIVER_LAN91C96
#define CONFIG_LAN91C96_BASE 0x04000300 /* base address */
#define CONFIG_SMC_USE_32_BIT
#undef CONFIG_SHOW_ACTIVITY
#define CONFIG_NET_RETRY_COUNT 10 /* # of retries */
/*
* select serial console configuration
*/
#define CONFIG_SERIAL1 1 /* we use Serial line 1 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ELF
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_BOOTDELAY 5
#define CONFIG_ETHADDR 00:50:c2:1e:af:fb
#define CONFIG_BOOTARGS "setenv bootargs root=/dev/ram ip=192.168.0.70:::::eth0:off \
ether=25,0,0,0,eth0 ethaddr=00:50:c2:1e:af:fb"
#define CONFIG_NETMASK 255.255.0.0
#define CONFIG_IPADDR 192.168.0.70
#define CONFIG_SERVERIP 192.168.0.23
#define CONFIG_BOOTFILE "B2-rootfs/usr/B2-zImage.u-boot"
#define CONFIG_BOOTCOMMAND "bootm 20000 f0000"
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0C400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C800000 /* 4 ... 8 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x0c700000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* 1 kHz */
/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Stack sizes
*
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#ifdef CONFIG_USE_IRQ
#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
#endif
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 banks of DRAM */
#define PHYS_SDRAM_1 0xc0000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x00400000 /* 4 MB */
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET 0x0 /* environment starts at the beginning of the EEPROM */
/*-----------------------------------------------------------------------
* I2C EEPROM (STM24C02W6) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0xFE
#define CONFIG_SYS_I2C_EEPROM_ADDR 0xA8 /* EEPROM STM24C02W6 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
/* last 4 bits of the address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/* Flash banks JFFS2 should use */
/*
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 2
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
*/
/*
Linux TAGs (see lib_arm/armlinux.c)
*/
#define CONFIG_CMDLINE_TAG
#undef CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#endif /* __CONFIG_H */