include/configs/picosam9g45.h - github/trini/u-boot - Gitiles

 /*
  * Configuration settings for the mini-box PICOSAM9G45 board.
  * (C) Copyright 2015 Inter Act B.V.
  *
  * Based on:
  * U-Boot file: include/configs/at91sam9m10g45ek.h
  * (C) Copyright 2007-2008
  * Stelian Pop <stelian@popies.net>
  * Lead Tech Design <www.leadtechdesign.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #include <asm/hardware.h>

 #define CONFIG_SYS_TEXT_BASE		0x23f00000

 #define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */

 /* ARM asynchronous clock */
 #define CONFIG_SYS_AT91_SLOW_CLOCK      32768
 #define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */

 #define CONFIG_PICOSAM

 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs	*/
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 #define CONFIG_SKIP_LOWLEVEL_INIT
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_DISPLAY_CPUINFO

 #define CONFIG_CMD_BOOTZ
 #define CONFIG_OF_LIBFDT


 /* general purpose I/O */
 #define CONFIG_ATMEL_LEGACY		/* required until (g)pio is fixed */
 #define CONFIG_AT91_GPIO
 #define CONFIG_AT91_GPIO_PULLUP	1	/* keep pullups on peripheral pins */

 /* serial console */
 #define CONFIG_ATMEL_USART
 #define CONFIG_USART_BASE		ATMEL_BASE_DBGU
 #define	CONFIG_USART_ID			ATMEL_ID_SYS

 /* LCD */
 #define CONFIG_LCD
 #define LCD_BPP				LCD_COLOR8
 #define CONFIG_LCD_LOGO
 #undef LCD_TEST_PATTERN
 #define CONFIG_LCD_INFO
 #define CONFIG_LCD_INFO_BELOW_LOGO
 #define CONFIG_SYS_WHITE_ON_BLACK
 #define CONFIG_ATMEL_LCD
 #define CONFIG_ATMEL_LCD_RGB565
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 /* board specific(not enough SRAM) */
 #define CONFIG_AT91SAM9G45_LCD_BASE		0x23E00000

 /* LED */
 #define CONFIG_AT91_LED
 #define CONFIG_GREEN_LED	AT91_PIN_PD31	/* this is the user1 led */

 #define CONFIG_BOOTDELAY	3

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 /* Enable the watchdog */
 #define CONFIG_AT91SAM9_WATCHDOG
 #define CONFIG_HW_WATCHDOG

 /*
  * Command line configuration.
  */

 /* No NOR flash */
 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_USB

 /* SDRAM */
 #define CONFIG_NR_DRAM_BANKS	2
 #define PHYS_SDRAM_1		ATMEL_BASE_CS1	/* on DDRSDRC1 */
 #define PHYS_SDRAM_1_SIZE	0x08000000	/* 128 MB */
 #define PHYS_SDRAM_2		ATMEL_BASE_CS6	/* on DDRSDRC0 */
 #define PHYS_SDRAM_2_SIZE       0x08000000	/* 128 MB */
 #define CONFIG_SYS_SDRAM_BASE	PHYS_SDRAM_1

 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)

 /* MMC */
 #define CONFIG_CMD_MMC

 #ifdef CONFIG_CMD_MMC
 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
 #define CONFIG_GENERIC_ATMEL_MCI
 #endif

 #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
 #define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif

 /* Ethernet */
 #define CONFIG_MACB
 #define CONFIG_RMII
 #define CONFIG_NET_RETRY_COUNT		20
 #define CONFIG_RESET_PHY_R
 #define CONFIG_AT91_WANTS_COMMON_PHY

 /* USB */
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_ATMEL
 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	2
 #define CONFIG_USB_STORAGE

 #define CONFIG_SYS_LOAD_ADDR		0x22000000	/* load address */

 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
 #define CONFIG_SYS_MEMTEST_END		0x23e00000

 #ifdef CONFIG_SYS_USE_MMC
 /* bootstrap + u-boot + env + linux in mmc */
 #define FAT_ENV_INTERFACE	"mmc"
 /*
  * We don't specify the part number, if device 0 has partition table, it means
  * the first partition; it no partition table, then take whole device as a
  * FAT file system.
  */
 #define FAT_ENV_DEVICE_AND_PART	"0"
 #define FAT_ENV_FILE		"uboot.env"
 #define CONFIG_ENV_IS_IN_FAT
 #define CONFIG_FAT_WRITE
 #define CONFIG_ENV_SIZE		0x4000

 #define CONFIG_BOOTARGS		"console=ttyS0,115200 " \
 				"root=/dev/mmcblk0p2 rw rootwait"
 #define CONFIG_BOOTCOMMAND	"fatload mmc 0:1 0x21000000 dtb; " \
 				"fatload mmc 0:1 0x22000000 zImage; " \
 				"bootz 0x22000000 - 0x21000000"
 #endif

 #define CONFIG_BAUDRATE			115200

 #define CONFIG_SYS_CBSIZE	256
 #define CONFIG_SYS_MAXARGS	16
 #define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE  \
 					+ sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_HUSH_PARSER

 /*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN	ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)

 /* Defines for SPL */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x300000
 #define CONFIG_SPL_MAX_SIZE		0x010000
 #define CONFIG_SPL_STACK		0x310000

 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_WATCHDOG_SUPPORT

 #define CONFIG_SYS_MONITOR_LEN		0x80000

 #ifdef CONFIG_SYS_USE_MMC

 #define CONFIG_SPL_BSS_START_ADDR	0x20000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x00080000
 #define CONFIG_SYS_SPL_MALLOC_START	0x20080000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x00080000

 #define CONFIG_SPL_LDSCRIPT	arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x400
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
 #define CONFIG_SPL_FAT_SUPPORT
 #define CONFIG_SPL_LIBDISK_SUPPORT

 #define CONFIG_SPL_ATMEL_SIZE
 #define CONFIG_SYS_MASTER_CLOCK		132096000
 #define CONFIG_SYS_AT91_PLLA		0x20c73f03
 #define CONFIG_SYS_MCKR			0x1301
 #define CONFIG_SYS_MCKR_CSS		0x1302

 #endif
 #endif
	/*
	* Configuration settings for the mini-box PICOSAM9G45 board.
	* (C) Copyright 2015 Inter Act B.V.
	*
	* Based on:
	* U-Boot file: include/configs/at91sam9m10g45ek.h
	* (C) Copyright 2007-2008
	* Stelian Pop <stelian@popies.net>
	* Lead Tech Design <www.leadtechdesign.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#include <asm/hardware.h>

	#define CONFIG_SYS_TEXT_BASE 0x23f00000

	#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */

	/* ARM asynchronous clock */
	#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
	#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */

	#define CONFIG_PICOSAM

	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG
	#define CONFIG_SKIP_LOWLEVEL_INIT
	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_DISPLAY_CPUINFO

	#define CONFIG_CMD_BOOTZ
	#define CONFIG_OF_LIBFDT


	/* general purpose I/O */
	#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
	#define CONFIG_AT91_GPIO
	#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */

	/* serial console */
	#define CONFIG_ATMEL_USART
	#define CONFIG_USART_BASE ATMEL_BASE_DBGU
	#define CONFIG_USART_ID ATMEL_ID_SYS

	/* LCD */
	#define CONFIG_LCD
	#define LCD_BPP LCD_COLOR8
	#define CONFIG_LCD_LOGO
	#undef LCD_TEST_PATTERN
	#define CONFIG_LCD_INFO
	#define CONFIG_LCD_INFO_BELOW_LOGO
	#define CONFIG_SYS_WHITE_ON_BLACK
	#define CONFIG_ATMEL_LCD
	#define CONFIG_ATMEL_LCD_RGB565
	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
	/* board specific(not enough SRAM) */
	#define CONFIG_AT91SAM9G45_LCD_BASE 0x23E00000

	/* LED */
	#define CONFIG_AT91_LED
	#define CONFIG_GREEN_LED AT91_PIN_PD31 /* this is the user1 led */

	#define CONFIG_BOOTDELAY 3

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	/* Enable the watchdog */
	#define CONFIG_AT91SAM9_WATCHDOG
	#define CONFIG_HW_WATCHDOG

	/*
	* Command line configuration.
	*/

	/* No NOR flash */
	#define CONFIG_SYS_NO_FLASH
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_USB

	/* SDRAM */
	#define CONFIG_NR_DRAM_BANKS 2
	#define PHYS_SDRAM_1 ATMEL_BASE_CS1 /* on DDRSDRC1 */
	#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
	#define PHYS_SDRAM_2 ATMEL_BASE_CS6 /* on DDRSDRC0 */
	#define PHYS_SDRAM_2_SIZE 0x08000000 /* 128 MB */
	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1

	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)

	/* MMC */
	#define CONFIG_CMD_MMC

	#ifdef CONFIG_CMD_MMC
	#define CONFIG_MMC
	#define CONFIG_GENERIC_MMC
	#define CONFIG_GENERIC_ATMEL_MCI
	#endif

	#if defined(CONFIG_CMD_USB) \|\| defined(CONFIG_CMD_MMC)
	#define CONFIG_CMD_FAT
	#define CONFIG_DOS_PARTITION
	#endif

	/* Ethernet */
	#define CONFIG_MACB
	#define CONFIG_RMII
	#define CONFIG_NET_RETRY_COUNT 20
	#define CONFIG_RESET_PHY_R
	#define CONFIG_AT91_WANTS_COMMON_PHY

	/* USB */
	#define CONFIG_USB_EHCI
	#define CONFIG_USB_EHCI_ATMEL
	#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
	#define CONFIG_USB_STORAGE

	#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */

	#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
	#define CONFIG_SYS_MEMTEST_END 0x23e00000

	#ifdef CONFIG_SYS_USE_MMC
	/* bootstrap + u-boot + env + linux in mmc */
	#define FAT_ENV_INTERFACE "mmc"
	/*
	* We don't specify the part number, if device 0 has partition table, it means
	* the first partition; it no partition table, then take whole device as a
	* FAT file system.
	*/
	#define FAT_ENV_DEVICE_AND_PART "0"
	#define FAT_ENV_FILE "uboot.env"
	#define CONFIG_ENV_IS_IN_FAT
	#define CONFIG_FAT_WRITE
	#define CONFIG_ENV_SIZE 0x4000

	#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
	"root=/dev/mmcblk0p2 rw rootwait"
	#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 dtb; " \
	"fatload mmc 0:1 0x22000000 zImage; " \
	"bootz 0x22000000 - 0x21000000"
	#endif

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_SYS_CBSIZE 256
	#define CONFIG_SYS_MAXARGS 16
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
	+ sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_LONGHELP
	#define CONFIG_CMDLINE_EDITING
	#define CONFIG_AUTO_COMPLETE
	#define CONFIG_SYS_HUSH_PARSER

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)

	/* Defines for SPL */
	#define CONFIG_SPL_FRAMEWORK
	#define CONFIG_SPL_TEXT_BASE 0x300000
	#define CONFIG_SPL_MAX_SIZE 0x010000
	#define CONFIG_SPL_STACK 0x310000

	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_SERIAL_SUPPORT
	#define CONFIG_SPL_GPIO_SUPPORT
	#define CONFIG_SPL_WATCHDOG_SUPPORT

	#define CONFIG_SYS_MONITOR_LEN 0x80000

	#ifdef CONFIG_SYS_USE_MMC

	#define CONFIG_SPL_BSS_START_ADDR 0x20000000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
	#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000

	#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
	#define CONFIG_SPL_MMC_SUPPORT
	#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
	#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
	#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
	#define CONFIG_SPL_FAT_SUPPORT
	#define CONFIG_SPL_LIBDISK_SUPPORT

	#define CONFIG_SPL_ATMEL_SIZE
	#define CONFIG_SYS_MASTER_CLOCK 132096000
	#define CONFIG_SYS_AT91_PLLA 0x20c73f03
	#define CONFIG_SYS_MCKR 0x1301
	#define CONFIG_SYS_MCKR_CSS 0x1302

	#endif
	#endif