| /* U-boot for BlackVME. (C) Wojtek Skulski 2010. |
| * The board includes ADSP-BF561 rev. 0.5, |
| * 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG), |
| * Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell), |
| * SPI boot flash on PF2 (M25P64 8MB, or M25P128 16 MB), |
| * FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB), |
| * Spartan6-LX150 (memory-mapped; both PPIs also connected). |
| * See http://www.skutek.com |
| */ |
| |
| #ifndef __CONFIG_BLACKVME_H__ |
| #define __CONFIG_BLACKVME_H__ |
| |
| #include <asm/config-pre.h> |
| |
| /* Debugging: Set these options if you're having problems |
| * #define CONFIG_DEBUG_EARLY_SERIAL |
| * #define DEBUG |
| * #define CONFIG_DEBUG_DUMP |
| * #define CONFIG_DEBUG_DUMP_SYMS |
| * CONFIG_PANIC_HANG means that the board will not auto-reboot |
| */ |
| #define CONFIG_PANIC_HANG 0 |
| |
| /* CPU Options */ |
| #define CONFIG_BFIN_CPU bf561-0.5 |
| #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER |
| |
| /* |
| * CLOCK SETTINGS CAVEAT |
| * You CANNOT just change the clock settings, esp. the SCLK. |
| * The SDRAM timing, SPI baud, and the serial UART baud |
| * use SCLK frequency to set their own frequencies. Therefore, |
| * if you change the SCLK_DIV, you may also have to adjust |
| * SDRAM refresh and other timings. |
| * -------------------------------------------------------------- |
| * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV |
| * 25 * 8 / 1 = 200 MHz |
| * 25 * 16 / 1 = 400 MHz |
| * 25 * 24 / 1 = 600 MHz |
| * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV |
| * 25 * 8 / 2 = 100 MHz |
| * 25 * 24 / 6 = 100 MHz |
| * 25 * 24 / 5 = 120 MHz |
| * 25 * 16 / 3 = 133 MHz |
| * 25 MHz because the oscillator also feeds the ether chip. |
| * CONFIG_CLKIN_HZ is 25 MHz written in Hz |
| * CLKIN_HALF controls the DF bit in PLL_CTL |
| * 0 = CLKIN 1 = CLKIN / 2 |
| * PLL_BYPASS controls the BYPASS bit in PLL_CTL |
| * 0 = do not bypass 1 = bypass PLL |
| * VCO_MULT = MSEL (multiplier) in PLL_CTL |
| * Values can range from 0-63 (where 0 means 64) |
| * CCLK_DIV = core clock divider (1, 2, 4, or 8 ONLY) |
| * SCLK_DIV = system clock divider, 1 to 15 |
| */ |
| #define CONFIG_CLKIN_HZ 25000000 |
| #define CONFIG_CLKIN_HALF 0 |
| #define CONFIG_PLL_BYPASS 0 |
| #define CONFIG_VCO_MULT 8 |
| #define CONFIG_CCLK_DIV 1 |
| #define CONFIG_SCLK_DIV 2 |
| |
| /* |
| * Ether chip in async memory space AMS3, same as BF561-EZ-KIT. |
| * Used in 32-bit mode. 16-bit mode not supported. |
| * http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180 |
| */ |
| /* |
| * Network settings using a dedicated 2nd ether card in PC |
| * Windows will automatically acquire IP of that card |
| * Then use the dedicated card IP + 1 for the board |
| * http://docs.blackfin.uclinux.org/doku.php?id=setting_up_the_network |
| */ |
| #define CONFIG_DRIVER_AX88180 1 |
| #define AX88180_BASE 0x2c000000 |
| #define CONFIG_CMD_MII /* enable probing PHY */ |
| |
| #define CONFIG_HOSTNAME blackvme /* Bfin board */ |
| #define CONFIG_IPADDR 169.254.144.145 /* Bfin board */ |
| #define CONFIG_GATEWAYIP 169.254.144.144 /* dedic card */ |
| #define CONFIG_SERVERIP 169.254.144.144 /* tftp server */ |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_ROOTPATH "/export/uClinux-dist/romfs" /*NFS*/ |
| #define CFG_AUTOLOAD "no" |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_PING |
| |
| /* |
| * SDRAM settings & memory map |
| */ |
| |
| #define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ |
| #define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ |
| /* |
| * SDRAM reference page |
| * http://docs.blackfin.uclinux.org/doku.php?id=bfin:sdram |
| * NOTE: BlackVME populates only SDRAM bank 0 |
| */ |
| /* CONFIG_EBIU_SDBCTL_VAL bank ctrl may be needed in future */ |
| #define CONFIG_EBIU_SDGCTL_VAL 0x91114d /* global control */ |
| #define CONFIG_EBIU_SDRRC_VAL 0x306 /* refresh rate */ |
| |
| /* Async memory global settings. (ASRAM, not SDRAM) |
| * HRM page 16-10. Global ASRAM control = 0x3F. Six lower bits = 1 |
| * CLKOUT enabled, all async banks enabled, core has priority |
| * bank 0&1 16 bit (FPGA) |
| * bank 2&3 32 bit (ether and USB chips) |
| */ |
| #define CONFIG_EBIU_AMGCTL_VAL 0x3F /* ASRAM setup */ |
| |
| /* Async mem timing: BF561 HRM page 16-12 and 16-15. |
| * Default values 0xFFC2 FFC2 are the slowest supported. |
| * Example settings of CONFIG_EBIU_AMBCTL1_VAL |
| * 1. EZ-KIT settings: 0xFFC2 7BB0 |
| * 2. Bank 3 good timing for AX88180 @ 125MHz = 0x8850 xxxx |
| * See the following page: |
| * http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180 |
| * 3. Bank 3 timing for AX88180 @ SCLK = 100 MHz: |
| * AX88180 WEN = 5 clocks REN 6 clocks @ SCLK = 100 MHz |
| * One extra clock needed because AX88180 is asynchronous to CPU. |
| */ |
| /* bank 1 0 */ |
| #define CONFIG_EBIU_AMBCTL0_VAL 0xFFC2FFC2 |
| /* bank 3 2 */ |
| #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC2FFC2 |
| |
| /* memory layout */ |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) |
| #define CONFIG_SYS_MALLOC_LEN (384 << 10) |
| |
| /* |
| * Serial SPI Flash |
| * For the M25P64 SCK should be kept < 15 MHz |
| */ |
| #define CONFIG_BFIN_SPI |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_OFFSET 0x40000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x40000 |
| |
| #define CONFIG_ENV_SPI_MAX_HZ 15000000 |
| #define CONFIG_SF_DEFAULT_SPEED 15000000 |
| |
| /* |
| * Interactive command settings |
| */ |
| |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_CMDLINE_EDITING 1 |
| #define CONFIG_AUTO_COMPLETE 1 |
| |
| #define CONFIG_CMD_BOOTLDR |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_CPLBINFO |
| #define CONFIG_CMD_SF |
| |
| /* |
| * Default: boot from SPI flash. |
| * "sfboot" is a composite command defined in extra settings |
| */ |
| #define CONFIG_BOOTDELAY 5 |
| #define CONFIG_BOOTCOMMAND "run sfboot" |
| |
| /* |
| * Console settings |
| */ |
| #define CONFIG_BAUDRATE 57600 |
| #define CONFIG_LOADS_ECHO 1 |
| #define CONFIG_UART_CONSOLE 0 |
| #define CONFIG_BFIN_SERIAL |
| |
| /* |
| * U-Boot environment variables. Use "printenv" to examine. |
| * http://docs.blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:env |
| */ |
| #define CONFIG_BOOTARGS \ |
| "root=/dev/mtdblock0 rw " \ |
| "clkin_hz=" __stringify(CONFIG_CLKIN_HZ) " " \ |
| "earlyprintk=serial,uart0," \ |
| __stringify(CONFIG_BAUDRATE) " " \ |
| "console=ttyBF0," __stringify(CONFIG_BAUDRATE) " " |
| |
| /* Convenience env variables & commands. |
| * Reserve kernstart = 0x20000 = 128 kB for U-Boot. |
| * Reserve kernarea = 0x500000 = 5 MB for kernel (reasonable size). |
| * U-Boot image is saved at flash offset=0. |
| * Kernel image is saved at flash offset=$kernstart. |
| * Instructions. Ksave takes about a minute to complete. |
| * 1. Update U-Boot: run uget; run usave |
| * 2. Update kernel: run kget; run ksave |
| * After updating U-Boot also update the kernel per above instructions |
| * to make the saved environment consistent with the flash. |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "kernstart=0x20000\0" \ |
| "kernarea=0x500000\0" \ |
| "uget=tftp u-boot.ldr\0" \ |
| "kget=tftp uImage\0" \ |
| "usave=sf probe 2; " \ |
| "sf erase 0 $(kernstart); " \ |
| "sf write $(fileaddr) 0 $(filesize)\0" \ |
| "ksave=sf probe 2; " \ |
| "saveenv; " \ |
| "echo Now patiently wait for the prompt...; " \ |
| "sf erase $(kernstart) $(kernarea); " \ |
| "sf write $(fileaddr) $(kernstart) $(filesize)\0" \ |
| "sfboot=sf probe 2; " \ |
| "sf read $(loadaddr) $(kernstart) $(filesize); " \ |
| "run addip; bootm\0" \ |
| "addip=setenv bootargs $(bootargs) " \ |
| "ip=$(ipaddr):$(serverip):$(gatewayip):" \ |
| "$(netmask):$(hostname):eth0:off\0" |
| |
| /* |
| * Soft I2C settings (BF561 does not have hard I2C) |
| * PF12,13 on SPI connector 0. |
| */ |
| #ifdef CONFIG_SYS_I2C_SOFT |
| # define CONFIG_CMD_I2C |
| # define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF12 |
| # define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF13 |
| # define CONFIG_SYS_I2C_SPEED 50000 |
| # define CONFIG_SYS_I2C_SLAVE 0xFE |
| #endif |
| |
| /* |
| * No Parallel Flash on this board |
| */ |
| #define CONFIG_SYS_NO_FLASH |
| #undef CONFIG_CMD_JFFS2 |
| |
| #endif |