| /* |
| * (C) Copyright 2001 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC824X 1 |
| /* #define CONFIG_MPC8240 1 */ |
| #define CONFIG_MPC8245 1 |
| #define CONFIG_EXALION 1 |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFF00000 |
| |
| #if defined (CONFIG_MPC8240) |
| /* #warning ---------- eXalion with MPC8240 --------------- */ |
| #elif defined (CONFIG_MPC8245) |
| /* #warning ++++++++++ eXalion with MPC8245 +++++++++++++++ */ |
| #elif defined (CONFIG_MPC8245) && defined (CONFIG_MPC8245) |
| #error #### Both types of MPC824x defined (CONFIG_8240 and CONFIG_8245) |
| #else |
| #error #### Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) |
| #endif |
| /* older kernels need clock in MHz newer in Hz */ |
| /* #define CONFIG_CLOCKS_IN_MHZ 1 */ /* clocks passsed to Linux in MHz */ |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| #define CONFIG_BOOTDELAY 10 |
| |
| |
| /*#define CONFIG_DRAM_SPEED 66 */ /* MHz */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_SDRAM |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_SAVEENV |
| #define CONFIG_CMD_PCI |
| |
| |
| /*----------------------------------------------------------------------- |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP 1 /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 8 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ |
| #define CONFIG_MISC_INIT_R 1 |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 1 GBytes - initdram() will */ |
| /* return real value. */ |
| |
| #define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 |
| |
| #undef CONFIG_SYS_RAMBOOT |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area |
| */ |
| #define CONFIG_SYS_INIT_DATA_SIZE 128 |
| |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 |
| #define CONFIG_SYS_INIT_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_DATA_SIZE) |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| |
| #if defined (CONFIG_MPC8240) |
| #define CONFIG_SYS_FLASH_BASE 0xFFE00000 |
| #define CONFIG_SYS_FLASH_SIZE (2 * 1024 * 1024) /* onboard 2MByte flash */ |
| #elif defined (CONFIG_MPC8245) |
| #define CONFIG_SYS_FLASH_BASE 0xFFC00000 |
| #define CONFIG_SYS_FLASH_SIZE (4 * 1024 * 1024) /* onboard 4MByte flash */ |
| #else |
| #error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) |
| #endif |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* Size of one Flash sector */ |
| #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE /* Use one Flash sector for environment */ |
| #define CONFIG_ENV_ADDR 0xFFFC0000 |
| #define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */ |
| |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ |
| |
| #define CONFIG_SYS_ALT_MEMTEST 1 /* use real memory test */ |
| #define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ |
| |
| #define CONFIG_SYS_EUMB_ADDR 0xFC000000 |
| |
| /* #define CONFIG_SYS_ISA_MEM 0xFD000000 */ |
| #define CONFIG_SYS_ISA_IO 0xFE000000 |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors per flash */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE |
| #define FLASH_BASE1_PRELIM 0 |
| |
| |
| /*----------------------------------------------------------------------- |
| * FLASH and environment organization |
| */ |
| |
| #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| */ |
| #define CONFIG_PCI 1 /* include pci support */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ |
| #undef CONFIG_PCI_PNP |
| |
| |
| #define CONFIG_EEPRO100 1 |
| |
| #define PCI_ENET0_MEMADDR 0x80000000 /* Intel 82559ER */ |
| #define PCI_ENET0_IOADDR 0x80000000 |
| #define PCI_ENET1_MEMADDR 0x81000000 /* Intel 82559ER */ |
| #define PCI_ENET1_IOADDR 0x81000000 |
| #define PCI_ENET2_MEMADDR 0x82000000 /* Broadcom BCM569xx */ |
| #define PCI_ENET2_IOADDR 0x82000000 |
| #define PCI_ENET3_MEMADDR 0x83000000 /* Broadcom BCM56xx */ |
| #define PCI_ENET3_IOADDR 0x83000000 |
| |
| /*----------------------------------------------------------------------- |
| * NS16550 Configuration |
| */ |
| #define CONFIG_SYS_NS16550 1 |
| #define CONFIG_SYS_NS16550_SERIAL 1 |
| |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_BAUDRATE 38400 |
| |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| |
| #if (CONFIG_CONS_INDEX == 1) |
| #define CONFIG_SYS_NS16550_CLK 1843200 /* COM1 only ! */ |
| #else |
| #define CONFIG_SYS_NS16550_CLK ({ extern ulong get_bus_freq (ulong); get_bus_freq (0); }) |
| #endif |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_ISA_IO + 0x3F8) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4500) |
| #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_EUMB_ADDR + 0x4600) |
| |
| /*----------------------------------------------------------------------- |
| * select i2c support configuration |
| * |
| * Supported configurations are {none, software, hardware} drivers. |
| * If the software driver is chosen, there are some additional |
| * configuration items that the driver uses to drive the port pins. |
| */ |
| #define CONFIG_HARD_I2C 1 /* To enable I2C support */ |
| #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| |
| /*----------------------------------------------------------------------- |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| #define CONFIG_SYS_HZ 1000 |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| #define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2 /* for MPC8240 only */ |
| |
| /*#define CONFIG_133MHZ_DRAM 1 */ /* For 133 MHZ DRAM only !!!!!!!!!!! */ |
| |
| #if defined (CONFIG_MPC8245) |
| /* Bit-field values for PMCR2. */ |
| #if defined (CONFIG_133MHZ_DRAM) |
| #define CONFIG_SYS_DLL_EXTEND 0x80 /* use DLL extended range - 133MHz only */ |
| #define CONFIG_SYS_PCI_HOLD_DEL 0x20 /* delay and hold timing - 133MHz only */ |
| #endif |
| |
| /* Bit-field values for MIOCR1. */ |
| #if !defined (CONFIG_133MHZ_DRAM) |
| #define CONFIG_SYS_DLL_MAX_DELAY 0x04 /* longer DLL delay line - 66MHz only */ |
| #endif |
| /* Bit-field values for MIOCR2. */ |
| #define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay */ |
| /* - note bottom 3 bits MUST be 0 */ |
| #endif |
| |
| /* Bit-field values for MCCR1. */ |
| #define CONFIG_SYS_ROMNAL 7 /*rom/flash next access time */ |
| #define CONFIG_SYS_ROMFAL 11 /*rom/flash access time */ |
| |
| /* Bit-field values for MCCR2. */ |
| #define CONFIG_SYS_TSWAIT 0x5 /* Transaction Start Wait States timer */ |
| #if defined (CONFIG_133MHZ_DRAM) |
| #define CONFIG_SYS_REFINT 1300 /* no of clock cycles between CBR */ |
| #else /* refresh cycles */ |
| #define CONFIG_SYS_REFINT 750 |
| #endif |
| |
| /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ |
| #if defined (CONFIG_133MHZ_DRAM) |
| #define CONFIG_SYS_BSTOPRE 1023 |
| #else |
| #define CONFIG_SYS_BSTOPRE 250 |
| #endif |
| |
| /* Bit-field values for MCCR3. */ |
| /* the following are for SDRAM only */ |
| |
| #if defined (CONFIG_133MHZ_DRAM) |
| #define CONFIG_SYS_REFREC 9 /* Refresh to activate interval */ |
| #else |
| #define CONFIG_SYS_REFREC 5 /* Refresh to activate interval */ |
| #endif |
| #if defined (CONFIG_MPC8240) |
| #define CONFIG_SYS_RDLAT 2 /* data latency from read command */ |
| #endif |
| |
| /* Bit-field values for MCCR4. */ |
| #if defined (CONFIG_133MHZ_DRAM) |
| #define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */ |
| #define CONFIG_SYS_ACTTOPRE 7 /* Activate to Precharge interval */ |
| #define CONFIG_SYS_ACTORW 5 /* Activate to R/W */ |
| #define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ |
| #else |
| #if 0 |
| #define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */ |
| #define CONFIG_SYS_ACTTOPRE 3 /* Activate to Precharge interval */ |
| #define CONFIG_SYS_ACTORW 3 /* Activate to R/W */ |
| #define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */ |
| #endif |
| #define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */ |
| #define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ |
| #define CONFIG_SYS_ACTORW 3 /* Activate to R/W */ |
| #define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ |
| #endif |
| #define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ |
| #define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */ |
| #define CONFIG_SYS_REGDIMM 0 |
| #if defined (CONFIG_MPC8240) |
| #define CONFIG_SYS_REGISTERD_TYPE_BUFFER 0 |
| #elif defined (CONFIG_MPC8245) |
| #define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 |
| #define CONFIG_SYS_EXTROM 0 |
| #else |
| #error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) |
| #endif |
| |
| |
| /*----------------------------------------------------------------------- |
| memory bank settings |
| * only bits 20-29 are actually used from these vales to set the |
| * start/end address the upper two bits will be 0, and the lower 20 |
| * bits will be set to 0x00000 for a start address, or 0xfffff for an |
| * end address |
| */ |
| #define CONFIG_SYS_BANK0_START 0x00000000 |
| #define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) |
| #define CONFIG_SYS_BANK0_ENABLE 1 |
| #define CONFIG_SYS_BANK1_START 0x3ff00000 |
| #define CONFIG_SYS_BANK1_END 0x3fffffff |
| #define CONFIG_SYS_BANK1_ENABLE 0 |
| #define CONFIG_SYS_BANK2_START 0x3ff00000 |
| #define CONFIG_SYS_BANK2_END 0x3fffffff |
| #define CONFIG_SYS_BANK2_ENABLE 0 |
| #define CONFIG_SYS_BANK3_START 0x3ff00000 |
| #define CONFIG_SYS_BANK3_END 0x3fffffff |
| #define CONFIG_SYS_BANK3_ENABLE 0 |
| #define CONFIG_SYS_BANK4_START 0x00000000 |
| #define CONFIG_SYS_BANK4_END 0x00000000 |
| #define CONFIG_SYS_BANK4_ENABLE 0 |
| #define CONFIG_SYS_BANK5_START 0x00000000 |
| #define CONFIG_SYS_BANK5_END 0x00000000 |
| #define CONFIG_SYS_BANK5_ENABLE 0 |
| #define CONFIG_SYS_BANK6_START 0x00000000 |
| #define CONFIG_SYS_BANK6_END 0x00000000 |
| #define CONFIG_SYS_BANK6_ENABLE 0 |
| #define CONFIG_SYS_BANK7_START 0x00000000 |
| #define CONFIG_SYS_BANK7_END 0x00000000 |
| #define CONFIG_SYS_BANK7_ENABLE 0 |
| |
| /*----------------------------------------------------------------------- |
| * Memory bank enable bitmask, specifying which of the banks defined above |
| are actually present. MSB is for bank #7, LSB is for bank #0. |
| */ |
| #define CONFIG_SYS_BANK_ENABLE 0x01 |
| |
| #if defined (CONFIG_MPC8240) |
| #define CONFIG_SYS_ODCR 0xDF /* configures line driver impedances, */ |
| /* see 8240 book for bit definitions */ |
| #elif defined (CONFIG_MPC8245) |
| #if defined (CONFIG_133MHZ_DRAM) |
| #define CONFIG_SYS_ODCR 0xFE /* configures line driver impedances - 133MHz */ |
| #else |
| #define CONFIG_SYS_ODCR 0xDE /* configures line driver impedances - 66MHz */ |
| #endif |
| #else |
| #error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240) |
| #endif |
| |
| #define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */ |
| /* currently accessed page in memory */ |
| /* see 8240 book for details */ |
| |
| /*----------------------------------------------------------------------- |
| * Block Address Translation (BAT) register settings. |
| */ |
| /* SDRAM 0 - 256MB */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| /* stack in DCACHE @ 1GB (no backing mem) */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| |
| /* PCI memory */ |
| #define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| /* Flash, config addrs, etc */ |
| #define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 32 |
| #if defined(CONFIG_CMD_KGDB) |
| # define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /* values according to the manual */ |
| #define CONFIG_DRAM_50MHZ 1 |
| #define CONFIG_SDRAM_50MHZ |
| |
| #undef NR_8259_INTS |
| #define NR_8259_INTS 1 |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff |
| */ |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 2 IDE busses */ |
| #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 2 drives per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO /* base address */ |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */ |
| #define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */ |
| |
| #define CONFIG_ATAPI |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ |
| #undef CONFIG_IDE_LED /* no led for ide supported */ |
| #undef CONFIG_IDE_RESET /* reset for ide supported... */ |
| #undef CONFIG_IDE_RESET_ROUTINE /* with a special reset function */ |
| |
| /*----------------------------------------------------------------------- |
| * DISK Partition support |
| */ |
| #define CONFIG_DOS_PARTITION |
| |
| /*----------------------------------------------------------------------- |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| #endif /* __CONFIG_H */ |