| /* |
| * (C) Copyright 2010 |
| * Marvell Semiconductor <www.marvell.com> |
| * Written-by: Prafulla Wadaskar <prafulla@marvell.com> |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, |
| * MA 02110-1301 USA |
| */ |
| |
| /* |
| * This file contains Marvell Board Specific common defincations. |
| * This file should be included in board config header file. |
| * |
| * It supports common definations for Kirkwood platform |
| * TBD: support for Orion5X platforms |
| */ |
| |
| #ifndef _MV_COMMON_H |
| #define _MV_COMMON_H |
| |
| /* |
| * High Level Configuration Options (easy to change) |
| */ |
| #define CONFIG_MARVELL 1 |
| #define CONFIG_ARM926EJS 1 /* Basic Architecture */ |
| |
| /* ====> Kirkwood Platform Common Definations */ |
| #if defined(CONFIG_KIRKWOOD) |
| #define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ |
| #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ |
| #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ |
| #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ |
| |
| /* |
| * By default kwbimage.cfg from board specific folder is used |
| * If for some board, different configuration file need to be used, |
| * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file |
| */ |
| #ifndef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg |
| #endif /* CONFIG_SYS_KWD_CONFIG */ |
| |
| /* Kirkwood has 2k of Security SRAM, use it for SP */ |
| #define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 |
| #define CONFIG_NR_DRAM_BANKS_MAX 2 |
| |
| #define CONFIG_I2C_MVTWSI_BASE KW_TWSI_BASE |
| #define MV_UART_CONSOLE_BASE KW_UART0_BASE |
| #define MV_SATA_BASE KW_SATA_BASE |
| #define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET |
| #define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET |
| |
| /* ====> ARMADA100 Platform Common Definations */ |
| #elif defined (CONFIG_ARMADA100) |
| |
| #define CONFIG_SYS_TCLK (14745600) /* NS16550 clk config */ |
| #define CONFIG_SYS_HZ_CLOCK (3250000) /* Timer Freq. 3.25MHZ */ |
| #define CONFIG_MARVELL_MFP /* Enable mvmfp driver */ |
| #define MV_MFPR_BASE ARMD1_MFPR_BASE |
| #define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE |
| #define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register |
| represents UART Unit Enable */ |
| /* |
| * There is no internal RAM in ARMADA100, using DRAM |
| * TBD: dcache to be used for this |
| */ |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - 0x00200000) |
| #define CONFIG_NR_DRAM_BANKS_MAX 2 |
| |
| #else |
| #error "Unsupported SoC Platform..." |
| #endif |
| |
| /* |
| * Custom CONFIG_SYS_TEXT_BASE can be done in <board>.h |
| */ |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0x00600000 |
| #endif /* CONFIG_SYS_TEXT_BASE */ |
| |
| /* additions for new ARM relocation support */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| |
| /* |
| * CLKs configurations |
| */ |
| #define CONFIG_SYS_HZ 1000 |
| |
| /* |
| * NS16550 Configuration |
| */ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE (-4) |
| #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK |
| #define CONFIG_SYS_NS16550_COM1 MV_UART_CONSOLE_BASE |
| |
| /* |
| * Serial Port configuration |
| * The following definitions let you select what serial you want to use |
| * for your console driver. |
| */ |
| |
| #define CONFIG_CONS_INDEX 1 /*Console on UART0 */ |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ |
| 115200,230400, 460800, 921600 } |
| /* auto boot */ |
| #define CONFIG_BOOTDELAY 3 /* default enable autoboot */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ |
| #define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ |
| #define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ |
| |
| #define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ |
| +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ |
| |
| /* |
| * NAND configuration |
| */ |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_NAND_KIRKWOOD |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define NAND_MAX_CHIPS 1 |
| #define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */ |
| #define NAND_ALLOW_ERASE_ALL 1 |
| #define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ |
| #endif |
| |
| /* |
| * SPI Flash configuration |
| */ |
| #ifdef CONFIG_CMD_SF |
| #define CONFIG_SPI_FLASH 1 |
| #define CONFIG_HARD_SPI 1 |
| #define CONFIG_KIRKWOOD_SPI 1 |
| #define CONFIG_SPI_FLASH_MACRONIX 1 |
| #define CONFIG_ENV_SPI_BUS 0 |
| #define CONFIG_ENV_SPI_CS 0 |
| #define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */ |
| #endif |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */ |
| /* size in bytes reserved for initial data */ |
| |
| /* |
| * Other required minimal configurations |
| */ |
| #define CONFIG_SYS_LONGHELP |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_CMDLINE_EDITING |
| #define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ |
| #define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ |
| #ifndef CONFIG_ARMADA100 /* will be removed latter */ |
| #define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ |
| #endif /* CONFIG_ARMADA100 */ |
| #define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */ |
| #define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ |
| #define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ |
| #define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ |
| #define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */ |
| #define CONFIG_SYS_MEMTEST_END 0x00ffffff /*(_16M -1) */ |
| #define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| |
| /* |
| * DRAM Banks configuration, Custom config can be done in <board>.h |
| */ |
| #ifndef CONFIG_NR_DRAM_BANKS |
| #define CONFIG_NR_DRAM_BANKS CONFIG_NR_DRAM_BANKS_MAX |
| #else |
| #if (CONFIG_NR_DRAM_BANKS > CONFIG_NR_DRAM_BANKS_MAX) |
| #error CONFIG_NR_DRAM_BANKS Configurated more than available |
| #endif |
| #endif /* CONFIG_NR_DRAM_BANKS */ |
| |
| /* |
| * Ethernet Driver configuration |
| */ |
| #ifdef CONFIG_CMD_NET |
| #define CONFIG_CMD_MII |
| #define CONFIG_NETCONSOLE /* include NetConsole support */ |
| #define CONFIG_NET_MULTI /* specify more that one ports available */ |
| #define CONFIG_MII /* expose smi ove miiphy interface */ |
| #define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ |
| #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ |
| #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ |
| #define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ |
| #endif /* CONFIG_CMD_NET */ |
| |
| /* |
| * USB/EHCI |
| */ |
| #ifdef CONFIG_CMD_USB |
| #define CONFIG_USB_EHCI /* Enable EHCI USB support */ |
| #define CONFIG_USB_EHCI_KIRKWOOD |
| #define CONFIG_EHCI_IS_TDI |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| #define CONFIG_SUPPORT_VFAT |
| #endif /* CONFIG_CMD_USB */ |
| |
| /* |
| * IDE Support on SATA ports |
| */ |
| #ifdef CONFIG_CMD_IDE |
| #define __io |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_MVSATA_IDE |
| #define CONFIG_IDE_PREINIT |
| #define CONFIG_MVSATA_IDE_USE_PORT1 |
| /* Needs byte-swapping for ATA data register */ |
| #define CONFIG_IDE_SWAP_IO |
| /* Data, registers and alternate blocks are at the same offset */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) |
| #define CONFIG_SYS_ATA_REG_OFFSET (0x0100) |
| #define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) |
| /* Each 8-bit ATA register is aligned to a 4-bytes address */ |
| #define CONFIG_SYS_ATA_STRIDE 4 |
| /* Controller supports 48-bits LBA addressing */ |
| #define CONFIG_LBA48 |
| /* CONFIG_CMD_IDE requires some #defines for ATA registers */ |
| #define CONFIG_SYS_IDE_MAXBUS 2 |
| #define CONFIG_SYS_IDE_MAXDEVICE 2 |
| /* ATA registers base is at SATA controller base */ |
| #define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE |
| #endif /* CONFIG_CMD_IDE */ |
| |
| /* |
| * I2C related stuff |
| */ |
| #ifdef CONFIG_CMD_I2C |
| #define CONFIG_I2C_MVTWSI |
| #define CONFIG_SYS_I2C_SLAVE 0x0 |
| #define CONFIG_SYS_I2C_SPEED 100000 |
| #endif |
| |
| /* |
| * File system |
| */ |
| #ifndef CONFIG_ARMADA100 /* will be removed latter */ |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_UBI |
| #define CONFIG_CMD_UBIFS |
| #define CONFIG_RBTREE |
| #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ |
| #define CONFIG_MTD_PARTITIONS |
| #define CONFIG_CMD_MTDPARTS |
| #define CONFIG_LZO |
| #endif /* CONFIG_ARMADA100 */ |
| |
| #endif /* _MV_COMMON_H */ |