blob: d1404b2555be72a20a4bc36fd829b65c40b6461f [file] [log] [blame]
/*
* Copyright (C) 2016 NXP Semiconductors
*
* Configuration settings for the i.MX7S Warp board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __WARP7_CONFIG_H
#define __WARP7_CONFIG_H
#define CONFIG_BOOTDELAY 1
#include "mx7_common.h"
#define PHYS_SDRAM_SIZE SZ_512M
#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
#define CONFIG_BOARD_EARLY_INIT_F
/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC3_BASE_ADDR
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
#define CONFIG_DFU_ENV_SETTINGS \
"dfu_alt_info=image raw 0 0x800000;"\
"u-boot raw 0 0x4000;"\
"bootimg part 0 1;"\
"rootfs part 0 2\0" \
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_DFU_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
"console=ttymxc0\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"fdt_file=imx7d-warp.dtb\0" \
"fdt_addr=0x83000000\0" \
"boot_fdt=try\0" \
"ip_dyn=yes\0" \
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
"root=${mmcroot}\0" \
"loadbootscript=" \
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
"bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
"bootz; " \
"fi;\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev};" \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run loadimage; then " \
"run mmcboot; " \
"fi; " \
"fi; " \
"fi"
#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000)
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_HZ 1000
#define CONFIG_STACKSIZE SZ_128K
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_SIZE SZ_8K
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_ENV_OFFSET (8 * SZ_64K)
#define CONFIG_SYS_FSL_USDHC_NUM 1
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_SYS_MMC_ENV_PART 0
#define CONFIG_MMCROOT "/dev/mmcblk2p2"
/* USB Configs */
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX7
#define CONFIG_USB_STORAGE
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Only OTG1 port enabled */
#define CONFIG_IMX_THERMAL
#define CONFIG_CI_UDC
#define CONFIG_USBD_HS
#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_USB_GADGET
#define CONFIG_CMD_USB_MASS_STORAGE
#define CONFIG_USB_FUNCTION_MASS_STORAGE
#define CONFIG_USB_GADGET_DOWNLOAD
#define CONFIG_USB_GADGET_VBUS_DRAW 2
#define CONFIG_G_DNL_VENDOR_NUM 0x0525
#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
#define CONFIG_G_DNL_MANUFACTURER "FSL"
/* USB Device Firmware Update support */
#define CONFIG_CMD_DFU
#define CONFIG_USB_FUNCTION_DFU
#define CONFIG_DFU_MMC
#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_16M
#define DFU_DEFAULT_POLL_TIMEOUT 300
#endif