| /* |
| * Copyright 2014 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * T2080 RDB/PCIe board configuration file |
| */ |
| |
| #ifndef __T2080RDB_H |
| #define __T2080RDB_H |
| |
| #define CONFIG_SYS_GENERIC_BOARD |
| #define CONFIG_DISPLAY_BOARDINFO |
| #define CONFIG_T2080RDB |
| #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ |
| #define CONFIG_MMC |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_USB_EHCI |
| #define CONFIG_FSL_SATA_V2 |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_PHYS_64BIT |
| #define CONFIG_BOOKE |
| #define CONFIG_E500 /* BOOKE e500 family */ |
| #define CONFIG_E500MC /* BOOKE e500mc family */ |
| #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ |
| #define CONFIG_MP /* support multiple processors */ |
| #define CONFIG_ENABLE_36BIT_PHYS |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_ADDR_MAP 1 |
| #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ |
| #endif |
| |
| #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ |
| #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS |
| #define CONFIG_FSL_IFC /* Enable IFC Support */ |
| #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ |
| #define CONFIG_FSL_LAW /* Use common FSL init code */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg |
| #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg |
| |
| #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT |
| #define CONFIG_SPL_ENV_SUPPORT |
| #define CONFIG_SPL_SERIAL_SUPPORT |
| #define CONFIG_SPL_FLUSH_IMAGE |
| #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" |
| #define CONFIG_SPL_LIBGENERIC_SUPPORT |
| #define CONFIG_SPL_LIBCOMMON_SUPPORT |
| #define CONFIG_SPL_I2C_SUPPORT |
| #define CONFIG_SPL_DRIVERS_MISC_SUPPORT |
| #define CONFIG_FSL_LAW /* Use common FSL init code */ |
| #define CONFIG_SYS_TEXT_BASE 0x00201000 |
| #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 |
| #define CONFIG_SPL_PAD_TO 0x40000 |
| #define CONFIG_SPL_MAX_SIZE 0x28000 |
| #define RESET_VECTOR_OFFSET 0x27FFC |
| #define BOOT_PAGE_OFFSET 0x27000 |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SPL_SKIP_RELOCATE |
| #define CONFIG_SPL_COMMON_INIT_DDR |
| #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE |
| #define CONFIG_SYS_NO_FLASH |
| #endif |
| |
| #ifdef CONFIG_NAND |
| #define CONFIG_SPL_NAND_SUPPORT |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 |
| #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) |
| #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" |
| #define CONFIG_SPL_NAND_BOOT |
| #endif |
| |
| #ifdef CONFIG_SPIFLASH |
| #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC |
| #define CONFIG_SPL_SPI_SUPPORT |
| #define CONFIG_SPL_SPI_FLASH_SUPPORT |
| #define CONFIG_SPL_SPI_FLASH_MINIMAL |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) |
| #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) |
| #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MPC85XX_NO_RESETVEC |
| #endif |
| #define CONFIG_SPL_SPI_BOOT |
| #endif |
| |
| #ifdef CONFIG_SDCARD |
| #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC |
| #define CONFIG_SPL_MMC_SUPPORT |
| #define CONFIG_SPL_MMC_MINIMAL |
| #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) |
| #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) |
| #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) |
| #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MPC85XX_NO_RESETVEC |
| #endif |
| #define CONFIG_SPL_MMC_BOOT |
| #endif |
| |
| #endif /* CONFIG_RAMBOOT_PBL */ |
| |
| #define CONFIG_SRIO_PCIE_BOOT_MASTER |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| /* Set 1M boot space */ |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #define CONFIG_SYS_NO_FLASH |
| #endif |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xeff40000 |
| #endif |
| |
| #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_SYS_CACHE_STASHING |
| #define CONFIG_BTB /* toggle branch predition */ |
| #define CONFIG_DDR_ECC |
| #ifdef CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #endif |
| |
| #ifndef CONFIG_SYS_NO_FLASH |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| #endif |
| |
| #if defined(CONFIG_SPIFLASH) |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_SPI_BUS 0 |
| #define CONFIG_ENV_SPI_CS 0 |
| #define CONFIG_ENV_SPI_MAX_HZ 10000000 |
| #define CONFIG_ENV_SPI_MODE 0 |
| #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ |
| #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ |
| #define CONFIG_ENV_SECT_SIZE 0x10000 |
| #elif defined(CONFIG_SDCARD) |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_ENV_IS_IN_MMC |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_OFFSET (512 * 0x800) |
| #elif defined(CONFIG_NAND) |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_ENV_IS_IN_NAND |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) |
| #define CONFIG_ENV_IS_IN_REMOTE |
| #define CONFIG_ENV_ADDR 0xffe20000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #elif defined(CONFIG_ENV_IS_NOWHERE) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| #endif |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(void); |
| unsigned long get_board_ddr_clk(void); |
| #endif |
| |
| #define CONFIG_SYS_CLK_FREQ 66660000 |
| #define CONFIG_DDR_CLK_FREQ 133330000 |
| |
| /* |
| * Config the L3 Cache as L3 SRAM |
| */ |
| #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 |
| #define CONFIG_SYS_L3_SIZE (512 << 10) |
| #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) |
| #endif |
| #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) |
| #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) |
| #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) |
| #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) |
| |
| #define CONFIG_SYS_DCSRBAR 0xf0000000 |
| #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull |
| |
| /* EEPROM */ |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_VERY_BIG_RAM |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| #define CONFIG_DDR_SPD |
| #define CONFIG_SYS_FSL_DDR3 |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| #define CONFIG_SYS_SPD_BUS_NUM 0 |
| #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ |
| #define SPD_EEPROM_ADDRESS1 0x51 |
| #define SPD_EEPROM_ADDRESS2 0x52 |
| #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 |
| #define CTRL_INTLV_PREFERED cacheline |
| |
| /* |
| * IFC Definitions |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xe8000000 |
| #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) |
| #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| |
| /* NOR Flash Timing Params */ |
| #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 |
| |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1A) |\ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0x0E) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CONFIG_SYS_NOR_FTIM3 0x0 |
| |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } |
| |
| /* CPLD on IFC */ |
| #define CONFIG_SYS_CPLD_BASE 0xffdf0000 |
| #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) |
| #define CONFIG_SYS_CSPR2_EXT (0xf) |
| #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) |
| #define CONFIG_SYS_CSOR2 0x0 |
| |
| /* CPLD Timing parameters for IFC CS2 */ |
| #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ |
| FTIM1_GPCM_TRAD(0x1f)) |
| #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ |
| FTIM2_GPCM_TCH(0x8) | \ |
| FTIM2_GPCM_TWP(0x1f)) |
| #define CONFIG_SYS_CS2_FTIM3 0x0 |
| |
| /* NAND Flash on IFC */ |
| #define CONFIG_NAND_FSL_IFC |
| #define CONFIG_SYS_NAND_BASE 0xff800000 |
| #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) |
| |
| #define CONFIG_SYS_NAND_CSPR_EXT (0xf) |
| #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) |
| |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ |
| | CSOR_NAND_PGS_2K /* Page Size = 2K */\ |
| | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ |
| | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ |
| |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ |
| FTIM0_NAND_TWP(0x18) | \ |
| FTIM0_NAND_TWCHT(0x07) | \ |
| FTIM0_NAND_TWH(0x0a)) |
| #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ |
| FTIM1_NAND_TWBE(0x39) | \ |
| FTIM1_NAND_TRR(0x0e) | \ |
| FTIM1_NAND_TRP(0x18)) |
| #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ |
| FTIM2_NAND_TREH(0x0a) | \ |
| FTIM2_NAND_TWHRE(0x1e)) |
| #define CONFIG_SYS_NAND_FTIM3 0x0 |
| |
| #define CONFIG_SYS_NAND_DDR_LAW 11 |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_CMD_NAND |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) |
| |
| #if defined(CONFIG_NAND) |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #else |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #endif |
| |
| #if defined(CONFIG_RAMBOOT_PBL) |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE |
| #else |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #endif |
| |
| #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ |
| #define CONFIG_MISC_INIT_R |
| #define CONFIG_HWCONFIG |
| |
| /* define to use L1 as initial stack */ |
| #define CONFIG_L1_INIT_RAM |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 |
| /* The assembler doesn't like typecast */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ |
| ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ |
| CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) |
| #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) |
| #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT |
| #define CONFIG_OF_BOARD_SETUP |
| #define CONFIG_OF_STDOUT_VIA_ALIAS |
| |
| /* new uImage format support */ |
| #define CONFIG_FIT |
| #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 |
| #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 |
| #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 |
| #define CONFIG_SYS_FSL_I2C_SPEED 100000 |
| #define CONFIG_SYS_FSL_I2C2_SPEED 100000 |
| #define CONFIG_SYS_FSL_I2C3_SPEED 100000 |
| #define CONFIG_SYS_FSL_I2C4_SPEED 100000 |
| #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ |
| #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ |
| #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| |
| |
| /* |
| * RapidIO |
| */ |
| #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull |
| #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 |
| #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull |
| #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ |
| /* |
| * for slave u-boot IMAGE instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ |
| #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull |
| /* |
| * for slave UCODE and ENV instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull |
| #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ |
| |
| /* slave core release by master*/ |
| #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 |
| #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ |
| |
| /* |
| * SRIO_PCIE_BOOT - SLAVE |
| */ |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 |
| #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ |
| (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) |
| #endif |
| |
| /* |
| * eSPI - Enhanced SPI |
| */ |
| #ifdef CONFIG_SPI_FLASH |
| #define CONFIG_FSL_ESPI |
| #define CONFIG_SPI_FLASH_STMICRO |
| #define CONFIG_SPI_FLASH_BAR |
| #define CONFIG_CMD_SF |
| #define CONFIG_SF_DEFAULT_SPEED 10000000 |
| #define CONFIG_SF_DEFAULT_MODE 0 |
| #endif |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| #define CONFIG_PCI /* Enable PCI/PCIE */ |
| #define CONFIG_PCIE1 /* PCIE controler 1 */ |
| #define CONFIG_PCIE2 /* PCIE controler 2 */ |
| #define CONFIG_PCIE3 /* PCIE controler 3 */ |
| #define CONFIG_PCIE4 /* PCIE controler 4 */ |
| #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ |
| #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ |
| /* controller 1, direct to uli, tgtid 3, Base address 20000 */ |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 2, Slot 2, tgtid 2, Base address 201000 */ |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 |
| #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 3, Slot 1, tgtid 1, Base address 202000 */ |
| #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 |
| #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull |
| #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 |
| #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull |
| #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 4, Base address 203000 */ |
| #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 |
| #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull |
| #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull |
| #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_INDIRECT_BRIDGE |
| #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ |
| #define CONFIG_NET_MULTI |
| #define CONFIG_E1000 |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| /* Qman/Bman */ |
| #ifndef CONFIG_NOBQFMAN |
| #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ |
| #define CONFIG_SYS_BMAN_NUM_PORTALS 18 |
| #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 |
| #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull |
| #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 |
| #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE |
| #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ |
| CONFIG_SYS_BMAN_CENA_SIZE) |
| #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 |
| #define CONFIG_SYS_QMAN_NUM_PORTALS 18 |
| #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 |
| #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull |
| #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 |
| #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE |
| #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ |
| CONFIG_SYS_QMAN_CENA_SIZE) |
| #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 |
| |
| #define CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_SYS_DPAA_PME |
| #define CONFIG_SYS_PMAN |
| #define CONFIG_SYS_DPAA_DCE |
| #define CONFIG_SYS_DPAA_RMAN /* RMan */ |
| #define CONFIG_SYS_INTERLAKEN |
| |
| /* Default address of microcode for the Linux Fman driver */ |
| #if defined(CONFIG_SPIFLASH) |
| /* |
| * env is stored at 0x100000, sector size is 0x10000, ucode is stored after |
| * env, so we got 0x110000. |
| */ |
| #define CONFIG_SYS_QE_FW_IN_SPIFLASH |
| #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH |
| #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 |
| #define CONFIG_CORTINA_FW_ADDR 0x120000 |
| |
| #elif defined(CONFIG_SDCARD) |
| /* |
| * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is |
| * about 1MB (2048 blocks), Env is stored after the image, and the env size is |
| * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. |
| */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_MMC |
| #define CONFIG_SYS_CORTINA_FW_IN_MMC |
| #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) |
| #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) |
| |
| #elif defined(CONFIG_NAND) |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NAND |
| #define CONFIG_SYS_CORTINA_FW_IN_NAND |
| #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) |
| /* |
| * Slave has no ucode locally, it can fetch this from remote. When implementing |
| * in two corenet boards, slave's ucode could be stored in master's memory |
| * space, the address can be mapped from slave TLB->slave LAW-> |
| * slave SRIO or PCIE outbound window->master inbound window-> |
| * master LAW->the ucode address in master's memory space. |
| */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE |
| #define CONFIG_SYS_CORTINA_FW_IN_REMOTE |
| #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 |
| #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 |
| #else |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NOR |
| #define CONFIG_SYS_CORTINA_FW_IN_NOR |
| #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 |
| #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 |
| #endif |
| #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 |
| #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) |
| #endif /* CONFIG_NOBQFMAN */ |
| |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_FMAN_ENET |
| #define CONFIG_PHYLIB_10G |
| #define CONFIG_PHY_CORTINA |
| #define CONFIG_PHY_AQ1202 |
| #define CONFIG_PHY_REALTEK |
| #define CONFIG_CORTINA_FW_LENGTH 0x40000 |
| #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ |
| #define RGMII_PHY2_ADDR 0x02 |
| #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ |
| #define CORTINA_PHY_ADDR2 0x0d |
| #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ |
| #define FM1_10GEC4_PHY_ADDR 0x01 |
| #endif |
| |
| |
| #ifdef CONFIG_FMAN_ENET |
| #define CONFIG_MII /* MII PHY management */ |
| #define CONFIG_ETHPRIME "FM1@DTSEC3" |
| #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ |
| #endif |
| |
| /* |
| * SATA |
| */ |
| #ifdef CONFIG_FSL_SATA_V2 |
| #define CONFIG_LIBATA |
| #define CONFIG_FSL_SATA |
| #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| #define CONFIG_SATA1 |
| #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR |
| #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA |
| #define CONFIG_SATA2 |
| #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR |
| #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA |
| #define CONFIG_LBA48 |
| #define CONFIG_CMD_SATA |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_CMD_EXT2 |
| #endif |
| |
| /* |
| * USB |
| */ |
| #ifdef CONFIG_USB_EHCI |
| #define CONFIG_CMD_USB |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_USB_EHCI_FSL |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_HAS_FSL_DR_USB |
| #endif |
| |
| /* |
| * SDHC |
| */ |
| #ifdef CONFIG_MMC |
| #define CONFIG_CMD_MMC |
| #define CONFIG_FSL_ESDHC |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT |
| #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_FAT |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| /* |
| * Dynamic MTD Partition support with mtdparts |
| */ |
| #ifndef CONFIG_SYS_NO_FLASH |
| #define CONFIG_MTD_DEVICE |
| #define CONFIG_MTD_PARTITIONS |
| #define CONFIG_CMD_MTDPARTS |
| #define CONFIG_FLASH_CFI_MTD |
| #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ |
| "spi0=spife110000.1" |
| #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ |
| "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ |
| "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ |
| "1m(uboot),5m(kernel),128k(dtb),-(user)" |
| #endif |
| |
| /* |
| * Environment |
| */ |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_ERRATA |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_ECHO |
| #define CONFIG_CMD_SETEXPR |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_BDI |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_NET |
| #endif |
| |
| /* Hash command with SHA acceleration supported in hardware */ |
| #ifdef CONFIG_FSL_CAAM |
| #define CONFIG_CMD_HASH |
| #define CONFIG_SHA_HW_ACCEL |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #ifdef CONFIG_CMD_KGDB |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| #ifdef CONFIG_CMD_KGDB |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_BOOTFILE "uImage" |
| #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ |
| |
| /* default location for tftp and bootm */ |
| #define CONFIG_LOADADDR 1000000 |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ |
| #define __USB_PHY_TYPE utmi |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:" \ |
| "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ |
| "bank_intlv=auto;" \ |
| "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ |
| "netdev=eth0\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot && " \ |
| "protect off $ubootaddr +$filesize && " \ |
| "erase $ubootaddr +$filesize && " \ |
| "cp.b $loadaddr $ubootaddr $filesize && " \ |
| "protect on $ubootaddr +$filesize && " \ |
| "cmp.b $loadaddr $ubootaddr $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ |
| "fdtaddr=c00000\0" \ |
| "fdtfile=t2080rdb/t2080rdb.dtb\0" \ |
| "bdev=sda3\0" |
| |
| /* |
| * For emulation this causes u-boot to jump to the start of the |
| * proof point app code automatically |
| */ |
| #define CONFIG_PROOF_POINTS \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "cpu 1 release 0x29000000 - - -;" \ |
| "cpu 2 release 0x29000000 - - -;" \ |
| "cpu 3 release 0x29000000 - - -;" \ |
| "cpu 4 release 0x29000000 - - -;" \ |
| "cpu 5 release 0x29000000 - - -;" \ |
| "cpu 6 release 0x29000000 - - -;" \ |
| "cpu 7 release 0x29000000 - - -;" \ |
| "go 0x29000000" |
| |
| #define CONFIG_HVBOOT \ |
| "setenv bootargs config-addr=0x60000000; " \ |
| "bootm 0x01000000 - 0x00f00000" |
| |
| #define CONFIG_ALU \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "cpu 1 release 0x01000000 - - -;" \ |
| "cpu 2 release 0x01000000 - - -;" \ |
| "cpu 3 release 0x01000000 - - -;" \ |
| "cpu 4 release 0x01000000 - - -;" \ |
| "cpu 5 release 0x01000000 - - -;" \ |
| "cpu 6 release 0x01000000 - - -;" \ |
| "cpu 7 release 0x01000000 - - -;" \ |
| "go 0x01000000" |
| |
| #define CONFIG_LINUX \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "setenv ramdiskaddr 0x02000000;" \ |
| "setenv fdtaddr 0x00c00000;" \ |
| "setenv loadaddr 0x1000000;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_HDBOOT \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_LINUX |
| |
| #ifdef CONFIG_SECURE_BOOT |
| #include <asm/fsl_secure_boot.h> |
| #define CONFIG_CMD_BLOB |
| #undef CONFIG_CMD_USB |
| #endif |
| |
| #endif /* __T2080RDB_H */ |