blob: 64461f6a90ebd87bbbb9ba452fa664d9c6257035 [file] [log] [blame]
/*
* (C) Copyright 2003-2006
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
#define CONFIG_UC101 1 /* UC101 board */
#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CONFIG_BOARD_EARLY_INIT_R
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/* Partitions */
#define CONFIG_DOS_PARTITION
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DISPLAY
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_CMD_DTT
#define CONFIG_CMD_IDE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_NFS
#define CONFIG_CMD_MII
#define CONFIG_CMD_SNTP
#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
#if (TEXT_BASE == 0xFFF00000) /* Boot low */
# define CFG_LOWBOOT 1
#endif
/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addwdt=setenv bootargs ${bootargs} wdt=off" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
"bootm ${kernel_addr}\0" \
"net_nfs=tftp 300000 ${bootfile};run nfsargs addip addwdt;bootm\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
""
#define CONFIG_BOOTCOMMAND "run net_nfs"
#define CONFIG_MISC_INIT_R 1
/*
* IPB Bus clocking configuration.
*/
#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CFG_I2C_SPEED 100000 /* 100 kHz */
#define CFG_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CFG_I2C_EEPROM_ADDR 0x58
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_BITS 4
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
/* for LM81 */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
/*
* RTC configuration
*/
#define CONFIG_RTC_PCF8563
#define CFG_I2C_RTC_ADDR 0x51
/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM81 1 /* ON Semi's LM75 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
#define CFG_DTT_MAX_TEMP 70
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
/*
* Flash configuration
*/
#define CFG_FLASH_BASE 0xFF800000
#define CFG_FLASH_SIZE 0x00800000 /* 8 MByte */
#define CFG_MAX_FLASH_SECT 140 /* max num of sects on one chip */
#define CFG_ENV_ADDR (TEXT_BASE+0x40000) /* second sector */
#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks
(= chip selects) */
#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#define CFG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#define CFG_FLASH_CFI_AMD_RESET
/*
* Environment settings
*/
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_SIZE 0x4000
#define CFG_ENV_SECT_SIZE 0x10000
#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*
* Memory map
*/
#define CFG_MBAR 0xF0000000
#define CFG_DEFAULT_MBAR 0x80000000
#define CFG_SDRAM_BASE 0x00000000
#define CFG_SRAM_BASE 0x80100000 /* CS 1 */
#define CFG_DISPLAY_BASE 0x80600000 /* CS 3 */
#define CFG_IB_MASTER 0xc0510000 /* CS 6 */
#define CFG_IB_EPLD 0xc0500000 /* CS 7 */
/* Settings for XLB = 132 MHz */
#define SDRAM_DDR 1
#define SDRAM_MODE 0x018D0000
#define SDRAM_EMODE 0x40090000
#define SDRAM_CONTROL 0x714f0f00
#define SDRAM_CONFIG1 0x73722930
#define SDRAM_CONFIG2 0x47770000
#define SDRAM_TAPDELAY 0x10000000
/* SRAM */
#define SRAM_BASE CFG_SRAM_BASE /* SRAM base address */
#define SRAM_LEN 0x1fffff
#define SRAM_END (SRAM_BASE + SRAM_LEN)
/* Use ON-Chip SRAM until RAM will be available */
#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
#ifdef CONFIG_POST
/* preserve space for the post_word at end of on-chip SRAM */
#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE
#else
#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE
#endif
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_BASE TEXT_BASE
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
# define CFG_RAMBOOT 1
#endif
#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#define CFG_MALLOC_LEN (512 << 10) /* Reserve 128 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_PHY_ADDR 0x00
#define CONFIG_MII 1
/*
* GPIO configuration
*/
#define CFG_GPS_PORT_CONFIG 0x4d558044
/*use Hardware WDT */
#define CONFIG_HW_WATCHDOG
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
/* Enable an alternate, more extensive memory test */
#define CFG_ALT_MEMTEST
#define CFG_MEMTEST_START 0x00300000 /* memtest works on */
#define CFG_MEMTEST_END 0x00f00000 /* 3 ... 15 MB in DRAM */
#define CFG_LOAD_ADDR 0x300000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
* which is normally part of the default commands (CFV_CMD_DFL)
*/
#define CONFIG_LOOPW
/*
* Various low-level settings
*/
#if defined(CONFIG_MPC5200)
#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
#define CFG_HID0_FINAL HID0_ICE
#else
#define CFG_HID0_INIT 0
#define CFG_HID0_FINAL 0
#endif
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
#define CFG_BOOTCS_CFG 0x00045D00
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
/* 8Mbit SRAM @0x80100000 */
#define CFG_CS1_START CFG_SRAM_BASE
#define CFG_CS1_SIZE 0x00100000
#define CFG_CS1_CFG 0x21D00
/* Display H1, Status Inputs, EPLD @0x80600000 8 Bit */
#define CFG_CS3_START CFG_DISPLAY_BASE
#define CFG_CS3_SIZE 0x00000100
#define CFG_CS3_CFG 0x00081802
/* Interbus Master 16 Bit */
#define CFG_CS6_START CFG_IB_MASTER
#define CFG_CS6_SIZE 0x00010000
#define CFG_CS6_CFG 0x00FF3500
/* Interbus EPLD 8 Bit */
#define CFG_CS7_START CFG_IB_EPLD
#define CFG_CS7_SIZE 0x00010000
#define CFG_CS7_CFG 0x00081800
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333333
/*-----------------------------------------------------------------------
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
#define CONFIG_IDE_PREINIT 1
/* #define CONFIG_IDE_RESET 1 beispile siehe tqm5200.c */
#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
#define CFG_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
#define CFG_ATA_STRIDE 4
#define CONFIG_ATAPI 1
/*---------------------------------------------------------------------*/
/* Display addresses */
/*---------------------------------------------------------------------*/
#define CFG_DISP_CHR_RAM (CFG_DISPLAY_BASE + 0x38)
#define CFG_DISP_CWORD (CFG_DISPLAY_BASE + 0x30)
#endif /* __CONFIG_H */