include/configs/MPC8315ERDB.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
  *
  * Dave Liu <daveliu@freescale.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_DISPLAY_BOARDINFO

 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xFE000000
 #endif

 #ifndef CONFIG_SYS_MONITOR_BASE
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #endif

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
 #define CONFIG_MPC831x		1 /* MPC831x CPU family */
 #define CONFIG_MPC8315		1 /* MPC8315 CPU specific */
 #define CONFIG_MPC8315ERDB	1 /* MPC8315ERDB board specific */

 /*
  * System Clock Setup
  */
 #define CONFIG_83XX_CLKIN	66666667 /* in Hz */
 #define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN

 /*
  * Hardware Reset Configuration Word
  * if CLKIN is 66.66MHz, then
  * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
  */
 #define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
 	HRCWL_SVCOD_DIV_2 |\
 	HRCWL_CSB_TO_CLKIN_2X1 |\
 	HRCWL_CORE_TO_CSB_3X1)
 #define CONFIG_SYS_HRCW_HIGH_BASE (\
 	HRCWH_PCI_HOST |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
 	HRCWH_CORE_ENABLE |\
 	HRCWH_BOOTSEQ_DISABLE |\
 	HRCWH_SW_WATCHDOG_DISABLE |\
 	HRCWH_TSEC1M_IN_RGMII |\
 	HRCWH_TSEC2M_IN_RGMII |\
 	HRCWH_BIG_ENDIAN |\
 	HRCWH_LALE_NORMAL)

 #ifdef CONFIG_NAND_SPL
 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
 		       HRCWH_FROM_0XFFF00100 |\
 		       HRCWH_ROM_LOC_NAND_SP_8BIT |\
 		       HRCWH_RL_EXT_NAND)
 #else
 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
 		       HRCWH_FROM_0X00000100 |\
 		       HRCWH_ROM_LOC_LOCAL_16BIT |\
 		       HRCWH_RL_EXT_LEGACY)
 #endif

 /*
  * System IO Config
  */
 #define CONFIG_SYS_SICRH		0x00000000
 #define CONFIG_SYS_SICRL		0x00000000 /* 3.3V, no delay */

 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
 #define CONFIG_HWCONFIG

 /*
  * IMMR new address
  */
 #define CONFIG_SYS_IMMR		0xE0000000

 /*
  * Arbiter Setup
  */
 #define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
 #define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
 #define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */

 /*
  * DDR Setup
  */
 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
 				| DDRCDR_PZ_LOZ \
 				| DDRCDR_NZ_LOZ \
 				| DDRCDR_ODT \
 				| DDRCDR_Q_DRN)
 				/* 0x7b880001 */
 /*
  * Manually set up DDR parameters
  * consist of two chips HY5PS12621BFP-C4 from HYNIX
  */
 #define CONFIG_SYS_DDR_SIZE		128 /* MB */
 #define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
 #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
 				| CSCONFIG_ODT_RD_NEVER \
 				| CSCONFIG_ODT_WR_ONLY_CURRENT \
 				| CSCONFIG_ROW_BIT_13 \
 				| CSCONFIG_COL_BIT_10)
 				/* 0x80010102 */
 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
 #define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
 				| (0 << TIMING_CFG0_WRT_SHIFT) \
 				| (0 << TIMING_CFG0_RRT_SHIFT) \
 				| (0 << TIMING_CFG0_WWT_SHIFT) \
 				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 				/* 0x00220802 */
 #define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
 				| (6 << TIMING_CFG1_REFREC_SHIFT) \
 				| (2 << TIMING_CFG1_WRREC_SHIFT) \
 				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 				| (2 << TIMING_CFG1_WRTORD_SHIFT))
 				/* 0x27256222 */
 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
 				| (4 << TIMING_CFG2_CPO_SHIFT) \
 				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 				/* 0x121048c5 */
 #define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
 				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 				/* 0x03600100 */
 #define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_DBW_32)
 				/* 0x43080000 */
 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
 				| (0x0232 << SDRAM_MODE_SD_SHIFT))
 				/* ODT 150ohm CL=3, AL=1 on SDRAM */
 #define CONFIG_SYS_DDR_MODE2	0x00000000

 /*
  * Memory test
  */
 #undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START	0x00040000 /* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00140000

 /*
  * The reserved memory
  */
 #define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */

 /*
  * Initial RAM Base Address Setup
  */
 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

 /*
  * Local Bus Configuration & Clock Setup
  */
 #define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
 #define CONFIG_SYS_LBC_LBCR		0x00040000
 #define CONFIG_FSL_ELBC		1

 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
 #define CONFIG_FLASH_CFI_DRIVER	/* use the CFI driver */
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT

 #define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
 #define CONFIG_SYS_FLASH_SIZE		8	/* FLASH size is 8M */
 #define CONFIG_SYS_FLASH_PROTECTION	1	/* Use h/w Flash protection. */

 					/* Window base at flash base */
 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)

 #define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE \
 					| BR_PS_16	/* 16 bit port */ \
 					| BR_MS_GPCM	/* MSEL = GPCM */ \
 					| BR_V)		/* valid */
 #define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 					| OR_UPM_XAM \
 					| OR_GPCM_CSNT \
 					| OR_GPCM_ACS_DIV2 \
 					| OR_GPCM_XACS \
 					| OR_GPCM_SCY_15 \
 					| OR_GPCM_TRLX_SET \
 					| OR_GPCM_EHTR_SET \
 					| OR_GPCM_EAD)

 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
 /* 127 64KB sectors and 8 8KB top sectors per device */
 #define CONFIG_SYS_MAX_FLASH_SECT	135

 #undef CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */

 /*
  * NAND Flash on the Local Bus
  */

 #ifdef CONFIG_NAND_SPL
 #define CONFIG_SYS_NAND_BASE		0xFFF00000
 #else
 #define CONFIG_SYS_NAND_BASE		0xE0600000
 #endif

 #define CONFIG_MTD_DEVICE
 #define CONFIG_MTD_PARTITION
 #define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT			"nand0=e0600000.flash"
 #define MTDPARTS_DEFAULT		\
 	"mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)"

 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_CMD_NAND			1
 #define CONFIG_NAND_FSL_ELBC		1
 #define CONFIG_SYS_NAND_BLOCK_SIZE	16384
 #define CONFIG_SYS_NAND_WINDOW_SIZE    (32 * 1024)     /* 0x00008000 */

 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000

 #define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE \
 				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
 				| BR_PS_8		/* 8 bit port */ \
 				| BR_MS_FCM		/* MSEL = FCM */ \
 				| BR_V)			/* valid */
 #define CONFIG_SYS_NAND_OR_PRELIM	\
 				(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
 				| OR_FCM_CSCT \
 				| OR_FCM_CST \
 				| OR_FCM_CHT \
 				| OR_FCM_SCY_1 \
 				| OR_FCM_TRLX \
 				| OR_FCM_EHTR)
 				/* 0xFFFF8396 */

 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM

 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
 #define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)

 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM

 #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
 	!defined(CONFIG_NAND_SPL)
 #define CONFIG_SYS_RAMBOOT
 #else
 #undef CONFIG_SYS_RAMBOOT
 #endif

 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)

 #define CONFIG_SYS_BAUDRATE_TABLE  \
 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)

 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER

 /* Pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 #define CONFIG_OF_STDOUT_VIA_ALIAS	1

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x51} }

 /*
  * Board info - revision and where boot from
  */
 #define CONFIG_SYS_I2C_PCF8574A_ADDR	0x39

 /*
  * Config on-board RTC
  */
 #define CONFIG_RTC_DS1337	/* ds1339 on board, use ds1337 rtc via i2c */
 #define CONFIG_SYS_I2C_RTC_ADDR	0x68 /* at address 0x68 */

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI_MEM_BASE		0x80000000
 #define CONFIG_SYS_PCI_MEM_PHYS		CONFIG_SYS_PCI_MEM_BASE
 #define CONFIG_SYS_PCI_MEM_SIZE		0x10000000 /* 256M */
 #define CONFIG_SYS_PCI_MMIO_BASE	0x90000000
 #define CONFIG_SYS_PCI_MMIO_PHYS	CONFIG_SYS_PCI_MMIO_BASE
 #define CONFIG_SYS_PCI_MMIO_SIZE	0x10000000 /* 256M */
 #define CONFIG_SYS_PCI_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI_IO_PHYS		0xE0300000
 #define CONFIG_SYS_PCI_IO_SIZE		0x100000 /* 1M */

 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE
 #define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
 #define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000

 #define CONFIG_SYS_PCIE1_BASE		0xA0000000
 #define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
 #define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
 #define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
 #define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000

 #define CONFIG_SYS_PCIE2_BASE		0xC0000000
 #define CONFIG_SYS_PCIE2_MEM_BASE	0xC0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xC0000000
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
 #define CONFIG_SYS_PCIE2_CFG_BASE	0xD0000000
 #define CONFIG_SYS_PCIE2_CFG_SIZE	0x01000000
 #define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xD1000000
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000

 #define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_PCIE

 #define CONFIG_PCI_PNP		/* do pci plug-and-play */

 #define CONFIG_EEPRO100
 #undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */

 #define CONFIG_HAS_FSL_DR_USB
 #define CONFIG_SYS_SCCR_USBDRCM		3

 #define CONFIG_CMD_USB
 #define CONFIG_USB_STORAGE
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_USB_PHY_TYPE	"utmi"
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET

 /*
  * TSEC
  */
 #define CONFIG_TSEC_ENET	/* TSEC ethernet support */
 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

 /*
  * TSEC ethernet configuration
  */
 #define CONFIG_MII		1 /* MII PHY management */
 #define CONFIG_TSEC1		1
 #define CONFIG_TSEC1_NAME	"eTSEC0"
 #define CONFIG_TSEC2		1
 #define CONFIG_TSEC2_NAME	"eTSEC1"
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define TSEC1_FLAGS		TSEC_GIGABIT
 #define TSEC2_FLAGS		TSEC_GIGABIT

 /* Options are: eTSEC[0-1] */
 #define CONFIG_ETHPRIME		"eTSEC1"

 /*
  * SATA
  */
 #define CONFIG_LIBATA
 #define CONFIG_FSL_SATA

 #define CONFIG_SYS_SATA_MAX_DEVICE	2
 #define CONFIG_SATA1
 #define CONFIG_SYS_SATA1_OFFSET	0x18000
 #define CONFIG_SYS_SATA1	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
 #define CONFIG_SYS_SATA1_FLAGS	FLAGS_DMA
 #define CONFIG_SATA2
 #define CONFIG_SYS_SATA2_OFFSET	0x19000
 #define CONFIG_SYS_SATA2	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
 #define CONFIG_SYS_SATA2_FLAGS	FLAGS_DMA

 #ifdef CONFIG_FSL_SATA
 #define CONFIG_LBA48
 #define CONFIG_CMD_SATA
 #define CONFIG_DOS_PARTITION
 #define CONFIG_CMD_EXT2
 #endif

 /*
  * Environment
  */
 #if !defined(CONFIG_SYS_RAMBOOT)
 	#define CONFIG_ENV_IS_IN_FLASH	1
 	#define CONFIG_ENV_ADDR		\
 			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 	#define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K(one sector) for env */
 	#define CONFIG_ENV_SIZE		0x2000
 #else
 	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */
 	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 	#define CONFIG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 /*
  * Command line configuration.
  */
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_PCI

 #define CONFIG_CMDLINE_EDITING	1	/* add command line history */
 #define CONFIG_AUTO_COMPLETE		/* add autocompletion support */

 #undef CONFIG_WATCHDOG		/* watchdog disabled */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */

 #if defined(CONFIG_CMD_KGDB)
 	#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
 #else
 	#define CONFIG_SYS_CBSIZE	256 /* Console I/O Buffer Size */
 #endif

 				/* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
 				/* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */

 /*
  * Core HID Setup
  */
 #define CONFIG_SYS_HID0_INIT	0x000000000
 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
 				 HID0_ENABLE_INSTRUCTION_CACHE | \
 				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 #define CONFIG_SYS_HID2		HID2_HBE

 /*
  * MMU Setup
  */
 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 /* DDR: cache cacheable */
 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
 				| BATL_PP_RW \
 				| BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
 				| BATU_BL_128M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U

 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR \
 				| BATU_BL_8M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U

 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE \
 				| BATL_PP_RW \
 				| BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE \
 				| BATU_BL_32M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U

 /* Stack in dcache: cacheable, no memory coherence */
 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR \
 				| BATU_BL_128K \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

 /* PCI MEM space: cacheable */
 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI_MEM_PHYS \
 				| BATL_PP_RW \
 				| BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI_MEM_PHYS \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
 #define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U

 /* PCI MMIO space: cache-inhibit and guarded */
 #define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI_MMIO_PHYS \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI_MMIO_PHYS \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U

 #define CONFIG_SYS_IBAT6L	0
 #define CONFIG_SYS_IBAT6U	0
 #define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
 #define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U

 #define CONFIG_SYS_IBAT7L	0
 #define CONFIG_SYS_IBAT7U	0
 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */

 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #endif

 #define CONFIG_BAUDRATE 115200

 #define CONFIG_LOADADDR 800000	/* default location for tftp and bootm */

 #define CONFIG_BOOTDELAY 6	/* -1 disables auto-boot */
 #undef CONFIG_BOOTARGS		/* the boot command will set bootargs */

 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"consoledev=ttyS0\0"						\
 	"ramdiskaddr=1000000\0"						\
 	"ramdiskfile=ramfs.83xx\0"					\
 	"fdtaddr=780000\0"						\
 	"fdtfile=mpc8315erdb.dtb\0"					\
 	"usb_phy_type=utmi\0"						\
 	""

 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs root=/dev/nfs rw "				\
 		"nfsroot=$serverip:$rootpath "				\
 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
 							"$netdev:off "	\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"setenv bootargs root=/dev/ram rw "				\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"


 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND

 #endif	/* __CONFIG_H */
	/*
	* Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
	*
	* Dave Liu <daveliu@freescale.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_DISPLAY_BOARDINFO

	#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
	#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
	#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
	#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
	#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xFE000000
	#endif

	#ifndef CONFIG_SYS_MONITOR_BASE
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1 /* E300 family */
	#define CONFIG_MPC831x 1 /* MPC831x CPU family */
	#define CONFIG_MPC8315 1 /* MPC8315 CPU specific */
	#define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */

	/*
	* System Clock Setup
	*/
	#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
	#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN

	/*
	* Hardware Reset Configuration Word
	* if CLKIN is 66.66MHz, then
	* CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
	*/
	#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_2X1 \|\
	HRCWL_SVCOD_DIV_2 \|\
	HRCWL_CSB_TO_CLKIN_2X1 \|\
	HRCWL_CORE_TO_CSB_3X1)
	#define CONFIG_SYS_HRCW_HIGH_BASE (\
	HRCWH_PCI_HOST \|\
	HRCWH_PCI1_ARBITER_ENABLE \|\
	HRCWH_CORE_ENABLE \|\
	HRCWH_BOOTSEQ_DISABLE \|\
	HRCWH_SW_WATCHDOG_DISABLE \|\
	HRCWH_TSEC1M_IN_RGMII \|\
	HRCWH_TSEC2M_IN_RGMII \|\
	HRCWH_BIG_ENDIAN \|\
	HRCWH_LALE_NORMAL)

	#ifdef CONFIG_NAND_SPL
	#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \|\
	HRCWH_FROM_0XFFF00100 \|\
	HRCWH_ROM_LOC_NAND_SP_8BIT \|\
	HRCWH_RL_EXT_NAND)
	#else
	#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \|\
	HRCWH_FROM_0X00000100 \|\
	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	HRCWH_RL_EXT_LEGACY)
	#endif

	/*
	* System IO Config
	*/
	#define CONFIG_SYS_SICRH 0x00000000
	#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */

	#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
	#define CONFIG_HWCONFIG

	/*
	* IMMR new address
	*/
	#define CONFIG_SYS_IMMR 0xE0000000

	/*
	* Arbiter Setup
	*/
	#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
	#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
	#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */

	/*
	* DDR Setup
	*/
	#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
	#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
	\| DDRCDR_PZ_LOZ \
	\| DDRCDR_NZ_LOZ \
	\| DDRCDR_ODT \
	\| DDRCDR_Q_DRN)
	/* 0x7b880001 */
	/*
	* Manually set up DDR parameters
	* consist of two chips HY5PS12621BFP-C4 from HYNIX
	*/
	#define CONFIG_SYS_DDR_SIZE 128 /* MB */
	#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
	#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
	\| CSCONFIG_ODT_RD_NEVER \
	\| CSCONFIG_ODT_WR_ONLY_CURRENT \
	\| CSCONFIG_ROW_BIT_13 \
	\| CSCONFIG_COL_BIT_10)
	/* 0x80010102 */
	#define CONFIG_SYS_DDR_TIMING_3 0x00000000
	#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
	\| (0 << TIMING_CFG0_WRT_SHIFT) \
	\| (0 << TIMING_CFG0_RRT_SHIFT) \
	\| (0 << TIMING_CFG0_WWT_SHIFT) \
	\| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
	\| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
	\| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
	\| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
	/* 0x00220802 */
	#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
	\| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
	\| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
	\| (5 << TIMING_CFG1_CASLAT_SHIFT) \
	\| (6 << TIMING_CFG1_REFREC_SHIFT) \
	\| (2 << TIMING_CFG1_WRREC_SHIFT) \
	\| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
	\| (2 << TIMING_CFG1_WRTORD_SHIFT))
	/* 0x27256222 */
	#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
	\| (4 << TIMING_CFG2_CPO_SHIFT) \
	\| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
	\| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
	\| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
	\| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
	\| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
	/* 0x121048c5 */
	#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
	\| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
	/* 0x03600100 */
	#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
	\| SDRAM_CFG_SDRAM_TYPE_DDR2 \
	\| SDRAM_CFG_DBW_32)
	/* 0x43080000 */
	#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
	#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
	\| (0x0232 << SDRAM_MODE_SD_SHIFT))
	/* ODT 150ohm CL=3, AL=1 on SDRAM */
	#define CONFIG_SYS_DDR_MODE2 0x00000000

	/*
	* Memory test
	*/
	#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
	#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */
	#define CONFIG_SYS_MEMTEST_END 0x00140000

	/*
	* The reserved memory
	*/
	#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */

	/*
	* Initial RAM Base Address Setup
	*/
	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

	/*
	* Local Bus Configuration & Clock Setup
	*/
	#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
	#define CONFIG_SYS_LBC_LBCR 0x00040000
	#define CONFIG_FSL_ELBC 1

	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
	#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT

	#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
	#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
	#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */

	/* Window base at flash base */
	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_8MB)

	#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \
	\| BR_PS_16 /* 16 bit port */ \
	\| BR_MS_GPCM /* MSEL = GPCM */ \
	\| BR_V) /* valid */
	#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
	\| OR_UPM_XAM \
	\| OR_GPCM_CSNT \
	\| OR_GPCM_ACS_DIV2 \
	\| OR_GPCM_XACS \
	\| OR_GPCM_SCY_15 \
	\| OR_GPCM_TRLX_SET \
	\| OR_GPCM_EHTR_SET \
	\| OR_GPCM_EAD)

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	/* 127 64KB sectors and 8 8KB top sectors per device */
	#define CONFIG_SYS_MAX_FLASH_SECT 135

	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	/*
	* NAND Flash on the Local Bus
	*/

	#ifdef CONFIG_NAND_SPL
	#define CONFIG_SYS_NAND_BASE 0xFFF00000
	#else
	#define CONFIG_SYS_NAND_BASE 0xE0600000
	#endif

	#define CONFIG_MTD_DEVICE
	#define CONFIG_MTD_PARTITION
	#define CONFIG_CMD_MTDPARTS
	#define MTDIDS_DEFAULT "nand0=e0600000.flash"
	#define MTDPARTS_DEFAULT \
	"mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)"

	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_CMD_NAND 1
	#define CONFIG_NAND_FSL_ELBC 1
	#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
	#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */

	#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
	#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
	#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
	#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
	#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000

	#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
	\| BR_DECC_CHK_GEN /* Use HW ECC */ \
	\| BR_PS_8 /* 8 bit port */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V) /* valid */
	#define CONFIG_SYS_NAND_OR_PRELIM \
	(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)
	/* 0xFFFF8396 */

	#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
	#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
	#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM

	#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
	#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN \| LBLAWAR_32KB)

	#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
	#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM

	#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
	!defined(CONFIG_NAND_SPL)
	#define CONFIG_SYS_RAMBOOT
	#else
	#undef CONFIG_SYS_RAMBOOT
	#endif

	/*
	* Serial Port
	*/
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

	/* Use the HUSH parser */
	#define CONFIG_SYS_HUSH_PARSER

	/* Pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1
	#define CONFIG_OF_STDOUT_VIA_ALIAS 1

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }

	/*
	* Board info - revision and where boot from
	*/
	#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39

	/*
	* Config on-board RTC
	*/
	#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
	#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
	#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
	#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
	#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
	#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */

	#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
	#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
	#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000

	#define CONFIG_SYS_PCIE1_BASE 0xA0000000
	#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
	#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
	#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
	#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000

	#define CONFIG_SYS_PCIE2_BASE 0xC0000000
	#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000
	#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
	#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000
	#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000
	#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000
	#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000

	#define CONFIG_PCI
	#define CONFIG_PCI_INDIRECT_BRIDGE
	#define CONFIG_PCIE

	#define CONFIG_PCI_PNP /* do pci plug-and-play */

	#define CONFIG_EEPRO100
	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */

	#define CONFIG_HAS_FSL_DR_USB
	#define CONFIG_SYS_SCCR_USBDRCM 3

	#define CONFIG_CMD_USB
	#define CONFIG_USB_STORAGE
	#define CONFIG_USB_EHCI
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_USB_PHY_TYPE "utmi"
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET

	/*
	* TSEC
	*/
	#define CONFIG_TSEC_ENET /* TSEC ethernet support */
	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
	#define CONFIG_SYS_TSEC2_OFFSET 0x25000
	#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

	/*
	* TSEC ethernet configuration
	*/
	#define CONFIG_MII 1 /* MII PHY management */
	#define CONFIG_TSEC1 1
	#define CONFIG_TSEC1_NAME "eTSEC0"
	#define CONFIG_TSEC2 1
	#define CONFIG_TSEC2_NAME "eTSEC1"
	#define TSEC1_PHY_ADDR 0
	#define TSEC2_PHY_ADDR 1
	#define TSEC1_PHYIDX 0
	#define TSEC2_PHYIDX 0
	#define TSEC1_FLAGS TSEC_GIGABIT
	#define TSEC2_FLAGS TSEC_GIGABIT

	/* Options are: eTSEC[0-1] */
	#define CONFIG_ETHPRIME "eTSEC1"

	/*
	* SATA
	*/
	#define CONFIG_LIBATA
	#define CONFIG_FSL_SATA

	#define CONFIG_SYS_SATA_MAX_DEVICE 2
	#define CONFIG_SATA1
	#define CONFIG_SYS_SATA1_OFFSET 0x18000
	#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
	#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
	#define CONFIG_SATA2
	#define CONFIG_SYS_SATA2_OFFSET 0x19000
	#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
	#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA

	#ifdef CONFIG_FSL_SATA
	#define CONFIG_LBA48
	#define CONFIG_CMD_SATA
	#define CONFIG_DOS_PARTITION
	#define CONFIG_CMD_EXT2
	#endif

	/*
	* Environment
	*/
	#if !defined(CONFIG_SYS_RAMBOOT)
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_ADDR \
	(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
	#define CONFIG_ENV_SIZE 0x2000
	#else
	#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
	#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	/*
	* Command line configuration.
	*/
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_PCI

	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif

	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 256 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */

	/*
	* Core HID Setup
	*/
	#define CONFIG_SYS_HID0_INIT 0x000000000
	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \| \
	HID0_ENABLE_INSTRUCTION_CACHE \| \
	HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
	#define CONFIG_SYS_HID2 HID2_HBE

	/*
	* MMU Setup
	*/
	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/* DDR: cache cacheable */
	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
	\| BATL_PP_RW \
	\| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
	\| BATU_BL_128M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U

	/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
	\| BATU_BL_8M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U

	/* FLASH: icache cacheable, but dcache-inhibit and guarded */
	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \
	\| BATL_PP_RW \
	\| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \
	\| BATU_BL_32M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U

	/* Stack in dcache: cacheable, no memory coherence */
	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_RW)
	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR \
	\| BATU_BL_128K \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U

	/* PCI MEM space: cacheable */
	#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI_MEM_PHYS \
	\| BATL_PP_RW \
	\| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI_MEM_PHYS \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U

	/* PCI MMIO space: cache-inhibit and guarded */
	#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI_MMIO_PHYS \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI_MMIO_PHYS \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U

	#define CONFIG_SYS_IBAT6L 0
	#define CONFIG_SYS_IBAT6U 0
	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U

	#define CONFIG_SYS_IBAT7L 0
	#define CONFIG_SYS_IBAT7U 0
	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/

	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_TSEC_ENET)
	#define CONFIG_HAS_ETH0
	#define CONFIG_HAS_ETH1
	#endif

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */

	#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
	#undef CONFIG_BOOTARGS /* the boot command will set bootargs */

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=1000000\0" \
	"ramdiskfile=ramfs.83xx\0" \
	"fdtaddr=780000\0" \
	"fdtfile=mpc8315erdb.dtb\0" \
	"usb_phy_type=utmi\0" \
	""

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
	"$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"


	#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND

	#endif /* __CONFIG_H */