include/configs/socfpga_vining_fpga.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) 2015 Marek Vasut <marex@denx.de>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
 #define __CONFIG_SAMTEC_VINING_FPGA_H__

 #include <asm/arch/base_addr_ac5.h>

 /* U-Boot Commands */
 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_DOS_PARTITION
 #define CONFIG_FAT_WRITE
 #define CONFIG_HW_WATCHDOG

 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_LED

 /* Memory configurations */
 #define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on VINING_FPGA */

 /* Booting Linux */
 #define CONFIG_BOOTFILE		"openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
 #define CONFIG_BOOTARGS		"console=ttyS0," __stringify(CONFIG_BAUDRATE)
 #define CONFIG_BOOTCOMMAND	"run selboot"
 #define CONFIG_LOADADDR		0x01000000
 #define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR

 /* I2C EEPROM */
 #ifdef CONFIG_CMD_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_I2C_EEPROM_BUS		0
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
 #endif

 /*
  * Status LEDs:
  *   0 ... Top Green
  *   1 ... Top Red
  *   2 ... Bottom Green
  *   3 ... Bottom Red
  */
 #define CONFIG_STATUS_LED
 #define CONFIG_GPIO_LED
 #define CONFIG_BOARD_SPECIFIC_LED
 #define STATUS_LED_BIT		48
 #define STATUS_LED_STATE	STATUS_LED_OFF
 #define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 2)
 #define STATUS_LED_BIT1		53
 #define STATUS_LED_STATE1	STATUS_LED_OFF
 #define STATUS_LED_PERIOD1	(CONFIG_SYS_HZ / 2)
 #define STATUS_LED_BIT2		54
 #define STATUS_LED_STATE2	STATUS_LED_OFF
 #define STATUS_LED_PERIOD2	(CONFIG_SYS_HZ / 2)
 #define STATUS_LED_BIT3		65
 #define STATUS_LED_STATE3	STATUS_LED_OFF
 #define STATUS_LED_PERIOD3	(CONFIG_SYS_HZ / 2)

 /* Ethernet on SoC (EMAC) */
 #if defined(CONFIG_CMD_NET)
 #define CONFIG_BOOTP_SEND_HOSTNAME
 /* PHY */
 #define CONFIG_PHY_MICREL
 #define CONFIG_PHY_MICREL_KSZ9021
 #endif

 /* Extra Environment */
 #define CONFIG_HOSTNAME			socfpga_vining_fpga

 /*
  * Active LOW GPIO buttons:
  * A: GPIO 77 ... the button between USB B and ethernet
  * B: GPIO 78 ... the button between USB A ports
  *
  * The logic:
  *  if button B is not pressed, boot normal Linux system immediatelly
  *  if button B is pressed, wait $bootdelay and boot recovery system
  */
 #define CONFIG_PREBOOT						\
 	"setenv hostname vining-${unit_serial} ; "		\
 	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; "	\
 	"if gpio input 78 ; then "			\
 		"setenv bootdelay 10 ; "		\
 		"setenv boottype rcvr ; "		\
 	"else "						\
 		"setenv bootdelay 5 ; "			\
 		"setenv boottype norm ; "		\
 	"fi"

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"verify=n\0" \
 	"consdev=ttyS0\0"						\
 	"baudrate=115200\0"						\
 	"bootscript=boot.scr\0"						\
 	"ubimtdnr=5\0"							\
 	"ubimtd=rootfs\0"						\
 	"ubipart=ubi0:rootfs\0"						\
 	"ubisfcs=1\0"		/* Default is flash at CS#1 */		\
 	"netdev=eth0\0"							\
 	"hostname=vining_fpga\0"						\
 	"kernel_addr_r=0x10000000\0"					\
 	"mtdparts_0=ff705000.spi.0:"					\
 		"1m(u-boot),"						\
 		"64k(env1),"						\
 		"64k(env2),"						\
 		"256k(samtec1),"					\
 		"256k(samtec2),"					\
 		"-(rcvrfs)\0"	/* Recovery */				\
 	"mtdparts_1=ff705000.spi.1:"					\
 		"32m(rootfs),"						\
 		"-(userfs)\0"						\
 	"update_filename=u-boot-with-spl-dtb.sfp\0"			\
 	"update_qspi_offset=0x0\0"					\
 	"update_qspi="		/* Update the QSPI firmware */		\
 		"if sf probe ; then "					\
 		"if tftp ${update_filename} ; then "			\
 		"sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \
 		"fi ; "							\
 		"fi\0"							\
 	"fpga_filename=output_file.rbf\0"				\
 	"load_fpga="		/* Load FPGA bitstream */		\
 		"if tftp ${fpga_filename} ; then "			\
 		"fpga load 0 $loadaddr $filesize ; "			\
 		"bridge enable ; "					\
 		"fi\0"							\
 	"addcons="							\
 		"setenv bootargs ${bootargs} "				\
 		"console=${consdev},${baudrate}\0"			\
 	"addip="							\
 		"setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
 			"${netmask}:${hostname}:${netdev}:off\0"	\
 	"addmisc="							\
 		"setenv bootargs ${bootargs} ${miscargs}\0"		\
 	"addmtd="							\
 		"setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; "	\
 		"setenv bootargs ${bootargs} mtdparts=${mtdparts}\0"	\
 	"addargs=run addcons addmtd addmisc\0"				\
 	"ubiload="							\
 		"ubi part ${ubimtd} ; ubifsmount ${ubipart} ; "		\
 		"ubifsload ${kernel_addr_r} /boot/${bootfile}\0"	\
 	"netload="							\
 		"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0"	\
 	"miscargs=nohlt panic=1\0"					\
 	"ubiargs="							\
 		"setenv bootargs ubi.mtd=${ubimtdnr} "			\
 		"root=${ubipart} rootfstype=ubifs\0"			\
 	"nfsargs="							\
 		"setenv bootargs root=/dev/nfs rw "			\
 			"nfsroot=${serverip}:${rootpath},v3,tcp\0"	\
 	"ubi_sfsel="							\
 		"if test \"${boottype}\" = \"rcvr\" ; then "		\
 			"setenv ubisfcs 0 ; "				\
 			"setenv ubimtd rcvrfs ; "			\
 			"setenv ubimtdnr 5 ; "				\
 			"setenv mtdparts mtdparts=${mtdparts_0} ; "	\
 			"setenv mtdids nor0=ff705000.spi.0 ; "		\
 			"setenv ubipart ubi0:rootfs ; "			\
 		"else "							\
 			"setenv ubisfcs 1 ; "				\
 			"setenv ubimtd rootfs ; "			\
 			"setenv ubimtdnr 6 ; "				\
 			"setenv mtdparts mtdparts=${mtdparts_1} ; "	\
 			"setenv mtdids nor0=ff705000.spi.1 ; "		\
 			"setenv ubipart ubi0:rootfs ; "			\
 		"fi ; "							\
 		"sf probe 0:${ubisfcs}\0"				\
 	"ubi_ubi="							\
 		"run ubi_sfsel ubiload ubiargs addargs ; "		\
 		"bootm ${kernel_addr_r}\0"				\
 	"ubi_nfs="							\
 		"run ubiload nfsargs addip addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"net_ubi="							\
 		"run netload ubiargs addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"net_nfs="							\
 		"run netload nfsargs addip addargs ; "			\
 		"bootm ${kernel_addr_r}\0"				\
 	"selboot="	/* Select from where to boot. */		\
 		"if test \"${bootmode}\" = \"qspi\" ; then "		\
 			"led all off ; "				\
 			"if test \"${boottype}\" = \"rcvr\" ; then "	\
 				"echo \"Booting recovery system\" ; "	\
 				"led 3 on ; "	/* Bottom RED */	\
 			"fi ; "						\
 			"led 1 on ; "		/* Top RED */		\
 			"run ubi_ubi ; "				\
 		"else echo \"Unsupported boot mode: \"${bootmode} ; "	\
 		"fi\0"							\

 #define CONFIG_CMD_UBIFS
 #define CONFIG_RBTREE
 #define CONFIG_LZO
 #define MTDPARTS_DEFAULT			\
 	"mtdparts=ff705000.spi.0:"		\
 		"1m(u-boot),"			\
 		"64k(env1),"			\
 		"64k(env2),"			\
 		"256k(samtec1),"		\
 		"256k(samtec2),"		\
 		"-(rcvrfs);"	/* Recovery */	\

 #define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 #define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
 #define CONFIG_ENV_SECT_SIZE		(64 * 1024)
 #define CONFIG_ENV_OFFSET		0x100000
 #define CONFIG_ENV_OFFSET_REDUND	\
 	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)

 #define CONFIG_MISC_INIT_R

 /* Support changing the prompt string */
 #define CONFIG_CMDLINE_PS_SUPPORT

 /* The rest of the configuration is shared */
 #include <configs/socfpga_common.h>

 #endif	/* __CONFIG_SAMTEC_VINING_FPGA_H__ */
	/*
	* Copyright (C) 2015 Marek Vasut <marex@denx.de>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/
	#ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
	#define __CONFIG_SAMTEC_VINING_FPGA_H__

	#include <asm/arch/base_addr_ac5.h>

	/* U-Boot Commands */
	#define CONFIG_SYS_NO_FLASH
	#define CONFIG_DOS_PARTITION
	#define CONFIG_FAT_WRITE
	#define CONFIG_HW_WATCHDOG

	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_LED

	/* Memory configurations */
	#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on VINING_FPGA */

	/* Booting Linux */
	#define CONFIG_BOOTFILE "openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
	#define CONFIG_BOOTARGS "console=ttyS0," __stringify(CONFIG_BAUDRATE)
	#define CONFIG_BOOTCOMMAND "run selboot"
	#define CONFIG_LOADADDR 0x01000000
	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	/* I2C EEPROM */
	#ifdef CONFIG_CMD_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_I2C_EEPROM_BUS 0
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
	#endif

	/*
	* Status LEDs:
	* 0 ... Top Green
	* 1 ... Top Red
	* 2 ... Bottom Green
	* 3 ... Bottom Red
	*/
	#define CONFIG_STATUS_LED
	#define CONFIG_GPIO_LED
	#define CONFIG_BOARD_SPECIFIC_LED
	#define STATUS_LED_BIT 48
	#define STATUS_LED_STATE STATUS_LED_OFF
	#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
	#define STATUS_LED_BIT1 53
	#define STATUS_LED_STATE1 STATUS_LED_OFF
	#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
	#define STATUS_LED_BIT2 54
	#define STATUS_LED_STATE2 STATUS_LED_OFF
	#define STATUS_LED_PERIOD2 (CONFIG_SYS_HZ / 2)
	#define STATUS_LED_BIT3 65
	#define STATUS_LED_STATE3 STATUS_LED_OFF
	#define STATUS_LED_PERIOD3 (CONFIG_SYS_HZ / 2)

	/* Ethernet on SoC (EMAC) */
	#if defined(CONFIG_CMD_NET)
	#define CONFIG_BOOTP_SEND_HOSTNAME
	/* PHY */
	#define CONFIG_PHY_MICREL
	#define CONFIG_PHY_MICREL_KSZ9021
	#endif

	/* Extra Environment */
	#define CONFIG_HOSTNAME socfpga_vining_fpga

	/*
	* Active LOW GPIO buttons:
	* A: GPIO 77 ... the button between USB B and ethernet
	* B: GPIO 78 ... the button between USB A ports
	*
	* The logic:
	* if button B is not pressed, boot normal Linux system immediatelly
	* if button B is pressed, wait $bootdelay and boot recovery system
	*/
	#define CONFIG_PREBOOT \
	"setenv hostname vining-${unit_serial} ; " \
	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; " \
	"if gpio input 78 ; then " \
	"setenv bootdelay 10 ; " \
	"setenv boottype rcvr ; " \
	"else " \
	"setenv bootdelay 5 ; " \
	"setenv boottype norm ; " \
	"fi"

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"verify=n\0" \
	"consdev=ttyS0\0" \
	"baudrate=115200\0" \
	"bootscript=boot.scr\0" \
	"ubimtdnr=5\0" \
	"ubimtd=rootfs\0" \
	"ubipart=ubi0:rootfs\0" \
	"ubisfcs=1\0" /* Default is flash at CS#1 */ \
	"netdev=eth0\0" \
	"hostname=vining_fpga\0" \
	"kernel_addr_r=0x10000000\0" \
	"mtdparts_0=ff705000.spi.0:" \
	"1m(u-boot)," \
	"64k(env1)," \
	"64k(env2)," \
	"256k(samtec1)," \
	"256k(samtec2)," \
	"-(rcvrfs)\0" /* Recovery */ \
	"mtdparts_1=ff705000.spi.1:" \
	"32m(rootfs)," \
	"-(userfs)\0" \
	"update_filename=u-boot-with-spl-dtb.sfp\0" \
	"update_qspi_offset=0x0\0" \
	"update_qspi=" /* Update the QSPI firmware */ \
	"if sf probe ; then " \
	"if tftp ${update_filename} ; then " \
	"sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \
	"fi ; " \
	"fi\0" \
	"fpga_filename=output_file.rbf\0" \
	"load_fpga=" /* Load FPGA bitstream */ \
	"if tftp ${fpga_filename} ; then " \
	"fpga load 0 $loadaddr $filesize ; " \
	"bridge enable ; " \
	"fi\0" \
	"addcons=" \
	"setenv bootargs ${bootargs} " \
	"console=${consdev},${baudrate}\0" \
	"addip=" \
	"setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:" \
	"${netmask}:${hostname}:${netdev}:off\0" \
	"addmisc=" \
	"setenv bootargs ${bootargs} ${miscargs}\0" \
	"addmtd=" \
	"setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; " \
	"setenv bootargs ${bootargs} mtdparts=${mtdparts}\0" \
	"addargs=run addcons addmtd addmisc\0" \
	"ubiload=" \
	"ubi part ${ubimtd} ; ubifsmount ${ubipart} ; " \
	"ubifsload ${kernel_addr_r} /boot/${bootfile}\0" \
	"netload=" \
	"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0" \
	"miscargs=nohlt panic=1\0" \
	"ubiargs=" \
	"setenv bootargs ubi.mtd=${ubimtdnr} " \
	"root=${ubipart} rootfstype=ubifs\0" \
	"nfsargs=" \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath},v3,tcp\0" \
	"ubi_sfsel=" \
	"if test \"${boottype}\" = \"rcvr\" ; then " \
	"setenv ubisfcs 0 ; " \
	"setenv ubimtd rcvrfs ; " \
	"setenv ubimtdnr 5 ; " \
	"setenv mtdparts mtdparts=${mtdparts_0} ; " \
	"setenv mtdids nor0=ff705000.spi.0 ; " \
	"setenv ubipart ubi0:rootfs ; " \
	"else " \
	"setenv ubisfcs 1 ; " \
	"setenv ubimtd rootfs ; " \
	"setenv ubimtdnr 6 ; " \
	"setenv mtdparts mtdparts=${mtdparts_1} ; " \
	"setenv mtdids nor0=ff705000.spi.1 ; " \
	"setenv ubipart ubi0:rootfs ; " \
	"fi ; " \
	"sf probe 0:${ubisfcs}\0" \
	"ubi_ubi=" \
	"run ubi_sfsel ubiload ubiargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"ubi_nfs=" \
	"run ubiload nfsargs addip addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"net_ubi=" \
	"run netload ubiargs addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"net_nfs=" \
	"run netload nfsargs addip addargs ; " \
	"bootm ${kernel_addr_r}\0" \
	"selboot=" /* Select from where to boot. */ \
	"if test \"${bootmode}\" = \"qspi\" ; then " \
	"led all off ; " \
	"if test \"${boottype}\" = \"rcvr\" ; then " \
	"echo \"Booting recovery system\" ; " \
	"led 3 on ; " /* Bottom RED */ \
	"fi ; " \
	"led 1 on ; " /* Top RED */ \
	"run ubi_ubi ; " \
	"else echo \"Unsupported boot mode: \"${bootmode} ; " \
	"fi\0" \

	#define CONFIG_CMD_UBIFS
	#define CONFIG_RBTREE
	#define CONFIG_LZO
	#define MTDPARTS_DEFAULT \
	"mtdparts=ff705000.spi.0:" \
	"1m(u-boot)," \
	"64k(env1)," \
	"64k(env2)," \
	"256k(samtec1)," \
	"256k(samtec2)," \
	"-(rcvrfs);" /* Recovery */ \

	#define CONFIG_ENV_IS_IN_SPI_FLASH
	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	#define CONFIG_ENV_SECT_SIZE (64 * 1024)
	#define CONFIG_ENV_OFFSET 0x100000
	#define CONFIG_ENV_OFFSET_REDUND \
	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)

	#define CONFIG_MISC_INIT_R

	/* Support changing the prompt string */
	#define CONFIG_CMDLINE_PS_SUPPORT

	/* The rest of the configuration is shared */
	#include <configs/socfpga_common.h>

	#endif /* __CONFIG_SAMTEC_VINING_FPGA_H__ */