| /* |
| * (C) Copyright 2007 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <ppc_asm.tmpl> |
| #include <config.h> |
| #include <asm/mmu.h> |
| #include <asm/ppc4xx.h> |
| |
| /************************************************************************** |
| * TLB TABLE |
| * |
| * This table is used by the cpu boot code to setup the initial tlb |
| * entries. Rather than make broad assumptions in the cpu source tree, |
| * this table lets each board set things up however they like. |
| * |
| * Pointer to the table is returned in r1 |
| * |
| *************************************************************************/ |
| |
| .section .bootpg,"ax" |
| |
| /************************************************************************** |
| * TLB table for revA |
| *************************************************************************/ |
| .globl tlbtabA |
| tlbtabA: |
| tlbtab_start |
| |
| /* |
| * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the |
| * speed up boot process. It is patched after relocation to enable SA_I |
| */ |
| tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_RWX | SA_G) |
| |
| /* |
| * TLB entries for SDRAM are not needed on this platform. |
| * They are dynamically generated in the SPD DDR(2) detection |
| * routine. |
| */ |
| |
| tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_RWX | SA_I) |
| tlbentry(CONFIG_SYS_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_RW | SA_I) |
| |
| tlbentry(CONFIG_SYS_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_RWX | SA_IG) |
| tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_RW | SA_IG) |
| |
| tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE_BASE, SZ_16K, 0x20000000, 0xC, AC_RW | SA_IG) |
| |
| tlbentry(CONFIG_SYS_PCIE0_CFGBASE, SZ_16M, 0x40000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE1_CFGBASE, SZ_16M, 0x80000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE2_CFGBASE, SZ_16M, 0xC0000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE0_XCFGBASE, SZ_1K, 0x50000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE1_XCFGBASE, SZ_1K, 0x90000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE2_XCFGBASE, SZ_1K, 0xD0000000, 0xC, AC_RW | SA_IG) |
| tlbtab_end |
| |
| /************************************************************************** |
| * TLB table for revB |
| * |
| * Notice: revB of the 440SPe chip is very strict about PLB real addresses |
| * and ranges to be mapped for config space: it seems to only work with |
| * d_nnnn_nnnn range (hangs the core upon config transaction attempts when |
| * set otherwise) while revA uses c_nnnn_nnnn. |
| *************************************************************************/ |
| .globl tlbtabB |
| tlbtabB: |
| tlbtab_start |
| |
| /* |
| * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the |
| * speed up boot process. It is patched after relocation to enable SA_I |
| */ |
| tlbentry(0xff000000, SZ_16M, 0xff000000, 4, AC_RWX | SA_G) |
| |
| /* |
| * TLB entries for SDRAM are not needed on this platform. |
| * They are dynamically generated in the SPD DDR(2) detection |
| * routine. |
| */ |
| |
| tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_RWX | SA_I) |
| tlbentry(CONFIG_SYS_FPGA_BASE, SZ_1K, 0xE2000000, 4,AC_RW | SA_I) |
| |
| tlbentry(CONFIG_SYS_OPER_FLASH, SZ_16M, 0xE7000000, 4,AC_RWX | SA_IG) |
| tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_RW | SA_IG) |
| |
| tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE_MEMBASE, SZ_256M, 0xB0000000, 0xD, AC_RW | SA_IG) |
| |
| tlbentry(CONFIG_SYS_PCIE0_CFGBASE, SZ_16M, 0x00000000, 0xD, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE1_CFGBASE, SZ_16M, 0x20000000, 0xD, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE2_CFGBASE, SZ_16M, 0x40000000, 0xD, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE0_XCFGBASE, SZ_1K, 0x10000000, 0xD, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE1_XCFGBASE, SZ_1K, 0x30000000, 0xD, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCIE2_XCFGBASE, SZ_1K, 0x50000000, 0xD, AC_RW | SA_IG) |
| tlbtab_end |