| /* |
| * Copyright (C) Marvell International Ltd. and its affiliates |
| * |
| * SPDX-License-Identifier: GPL-2.0 |
| */ |
| |
| #include <common.h> |
| #include <i2c.h> |
| #include <spl.h> |
| #include <asm/io.h> |
| #include <asm/arch/cpu.h> |
| #include <asm/arch/soc.h> |
| |
| #include "ddr3_hw_training.h" |
| |
| /* |
| * Debug |
| */ |
| #define DEBUG_DFS_C(s, d, l) \ |
| DEBUG_DFS_S(s); DEBUG_DFS_D(d, l); DEBUG_DFS_S("\n") |
| #define DEBUG_DFS_FULL_C(s, d, l) \ |
| DEBUG_DFS_FULL_S(s); DEBUG_DFS_FULL_D(d, l); DEBUG_DFS_FULL_S("\n") |
| |
| #ifdef MV_DEBUG_DFS |
| #define DEBUG_DFS_S(s) puts(s) |
| #define DEBUG_DFS_D(d, l) printf("%x", d) |
| #else |
| #define DEBUG_DFS_S(s) |
| #define DEBUG_DFS_D(d, l) |
| #endif |
| |
| #ifdef MV_DEBUG_DFS_FULL |
| #define DEBUG_DFS_FULL_S(s) puts(s) |
| #define DEBUG_DFS_FULL_D(d, l) printf("%x", d) |
| #else |
| #define DEBUG_DFS_FULL_S(s) |
| #define DEBUG_DFS_FULL_D(d, l) |
| #endif |
| |
| #if defined(MV88F672X) |
| extern u8 div_ratio[CLK_VCO][CLK_DDR]; |
| extern void get_target_freq(u32 freq_mode, u32 *ddr_freq, u32 *hclk_ps); |
| #else |
| extern u16 odt_dynamic[ODT_OPT][MAX_CS]; |
| extern u8 div_ratio1to1[CLK_CPU][CLK_DDR]; |
| extern u8 div_ratio2to1[CLK_CPU][CLK_DDR]; |
| #endif |
| extern u16 odt_static[ODT_OPT][MAX_CS]; |
| |
| extern u32 cpu_fab_clk_to_hclk[FAB_OPT][CLK_CPU]; |
| |
| extern u32 ddr3_get_vco_freq(void); |
| |
| u32 ddr3_get_freq_parameter(u32 target_freq, int ratio_2to1); |
| |
| #ifdef MV_DEBUG_DFS |
| static inline void dfs_reg_write(u32 addr, u32 val) |
| { |
| printf("\n write reg 0x%08x = 0x%08x", addr, val); |
| writel(val, INTER_REGS_BASE + addr); |
| } |
| #else |
| static inline void dfs_reg_write(u32 addr, u32 val) |
| { |
| writel(val, INTER_REGS_BASE + addr); |
| } |
| #endif |
| |
| static void wait_refresh_op_complete(void) |
| { |
| u32 reg; |
| |
| /* Poll - Wait for Refresh operation completion */ |
| do { |
| reg = reg_read(REG_SDRAM_OPERATION_ADDR) & |
| REG_SDRAM_OPERATION_CMD_RFRS_DONE; |
| } while (reg); /* Wait for '0' */ |
| } |
| |
| /* |
| * Name: ddr3_get_freq_parameter |
| * Desc: Finds CPU/DDR frequency ratio according to Sample@reset and table. |
| * Args: target_freq - target frequency |
| * Notes: |
| * Returns: freq_par - the ratio parameter |
| */ |
| u32 ddr3_get_freq_parameter(u32 target_freq, int ratio_2to1) |
| { |
| u32 ui_vco_freq, freq_par; |
| |
| ui_vco_freq = ddr3_get_vco_freq(); |
| |
| #if defined(MV88F672X) |
| freq_par = div_ratio[ui_vco_freq][target_freq]; |
| #else |
| /* Find the ratio between PLL frequency and ddr-clk */ |
| if (ratio_2to1) |
| freq_par = div_ratio2to1[ui_vco_freq][target_freq]; |
| else |
| freq_par = div_ratio1to1[ui_vco_freq][target_freq]; |
| #endif |
| |
| return freq_par; |
| } |
| |
| /* |
| * Name: ddr3_dfs_high_2_low |
| * Desc: |
| * Args: freq - target frequency |
| * Notes: |
| * Returns: MV_OK - success, MV_FAIL - fail |
| */ |
| int ddr3_dfs_high_2_low(u32 freq, MV_DRAM_INFO *dram_info) |
| { |
| #if defined(MV88F78X60) || defined(MV88F672X) |
| /* This Flow is relevant for ArmadaXP A0 */ |
| u32 reg, freq_par, tmp; |
| u32 cs = 0; |
| |
| DEBUG_DFS_C("DDR3 - DFS - High To Low - Starting DFS procedure to Frequency - ", |
| freq, 1); |
| |
| /* target frequency - 100MHz */ |
| freq_par = ddr3_get_freq_parameter(freq, 0); |
| |
| #if defined(MV88F672X) |
| u32 hclk; |
| u32 cpu_freq = ddr3_get_cpu_freq(); |
| get_target_freq(cpu_freq, &tmp, &hclk); |
| #endif |
| |
| /* Configure - DRAM DLL final state after DFS is complete - Enable */ |
| reg = reg_read(REG_DFS_ADDR); |
| /* [0] - DfsDllNextState - Disable */ |
| reg |= (1 << REG_DFS_DLLNEXTSTATE_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Configure - XBAR Retry response during Block to enable internal |
| * access - Disable |
| */ |
| reg = reg_read(REG_METAL_MASK_ADDR); |
| /* [0] - RetryMask - Disable */ |
| reg &= ~(1 << REG_METAL_MASK_RETRY_OFFS); |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| /* Configure - Block new external transactions - Enable */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg |= (1 << REG_DFS_BLOCK_OFFS); /* [1] - DfsBlock - Enable */ |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Registered DIMM support */ |
| if (dram_info->reg_dimm) { |
| /* |
| * Configure - Disable Register DIMM CKE Power |
| * Down mode - CWA_RC |
| */ |
| reg = (0x9 & REG_SDRAM_OPERATION_CWA_RC_MASK) << |
| REG_SDRAM_OPERATION_CWA_RC_OFFS; |
| /* |
| * Configure - Disable Register DIMM CKE Power |
| * Down mode - CWA_DATA |
| */ |
| reg |= ((0 & REG_SDRAM_OPERATION_CWA_DATA_MASK) << |
| REG_SDRAM_OPERATION_CWA_DATA_OFFS); |
| |
| /* |
| * Configure - Disable Register DIMM CKE Power |
| * Down mode - Set Delay - tMRD |
| */ |
| reg |= (0 << REG_SDRAM_OPERATION_CWA_DELAY_SEL_OFFS); |
| |
| /* Configure - Issue CWA command with the above parameters */ |
| reg |= (REG_SDRAM_OPERATION_CMD_CWA & |
| ~(0xF << REG_SDRAM_OPERATION_CS_OFFS)); |
| |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for CWA operation completion */ |
| do { |
| reg = reg_read(REG_SDRAM_OPERATION_ADDR) & |
| (REG_SDRAM_OPERATION_CMD_MASK); |
| } while (reg); |
| |
| /* Configure - Disable outputs floating during Self Refresh */ |
| reg = reg_read(REG_REGISTERED_DRAM_CTRL_ADDR); |
| /* [15] - SRFloatEn - Disable */ |
| reg &= ~(1 << REG_REGISTERED_DRAM_CTRL_SR_FLOAT_OFFS); |
| /* 0x16D0 - DDR3 Registered DRAM Control */ |
| dfs_reg_write(REG_REGISTERED_DRAM_CTRL_ADDR, reg); |
| } |
| |
| /* Optional - Configure - DDR3_Rtt_nom_CS# */ |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) { |
| reg = reg_read(REG_DDR3_MR1_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS)); |
| reg &= REG_DDR3_MR1_RTT_MASK; |
| dfs_reg_write(REG_DDR3_MR1_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS), reg); |
| } |
| } |
| |
| /* Configure - Move DRAM into Self Refresh */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg |= (1 << REG_DFS_SR_OFFS); /* [2] - DfsSR - Enable */ |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Poll - Wait for Self Refresh indication */ |
| do { |
| reg = ((reg_read(REG_DFS_ADDR)) & (1 << REG_DFS_ATSR_OFFS)); |
| } while (reg == 0x0); /* 0x1528 [3] - DfsAtSR - Wait for '1' */ |
| |
| /* Start of clock change procedure (PLL) */ |
| #if defined(MV88F672X) |
| /* avantaLP */ |
| /* Configure cpupll_clkdiv_reset_mask */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL0); |
| reg &= CPU_PLL_CLOCK_DIVIDER_CNTRL0_MASK; |
| /* 0xE8264[7:0] 0xff CPU Clock Dividers Reset mask */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL0, (reg + 0xFF)); |
| |
| /* Configure cpu_clkdiv_reload_smooth */ |
| reg = reg_read(CPU_PLL_CNTRL0); |
| reg &= CPU_PLL_CNTRL0_RELOAD_SMOOTH_MASK; |
| /* 0xE8260 [15:8] 0x2 CPU Clock Dividers Reload Smooth enable */ |
| dfs_reg_write(CPU_PLL_CNTRL0, |
| (reg + (2 << CPU_PLL_CNTRL0_RELOAD_SMOOTH_OFFS))); |
| |
| /* Configure cpupll_clkdiv_relax_en */ |
| reg = reg_read(CPU_PLL_CNTRL0); |
| reg &= CPU_PLL_CNTRL0_RELAX_EN_MASK; |
| /* 0xE8260 [31:24] 0x2 Relax Enable */ |
| dfs_reg_write(CPU_PLL_CNTRL0, |
| (reg + (2 << CPU_PLL_CNTRL0_RELAX_EN_OFFS))); |
| |
| /* Configure cpupll_clkdiv_ddr_clk_ratio */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL1); |
| /* |
| * 0xE8268 [13:8] N Set Training clock: |
| * APLL Out Clock (VCO freq) / N = 100 MHz |
| */ |
| reg &= CPU_PLL_CLOCK_DIVIDER_CNTRL1_MASK; |
| reg |= (freq_par << 8); /* full Integer ratio from PLL-out to ddr-clk */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL1, reg); |
| |
| /* Configure cpupll_clkdiv_reload_ratio */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL0); |
| reg &= CPU_PLL_CLOCK_RELOAD_RATIO_MASK; |
| /* 0xE8264 [8]=0x1 CPU Clock Dividers Reload Ratio trigger set */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL0, |
| (reg + (1 << CPU_PLL_CLOCK_RELOAD_RATIO_OFFS))); |
| |
| udelay(1); |
| |
| /* Configure cpupll_clkdiv_reload_ratio */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL0); |
| reg &= CPU_PLL_CLOCK_RELOAD_RATIO_MASK; |
| /* 0xE8264 [8]=0x0 CPU Clock Dividers Reload Ratio trigger clear */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL0, reg); |
| |
| udelay(5); |
| |
| #else |
| /* |
| * Initial Setup - assure that the "load new ratio" is clear (bit 24) |
| * and in the same chance, block reassertions of reset [15:8] and |
| * force reserved bits[7:0]. |
| */ |
| reg = 0x0000FDFF; |
| /* 0x18700 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| /* |
| * RelaX whenever reset is asserted to that channel |
| * (good for any case) |
| */ |
| reg = 0x0000FF00; |
| /* 0x18704 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_1_ADDR, reg); |
| |
| reg = reg_read(REG_CPU_DIV_CLK_CTRL_2_ADDR) & |
| REG_CPU_DIV_CLK_CTRL_3_FREQ_MASK; |
| |
| /* full Integer ratio from PLL-out to ddr-clk */ |
| reg |= (freq_par << REG_CPU_DIV_CLK_CTRL_3_FREQ_OFFS); |
| /* 0x1870C - CPU Div CLK control 3 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_2_ADDR, reg); |
| |
| /* |
| * Shut off clock enable to the DDRPHY clock channel (this is the "D"). |
| * All the rest are kept as is (forced, but could be read-modify-write). |
| * This is done now by RMW above. |
| */ |
| |
| /* Clock is not shut off gracefully - keep it running */ |
| reg = 0x000FFF02; |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_4_ADDR, reg); |
| |
| /* Wait before replacing the clock on the DDR Phy Channel. */ |
| udelay(1); |
| |
| /* |
| * This for triggering the frequency update. Bit[24] is the |
| * central control |
| * bits [23:16] == which channels to change ==2 ==> |
| * only DDR Phy (smooth transition) |
| * bits [15:8] == mask reset reassertion due to clock modification |
| * to these channels. |
| * bits [7:0] == not in use |
| */ |
| reg = 0x0102FDFF; |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| udelay(1); /* Wait 1usec */ |
| |
| /* |
| * Poll Div CLK status 0 register - indication that the clocks |
| * are active - 0x18718 [8] |
| */ |
| do { |
| reg = (reg_read(REG_CPU_DIV_CLK_STATUS_0_ADDR)) & |
| (1 << REG_CPU_DIV_CLK_ALL_STABLE_OFFS); |
| } while (reg == 0); |
| |
| /* |
| * Clean the CTRL0, to be ready for next resets and next requests |
| * of ratio modifications. |
| */ |
| reg = 0x000000FF; |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| udelay(5); |
| #endif |
| /* End of clock change procedure (PLL) */ |
| |
| /* Configure - Select normal clock for the DDR PHY - Enable */ |
| reg = reg_read(REG_DRAM_INIT_CTRL_STATUS_ADDR); |
| /* [16] - ddr_phy_trn_clk_sel - Enable */ |
| reg |= (1 << REG_DRAM_INIT_CTRL_TRN_CLK_OFFS); |
| /* 0x18488 - DRAM Init control status register */ |
| dfs_reg_write(REG_DRAM_INIT_CTRL_STATUS_ADDR, reg); |
| |
| /* Configure - Set Correct Ratio - 1:1 */ |
| /* [15] - Phy2UnitClkRatio = 0 - Set 1:1 Ratio between Dunit and Phy */ |
| |
| reg = reg_read(REG_DDR_IO_ADDR) & ~(1 << REG_DDR_IO_CLK_RATIO_OFFS); |
| dfs_reg_write(REG_DDR_IO_ADDR, reg); /* 0x1524 - DDR IO Register */ |
| |
| /* Configure - 2T Mode - Restore original configuration */ |
| reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR); |
| /* [3:4] 2T - 1T Mode - low freq */ |
| reg &= ~(REG_DUNIT_CTRL_LOW_2T_MASK << REG_DUNIT_CTRL_LOW_2T_OFFS); |
| /* 0x1404 - DDR Controller Control Low Register */ |
| dfs_reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); |
| |
| /* Configure - Restore CL and CWL - MRS Commands */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg &= ~(REG_DFS_CL_NEXT_STATE_MASK << REG_DFS_CL_NEXT_STATE_OFFS); |
| reg &= ~(REG_DFS_CWL_NEXT_STATE_MASK << REG_DFS_CWL_NEXT_STATE_OFFS); |
| /* [8] - DfsCLNextState - MRS CL=6 after DFS (due to DLL-off mode) */ |
| reg |= (0x4 << REG_DFS_CL_NEXT_STATE_OFFS); |
| /* [12] - DfsCWLNextState - MRS CWL=6 after DFS (due to DLL-off mode) */ |
| reg |= (0x1 << REG_DFS_CWL_NEXT_STATE_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Poll - Wait for APLL + ADLLs lock on new frequency */ |
| do { |
| reg = (reg_read(REG_PHY_LOCK_STATUS_ADDR)) & |
| REG_PHY_LOCK_APLL_ADLL_STATUS_MASK; |
| /* 0x1674 [10:0] - Phy lock status Register */ |
| } while (reg != REG_PHY_LOCK_APLL_ADLL_STATUS_MASK); |
| |
| /* Configure - Reset the PHY Read FIFO and Write channels - Set Reset */ |
| reg = (reg_read(REG_SDRAM_CONFIG_ADDR) & REG_SDRAM_CONFIG_MASK); |
| /* [30:29] = 0 - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* |
| * Configure - DRAM Data PHY Read [30], Write [29] path |
| * reset - Release Reset |
| */ |
| reg = (reg_read(REG_SDRAM_CONFIG_ADDR) | ~REG_SDRAM_CONFIG_MASK); |
| /* [30:29] = '11' - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* Registered DIMM support */ |
| if (dram_info->reg_dimm) { |
| /* |
| * Configure - Change register DRAM operating speed |
| * (below 400MHz) - CWA_RC |
| */ |
| reg = (0xA & REG_SDRAM_OPERATION_CWA_RC_MASK) << |
| REG_SDRAM_OPERATION_CWA_RC_OFFS; |
| |
| /* |
| * Configure - Change register DRAM operating speed |
| * (below 400MHz) - CWA_DATA |
| */ |
| reg |= ((0x0 & REG_SDRAM_OPERATION_CWA_DATA_MASK) << |
| REG_SDRAM_OPERATION_CWA_DATA_OFFS); |
| |
| /* Configure - Set Delay - tSTAB */ |
| reg |= (0x1 << REG_SDRAM_OPERATION_CWA_DELAY_SEL_OFFS); |
| |
| /* Configure - Issue CWA command with the above parameters */ |
| reg |= (REG_SDRAM_OPERATION_CMD_CWA & |
| ~(0xF << REG_SDRAM_OPERATION_CS_OFFS)); |
| |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for CWA operation completion */ |
| do { |
| reg = reg_read(REG_SDRAM_OPERATION_ADDR) & |
| (REG_SDRAM_OPERATION_CMD_MASK); |
| } while (reg); |
| } |
| |
| /* Configure - Exit Self Refresh */ |
| /* [2] - DfsSR */ |
| reg = (reg_read(REG_DFS_ADDR) & ~(1 << REG_DFS_SR_OFFS)); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Poll - DFS Register - 0x1528 [3] - DfsAtSR - All DRAM devices |
| * on all ranks are NOT in self refresh mode |
| */ |
| do { |
| reg = ((reg_read(REG_DFS_ADDR)) & (1 << REG_DFS_ATSR_OFFS)); |
| } while (reg); /* Wait for '0' */ |
| |
| /* Configure - Issue Refresh command */ |
| /* [3-0] = 0x2 - Refresh Command, [11-8] - enabled Cs */ |
| reg = REG_SDRAM_OPERATION_CMD_RFRS; |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) |
| reg &= ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| } |
| |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| /* Configure - Block new external transactions - Disable */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg &= ~(1 << REG_DFS_BLOCK_OFFS); /* [1] - DfsBlock - Disable */ |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Configure - XBAR Retry response during Block to enable |
| * internal access - Disable |
| */ |
| reg = reg_read(REG_METAL_MASK_ADDR); |
| /* [0] - RetryMask - Enable */ |
| reg |= (1 << REG_METAL_MASK_RETRY_OFFS); |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) { |
| /* Configure - Set CL */ |
| reg = reg_read(REG_DDR3_MR0_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS)) & |
| ~REG_DDR3_MR0_CL_MASK; |
| tmp = 0x4; /* CL=6 - 0x4 */ |
| reg |= ((tmp & 0x1) << REG_DDR3_MR0_CL_OFFS); |
| reg |= ((tmp & 0xE) << REG_DDR3_MR0_CL_HIGH_OFFS); |
| dfs_reg_write(REG_DDR3_MR0_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS), reg); |
| |
| /* Configure - Set CWL */ |
| reg = reg_read(REG_DDR3_MR2_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS)) |
| & ~(REG_DDR3_MR2_CWL_MASK << REG_DDR3_MR2_CWL_OFFS); |
| /* CWL=6 - 0x1 */ |
| reg |= ((0x1) << REG_DDR3_MR2_CWL_OFFS); |
| dfs_reg_write(REG_DDR3_MR2_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS), reg); |
| } |
| } |
| |
| DEBUG_DFS_C("DDR3 - DFS - High To Low - Ended successfuly - new Frequency - ", |
| freq, 1); |
| |
| return MV_OK; |
| #else |
| /* This Flow is relevant for Armada370 A0 and ArmadaXP Z1 */ |
| |
| u32 reg, freq_par; |
| u32 cs = 0; |
| |
| DEBUG_DFS_C("DDR3 - DFS - High To Low - Starting DFS procedure to Frequency - ", |
| freq, 1); |
| |
| /* target frequency - 100MHz */ |
| freq_par = ddr3_get_freq_parameter(freq, 0); |
| |
| reg = 0x0000FF00; |
| /* 0x18700 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_1_ADDR, reg); |
| |
| /* 0x1600 - ODPG_CNTRL_Control */ |
| reg = reg_read(REG_ODPG_CNTRL_ADDR); |
| /* [21] = 1 - auto refresh disable */ |
| reg |= (1 << REG_ODPG_CNTRL_OFFS); |
| dfs_reg_write(REG_ODPG_CNTRL_ADDR, reg); |
| |
| /* 0x1670 - PHY lock mask register */ |
| reg = reg_read(REG_PHY_LOCK_MASK_ADDR); |
| reg &= REG_PHY_LOCK_MASK_MASK; /* [11:0] = 0 */ |
| dfs_reg_write(REG_PHY_LOCK_MASK_ADDR, reg); |
| |
| reg = reg_read(REG_DFS_ADDR); /* 0x1528 - DFS register */ |
| |
| /* Disable reconfig */ |
| reg &= ~0x10; /* [4] - Enable reconfig MR registers after DFS_ERG */ |
| reg |= 0x1; /* [0] - DRAM DLL disabled after DFS */ |
| |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| reg = reg_read(REG_METAL_MASK_ADDR) & ~(1 << 0); /* [0] - disable */ |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| /* [1] - DFS Block enable */ |
| reg = reg_read(REG_DFS_ADDR) | (1 << REG_DFS_BLOCK_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* [2] - DFS Self refresh enable */ |
| reg = reg_read(REG_DFS_ADDR) | (1 << REG_DFS_SR_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Poll DFS Register - 0x1528 [3] - DfsAtSR - |
| * All DRAM devices on all ranks are in self refresh mode - |
| * DFS can be executed afterwards |
| */ |
| do { |
| reg = reg_read(REG_DFS_ADDR) & (1 << REG_DFS_ATSR_OFFS); |
| } while (reg == 0x0); /* Wait for '1' */ |
| |
| /* Disable ODT on DLL-off mode */ |
| dfs_reg_write(REG_SDRAM_ODT_CTRL_HIGH_ADDR, |
| REG_SDRAM_ODT_CTRL_HIGH_OVRD_MASK); |
| |
| /* [11:0] = 0 */ |
| reg = (reg_read(REG_PHY_LOCK_MASK_ADDR) & REG_PHY_LOCK_MASK_MASK); |
| /* 0x1670 - PHY lock mask register */ |
| dfs_reg_write(REG_PHY_LOCK_MASK_ADDR, reg); |
| |
| /* Add delay between entering SR and start ratio modification */ |
| udelay(1); |
| |
| /* |
| * Initial Setup - assure that the "load new ratio" is clear (bit 24) |
| * and in the same chance, block reassertions of reset [15:8] and |
| * force reserved bits[7:0]. |
| */ |
| reg = 0x0000FDFF; |
| /* 0x18700 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| /* |
| * RelaX whenever reset is asserted to that channel (good for any case) |
| */ |
| reg = 0x0000FF00; |
| /* 0x18700 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_1_ADDR, reg); |
| |
| reg = reg_read(REG_CPU_DIV_CLK_CTRL_3_ADDR) & |
| REG_CPU_DIV_CLK_CTRL_3_FREQ_MASK; |
| /* Full Integer ratio from PLL-out to ddr-clk */ |
| reg |= (freq_par << REG_CPU_DIV_CLK_CTRL_3_FREQ_OFFS); |
| /* 0x1870C - CPU Div CLK control 3 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_3_ADDR, reg); |
| |
| /* |
| * Shut off clock enable to the DDRPHY clock channel (this is the "D"). |
| * All the rest are kept as is (forced, but could be read-modify-write). |
| * This is done now by RMW above. |
| */ |
| |
| /* Clock is not shut off gracefully - keep it running */ |
| reg = 0x000FFF02; |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_4_ADDR, reg); |
| |
| /* Wait before replacing the clock on the DDR Phy Channel. */ |
| udelay(1); |
| |
| /* |
| * This for triggering the frequency update. Bit[24] is the |
| * central control |
| * bits [23:16] == which channels to change ==2 ==> only DDR Phy |
| * (smooth transition) |
| * bits [15:8] == mask reset reassertion due to clock modification |
| * to these channels. |
| * bits [7:0] == not in use |
| */ |
| reg = 0x0102FDFF; |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| udelay(1); /* Wait 1usec */ |
| |
| /* |
| * Poll Div CLK status 0 register - indication that the clocks |
| * are active - 0x18718 [8] |
| */ |
| do { |
| reg = (reg_read(REG_CPU_DIV_CLK_STATUS_0_ADDR)) & |
| (1 << REG_CPU_DIV_CLK_ALL_STABLE_OFFS); |
| } while (reg == 0); |
| |
| /* |
| * Clean the CTRL0, to be ready for next resets and next requests of |
| * ratio modifications. |
| */ |
| reg = 0x000000FF; |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| udelay(5); |
| |
| /* Switch HCLK Mux to training clk (100Mhz), keep DFS request bit */ |
| reg = 0x20050000; |
| /* 0x18488 - DRAM Init control status register */ |
| dfs_reg_write(REG_DRAM_INIT_CTRL_STATUS_ADDR, reg); |
| |
| reg = reg_read(REG_DDR_IO_ADDR) & ~(1 << REG_DDR_IO_CLK_RATIO_OFFS); |
| /* [15] = 0 - Set 1:1 Ratio between Dunit and Phy */ |
| dfs_reg_write(REG_DDR_IO_ADDR, reg); /* 0x1524 - DDR IO Regist */ |
| |
| reg = reg_read(REG_DRAM_PHY_CONFIG_ADDR) & REG_DRAM_PHY_CONFIG_MASK; |
| /* [31:30]] - reset pup data ctrl ADLL */ |
| /* 0x15EC - DRAM PHY Config register */ |
| dfs_reg_write(REG_DRAM_PHY_CONFIG_ADDR, reg); |
| |
| reg = (reg_read(REG_DRAM_PHY_CONFIG_ADDR) | ~REG_DRAM_PHY_CONFIG_MASK); |
| /* [31:30] - normal pup data ctrl ADLL */ |
| /* 0x15EC - DRAM PHY Config register */ |
| dfs_reg_write(REG_DRAM_PHY_CONFIG_ADDR, reg); |
| |
| udelay(1); /* Wait 1usec */ |
| |
| /* 0x1404 */ |
| reg = (reg_read(REG_DUNIT_CTRL_LOW_ADDR) & 0xFFFFFFE7); |
| dfs_reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); |
| |
| /* Poll Phy lock status register - APLL lock indication - 0x1674 */ |
| do { |
| reg = (reg_read(REG_PHY_LOCK_STATUS_ADDR)) & |
| REG_PHY_LOCK_STATUS_LOCK_MASK; |
| } while (reg != REG_PHY_LOCK_STATUS_LOCK_MASK); /* Wait for '0xFFF' */ |
| |
| reg = (reg_read(REG_SDRAM_CONFIG_ADDR) & REG_SDRAM_CONFIG_MASK); |
| /* [30:29] = 0 - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| reg = reg_read(REG_SDRAM_CONFIG_ADDR) | ~REG_SDRAM_CONFIG_MASK; |
| /* [30:29] = '11' - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| udelay(1000); /* Wait 1msec */ |
| |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) { |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| /* Config CL and CWL with MR0 and MR2 registers */ |
| reg = reg_read(REG_DDR3_MR0_ADDR); |
| reg &= ~0x74; /* CL [3:0]; [6:4],[2] */ |
| reg |= (1 << 5); /* CL = 4, CAS is 6 */ |
| dfs_reg_write(REG_DDR3_MR0_ADDR, reg); |
| reg = REG_SDRAM_OPERATION_CMD_MR0 & |
| ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| reg = reg_read(REG_DDR3_MR2_ADDR); |
| reg &= ~0x38; /* CWL [5:3] */ |
| reg |= (1 << 3); /* CWL = 1, CWL is 6 */ |
| dfs_reg_write(REG_DDR3_MR2_ADDR, reg); |
| |
| reg = REG_SDRAM_OPERATION_CMD_MR2 & |
| ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| /* Set current rd_sample_delay */ |
| reg = reg_read(REG_READ_DATA_SAMPLE_DELAYS_ADDR); |
| reg &= ~(REG_READ_DATA_SAMPLE_DELAYS_MASK << |
| (REG_READ_DATA_SAMPLE_DELAYS_OFFS * cs)); |
| reg |= (5 << (REG_READ_DATA_SAMPLE_DELAYS_OFFS * cs)); |
| dfs_reg_write(REG_READ_DATA_SAMPLE_DELAYS_ADDR, reg); |
| |
| /* Set current rd_ready_delay */ |
| reg = reg_read(REG_READ_DATA_READY_DELAYS_ADDR); |
| reg &= ~(REG_READ_DATA_READY_DELAYS_MASK << |
| (REG_READ_DATA_READY_DELAYS_OFFS * cs)); |
| reg |= ((6) << (REG_READ_DATA_READY_DELAYS_OFFS * cs)); |
| dfs_reg_write(REG_READ_DATA_READY_DELAYS_ADDR, reg); |
| } |
| } |
| |
| /* [2] - DFS Self refresh disable */ |
| reg = reg_read(REG_DFS_ADDR) & ~(1 << REG_DFS_SR_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* [1] - DFS Block enable */ |
| reg = reg_read(REG_DFS_ADDR) & ~(1 << REG_DFS_BLOCK_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Poll DFS Register - 0x1528 [3] - DfsAtSR - |
| * All DRAM devices on all ranks are in self refresh mode - DFS can |
| * be executed afterwards |
| */ |
| do { |
| reg = reg_read(REG_DFS_ADDR) & (1 << REG_DFS_ATSR_OFFS); |
| } while (reg); /* Wait for '1' */ |
| |
| reg = (reg_read(REG_METAL_MASK_ADDR) | (1 << 0)); |
| /* [0] - Enable Dunit to crossbar retry */ |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| /* 0x1600 - PHY lock mask register */ |
| reg = reg_read(REG_ODPG_CNTRL_ADDR); |
| reg &= ~(1 << REG_ODPG_CNTRL_OFFS); /* [21] = 0 */ |
| dfs_reg_write(REG_ODPG_CNTRL_ADDR, reg); |
| |
| /* 0x1670 - PHY lock mask register */ |
| reg = reg_read(REG_PHY_LOCK_MASK_ADDR); |
| reg |= ~REG_PHY_LOCK_MASK_MASK; /* [11:0] = FFF */ |
| dfs_reg_write(REG_PHY_LOCK_MASK_ADDR, reg); |
| |
| DEBUG_DFS_C("DDR3 - DFS - High To Low - Ended successfuly - new Frequency - ", |
| freq, 1); |
| |
| return MV_OK; |
| #endif |
| } |
| |
| /* |
| * Name: ddr3_dfs_low_2_high |
| * Desc: |
| * Args: freq - target frequency |
| * Notes: |
| * Returns: MV_OK - success, MV_FAIL - fail |
| */ |
| int ddr3_dfs_low_2_high(u32 freq, int ratio_2to1, MV_DRAM_INFO *dram_info) |
| { |
| #if defined(MV88F78X60) || defined(MV88F672X) |
| /* This Flow is relevant for ArmadaXP A0 */ |
| u32 reg, freq_par, tmp; |
| u32 cs = 0; |
| |
| DEBUG_DFS_C("DDR3 - DFS - Low To High - Starting DFS procedure to Frequency - ", |
| freq, 1); |
| |
| /* target frequency - freq */ |
| freq_par = ddr3_get_freq_parameter(freq, ratio_2to1); |
| |
| #if defined(MV88F672X) |
| u32 hclk; |
| u32 cpu_freq = ddr3_get_cpu_freq(); |
| get_target_freq(cpu_freq, &tmp, &hclk); |
| #endif |
| |
| /* Configure - DRAM DLL final state after DFS is complete - Enable */ |
| reg = reg_read(REG_DFS_ADDR); |
| /* [0] - DfsDllNextState - Enable */ |
| reg &= ~(1 << REG_DFS_DLLNEXTSTATE_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Configure - XBAR Retry response during Block to enable |
| * internal access - Disable |
| */ |
| reg = reg_read(REG_METAL_MASK_ADDR); |
| /* [0] - RetryMask - Disable */ |
| reg &= ~(1 << REG_METAL_MASK_RETRY_OFFS); |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| /* Configure - Block new external transactions - Enable */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg |= (1 << REG_DFS_BLOCK_OFFS); /* [1] - DfsBlock - Enable */ |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Configure - Move DRAM into Self Refresh */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg |= (1 << REG_DFS_SR_OFFS); /* [2] - DfsSR - Enable */ |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Poll - Wait for Self Refresh indication */ |
| do { |
| reg = ((reg_read(REG_DFS_ADDR)) & (1 << REG_DFS_ATSR_OFFS)); |
| } while (reg == 0x0); /* 0x1528 [3] - DfsAtSR - Wait for '1' */ |
| |
| /* Start of clock change procedure (PLL) */ |
| #if defined(MV88F672X) |
| /* avantaLP */ |
| /* Configure cpupll_clkdiv_reset_mask */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL0); |
| reg &= CPU_PLL_CLOCK_DIVIDER_CNTRL0_MASK; |
| /* 0xE8264[7:0] 0xff CPU Clock Dividers Reset mask */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL0, (reg + 0xFF)); |
| |
| /* Configure cpu_clkdiv_reload_smooth */ |
| reg = reg_read(CPU_PLL_CNTRL0); |
| reg &= CPU_PLL_CNTRL0_RELOAD_SMOOTH_MASK; |
| /* 0xE8260 [15:8] 0x2 CPU Clock Dividers Reload Smooth enable */ |
| dfs_reg_write(CPU_PLL_CNTRL0, |
| reg + (2 << CPU_PLL_CNTRL0_RELOAD_SMOOTH_OFFS)); |
| |
| /* Configure cpupll_clkdiv_relax_en */ |
| reg = reg_read(CPU_PLL_CNTRL0); |
| reg &= CPU_PLL_CNTRL0_RELAX_EN_MASK; |
| /* 0xE8260 [31:24] 0x2 Relax Enable */ |
| dfs_reg_write(CPU_PLL_CNTRL0, |
| reg + (2 << CPU_PLL_CNTRL0_RELAX_EN_OFFS)); |
| |
| /* Configure cpupll_clkdiv_ddr_clk_ratio */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL1); |
| /* |
| * 0xE8268 [13:8] N Set Training clock: |
| * APLL Out Clock (VCO freq) / N = 100 MHz |
| */ |
| reg &= CPU_PLL_CLOCK_DIVIDER_CNTRL1_MASK; |
| reg |= (freq_par << 8); /* full Integer ratio from PLL-out to ddr-clk */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL1, reg); |
| /* Configure cpupll_clkdiv_reload_ratio */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL0); |
| reg &= CPU_PLL_CLOCK_RELOAD_RATIO_MASK; |
| /* 0xE8264 [8]=0x1 CPU Clock Dividers Reload Ratio trigger set */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL0, |
| reg + (1 << CPU_PLL_CLOCK_RELOAD_RATIO_OFFS)); |
| |
| udelay(1); |
| |
| /* Configure cpupll_clkdiv_reload_ratio */ |
| reg = reg_read(CPU_PLL_CLOCK_DIVIDER_CNTRL0); |
| reg &= CPU_PLL_CLOCK_RELOAD_RATIO_MASK; |
| /* 0xE8264 [8]=0x0 CPU Clock Dividers Reload Ratio trigger clear */ |
| dfs_reg_write(CPU_PLL_CLOCK_DIVIDER_CNTRL0, reg); |
| |
| udelay(5); |
| |
| #else |
| /* |
| * Initial Setup - assure that the "load new ratio" is clear (bit 24) |
| * and in the same chance, block reassertions of reset [15:8] |
| * and force reserved bits[7:0]. |
| */ |
| reg = 0x0000FFFF; |
| |
| /* 0x18700 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| /* |
| * RelaX whenever reset is asserted to that channel (good for any case) |
| */ |
| reg = 0x0000FF00; |
| /* 0x18704 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_1_ADDR, reg); |
| |
| reg = reg_read(REG_CPU_DIV_CLK_CTRL_2_ADDR) & |
| REG_CPU_DIV_CLK_CTRL_3_FREQ_MASK; |
| reg |= (freq_par << REG_CPU_DIV_CLK_CTRL_3_FREQ_OFFS); |
| /* full Integer ratio from PLL-out to ddr-clk */ |
| /* 0x1870C - CPU Div CLK control 3 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_2_ADDR, reg); |
| |
| /* |
| * Shut off clock enable to the DDRPHY clock channel (this is the "D"). |
| * All the rest are kept as is (forced, but could be read-modify-write). |
| * This is done now by RMW above. |
| */ |
| reg = 0x000FFF02; |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_4_ADDR, reg); |
| |
| /* Wait before replacing the clock on the DDR Phy Channel. */ |
| udelay(1); |
| |
| reg = 0x0102FDFF; |
| /* |
| * This for triggering the frequency update. Bit[24] is the |
| * central control |
| * bits [23:16] == which channels to change ==2 ==> only DDR Phy |
| * (smooth transition) |
| * bits [15:8] == mask reset reassertion due to clock modification |
| * to these channels. |
| * bits [7:0] == not in use |
| */ |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| udelay(1); |
| |
| /* |
| * Poll Div CLK status 0 register - indication that the clocks |
| * are active - 0x18718 [8] |
| */ |
| do { |
| reg = reg_read(REG_CPU_DIV_CLK_STATUS_0_ADDR) & |
| (1 << REG_CPU_DIV_CLK_ALL_STABLE_OFFS); |
| } while (reg == 0); |
| |
| reg = 0x000000FF; |
| /* |
| * Clean the CTRL0, to be ready for next resets and next requests |
| * of ratio modifications. |
| */ |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| #endif |
| /* End of clock change procedure (PLL) */ |
| |
| if (ratio_2to1) { |
| /* Configure - Select normal clock for the DDR PHY - Disable */ |
| reg = reg_read(REG_DRAM_INIT_CTRL_STATUS_ADDR); |
| /* [16] - ddr_phy_trn_clk_sel - Disable */ |
| reg &= ~(1 << REG_DRAM_INIT_CTRL_TRN_CLK_OFFS); |
| /* 0x18488 - DRAM Init control status register */ |
| dfs_reg_write(REG_DRAM_INIT_CTRL_STATUS_ADDR, reg); |
| } |
| |
| /* |
| * Configure - Set Correct Ratio - according to target ratio |
| * parameter - 2:1/1:1 |
| */ |
| if (ratio_2to1) { |
| /* |
| * [15] - Phy2UnitClkRatio = 1 - Set 2:1 Ratio between |
| * Dunit and Phy |
| */ |
| reg = reg_read(REG_DDR_IO_ADDR) | |
| (1 << REG_DDR_IO_CLK_RATIO_OFFS); |
| } else { |
| /* |
| * [15] - Phy2UnitClkRatio = 0 - Set 1:1 Ratio between |
| * Dunit and Phy |
| */ |
| reg = reg_read(REG_DDR_IO_ADDR) & |
| ~(1 << REG_DDR_IO_CLK_RATIO_OFFS); |
| } |
| dfs_reg_write(REG_DDR_IO_ADDR, reg); /* 0x1524 - DDR IO Register */ |
| |
| /* Configure - 2T Mode - Restore original configuration */ |
| reg = reg_read(REG_DUNIT_CTRL_LOW_ADDR); |
| /* [3:4] 2T - Restore value */ |
| reg &= ~(REG_DUNIT_CTRL_LOW_2T_MASK << REG_DUNIT_CTRL_LOW_2T_OFFS); |
| reg |= ((dram_info->mode_2t & REG_DUNIT_CTRL_LOW_2T_MASK) << |
| REG_DUNIT_CTRL_LOW_2T_OFFS); |
| /* 0x1404 - DDR Controller Control Low Register */ |
| dfs_reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); |
| |
| /* Configure - Restore CL and CWL - MRS Commands */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg &= ~(REG_DFS_CL_NEXT_STATE_MASK << REG_DFS_CL_NEXT_STATE_OFFS); |
| reg &= ~(REG_DFS_CWL_NEXT_STATE_MASK << REG_DFS_CWL_NEXT_STATE_OFFS); |
| |
| if (freq == DDR_400) { |
| if (dram_info->target_frequency == 0x8) |
| tmp = ddr3_cl_to_valid_cl(5); |
| else |
| tmp = ddr3_cl_to_valid_cl(6); |
| } else { |
| tmp = ddr3_cl_to_valid_cl(dram_info->cl); |
| } |
| |
| /* [8] - DfsCLNextState */ |
| reg |= ((tmp & REG_DFS_CL_NEXT_STATE_MASK) << REG_DFS_CL_NEXT_STATE_OFFS); |
| if (freq == DDR_400) { |
| /* [12] - DfsCWLNextState */ |
| reg |= (((0) & REG_DFS_CWL_NEXT_STATE_MASK) << |
| REG_DFS_CWL_NEXT_STATE_OFFS); |
| } else { |
| /* [12] - DfsCWLNextState */ |
| reg |= (((dram_info->cwl) & REG_DFS_CWL_NEXT_STATE_MASK) << |
| REG_DFS_CWL_NEXT_STATE_OFFS); |
| } |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Optional - Configure - DDR3_Rtt_nom_CS# */ |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) { |
| reg = reg_read(REG_DDR3_MR1_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS)); |
| reg &= REG_DDR3_MR1_RTT_MASK; |
| reg |= odt_static[dram_info->cs_ena][cs]; |
| dfs_reg_write(REG_DDR3_MR1_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS), reg); |
| } |
| } |
| |
| /* Configure - Reset ADLLs - Set Reset */ |
| reg = reg_read(REG_DRAM_PHY_CONFIG_ADDR) & REG_DRAM_PHY_CONFIG_MASK; |
| /* [31:30]] - reset pup data ctrl ADLL */ |
| /* 0x15EC - DRAM PHY Config Register */ |
| dfs_reg_write(REG_DRAM_PHY_CONFIG_ADDR, reg); |
| |
| /* Configure - Reset ADLLs - Release Reset */ |
| reg = reg_read(REG_DRAM_PHY_CONFIG_ADDR) | ~REG_DRAM_PHY_CONFIG_MASK; |
| /* [31:30] - normal pup data ctrl ADLL */ |
| /* 0x15EC - DRAM PHY Config register */ |
| dfs_reg_write(REG_DRAM_PHY_CONFIG_ADDR, reg); |
| |
| /* Poll - Wait for APLL + ADLLs lock on new frequency */ |
| do { |
| reg = reg_read(REG_PHY_LOCK_STATUS_ADDR) & |
| REG_PHY_LOCK_APLL_ADLL_STATUS_MASK; |
| /* 0x1674 [10:0] - Phy lock status Register */ |
| } while (reg != REG_PHY_LOCK_APLL_ADLL_STATUS_MASK); |
| |
| /* Configure - Reset the PHY SDR clock divider */ |
| if (ratio_2to1) { |
| /* Pup Reset Divider B - Set Reset */ |
| /* [28] - DataPupRdRST = 0 */ |
| reg = reg_read(REG_SDRAM_CONFIG_ADDR) & |
| ~(1 << REG_SDRAM_CONFIG_PUPRSTDIV_OFFS); |
| /* [28] - DataPupRdRST = 1 */ |
| tmp = reg_read(REG_SDRAM_CONFIG_ADDR) | |
| (1 << REG_SDRAM_CONFIG_PUPRSTDIV_OFFS); |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* Pup Reset Divider B - Release Reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, tmp); |
| } |
| |
| /* Configure - Reset the PHY Read FIFO and Write channels - Set Reset */ |
| reg = reg_read(REG_SDRAM_CONFIG_ADDR) & REG_SDRAM_CONFIG_MASK; |
| /* [30:29] = 0 - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* |
| * Configure - DRAM Data PHY Read [30], Write [29] path reset - |
| * Release Reset |
| */ |
| reg = reg_read(REG_SDRAM_CONFIG_ADDR) | ~REG_SDRAM_CONFIG_MASK; |
| /* [30:29] = '11' - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* Registered DIMM support */ |
| if (dram_info->reg_dimm) { |
| /* |
| * Configure - Change register DRAM operating speed |
| * (DDR3-1333 / DDR3-1600) - CWA_RC |
| */ |
| reg = (0xA & REG_SDRAM_OPERATION_CWA_RC_MASK) << |
| REG_SDRAM_OPERATION_CWA_RC_OFFS; |
| if (freq <= DDR_400) { |
| /* |
| * Configure - Change register DRAM operating speed |
| * (DDR3-800) - CWA_DATA |
| */ |
| reg |= ((0x0 & REG_SDRAM_OPERATION_CWA_DATA_MASK) << |
| REG_SDRAM_OPERATION_CWA_DATA_OFFS); |
| } else if ((freq > DDR_400) && (freq <= DDR_533)) { |
| /* |
| * Configure - Change register DRAM operating speed |
| * (DDR3-1066) - CWA_DATA |
| */ |
| reg |= ((0x1 & REG_SDRAM_OPERATION_CWA_DATA_MASK) << |
| REG_SDRAM_OPERATION_CWA_DATA_OFFS); |
| } else if ((freq > DDR_533) && (freq <= DDR_666)) { |
| /* |
| * Configure - Change register DRAM operating speed |
| * (DDR3-1333) - CWA_DATA |
| */ |
| reg |= ((0x2 & REG_SDRAM_OPERATION_CWA_DATA_MASK) << |
| REG_SDRAM_OPERATION_CWA_DATA_OFFS); |
| } else { |
| /* |
| * Configure - Change register DRAM operating speed |
| * (DDR3-1600) - CWA_DATA |
| */ |
| reg |= ((0x3 & REG_SDRAM_OPERATION_CWA_DATA_MASK) << |
| REG_SDRAM_OPERATION_CWA_DATA_OFFS); |
| } |
| |
| /* Configure - Set Delay - tSTAB */ |
| reg |= (0x1 << REG_SDRAM_OPERATION_CWA_DELAY_SEL_OFFS); |
| /* Configure - Issue CWA command with the above parameters */ |
| reg |= (REG_SDRAM_OPERATION_CMD_CWA & |
| ~(0xF << REG_SDRAM_OPERATION_CS_OFFS)); |
| |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for CWA operation completion */ |
| do { |
| reg = reg_read(REG_SDRAM_OPERATION_ADDR) & |
| REG_SDRAM_OPERATION_CMD_MASK; |
| } while (reg); |
| } |
| |
| /* Configure - Exit Self Refresh */ |
| /* [2] - DfsSR */ |
| reg = reg_read(REG_DFS_ADDR) & ~(1 << REG_DFS_SR_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Poll - DFS Register - 0x1528 [3] - DfsAtSR - All DRAM |
| * devices on all ranks are NOT in self refresh mode |
| */ |
| do { |
| reg = reg_read(REG_DFS_ADDR) & (1 << REG_DFS_ATSR_OFFS); |
| } while (reg); /* Wait for '0' */ |
| |
| /* Configure - Issue Refresh command */ |
| /* [3-0] = 0x2 - Refresh Command, [11-8] - enabled Cs */ |
| reg = REG_SDRAM_OPERATION_CMD_RFRS; |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) |
| reg &= ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| } |
| |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| /* Configure - Block new external transactions - Disable */ |
| reg = reg_read(REG_DFS_ADDR); |
| reg &= ~(1 << REG_DFS_BLOCK_OFFS); /* [1] - DfsBlock - Disable */ |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Configure - XBAR Retry response during Block to enable |
| * internal access - Disable |
| */ |
| reg = reg_read(REG_METAL_MASK_ADDR); |
| /* [0] - RetryMask - Enable */ |
| reg |= (1 << REG_METAL_MASK_RETRY_OFFS); |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) { |
| /* Configure - Set CL */ |
| reg = reg_read(REG_DDR3_MR0_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS)) & |
| ~REG_DDR3_MR0_CL_MASK; |
| if (freq == DDR_400) |
| tmp = ddr3_cl_to_valid_cl(6); |
| else |
| tmp = ddr3_cl_to_valid_cl(dram_info->cl); |
| reg |= ((tmp & 0x1) << REG_DDR3_MR0_CL_OFFS); |
| reg |= ((tmp & 0xE) << REG_DDR3_MR0_CL_HIGH_OFFS); |
| dfs_reg_write(REG_DDR3_MR0_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS), reg); |
| |
| /* Configure - Set CWL */ |
| reg = reg_read(REG_DDR3_MR2_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS)) & |
| ~(REG_DDR3_MR2_CWL_MASK << REG_DDR3_MR2_CWL_OFFS); |
| if (freq == DDR_400) |
| reg |= ((0) << REG_DDR3_MR2_CWL_OFFS); |
| else |
| reg |= ((dram_info->cwl) << REG_DDR3_MR2_CWL_OFFS); |
| dfs_reg_write(REG_DDR3_MR2_CS_ADDR + |
| (cs << MR_CS_ADDR_OFFS), reg); |
| } |
| } |
| |
| DEBUG_DFS_C("DDR3 - DFS - Low To High - Ended successfuly - new Frequency - ", |
| freq, 1); |
| |
| return MV_OK; |
| |
| #else |
| |
| /* This Flow is relevant for Armada370 A0 and ArmadaXP Z1 */ |
| |
| u32 reg, freq_par, tmp; |
| u32 cs = 0; |
| |
| DEBUG_DFS_C("DDR3 - DFS - Low To High - Starting DFS procedure to Frequency - ", |
| freq, 1); |
| |
| /* target frequency - freq */ |
| freq_par = ddr3_get_freq_parameter(freq, ratio_2to1); |
| |
| reg = 0x0000FF00; |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_1_ADDR, reg); |
| |
| /* 0x1600 - PHY lock mask register */ |
| reg = reg_read(REG_ODPG_CNTRL_ADDR); |
| reg |= (1 << REG_ODPG_CNTRL_OFFS); /* [21] = 1 */ |
| dfs_reg_write(REG_ODPG_CNTRL_ADDR, reg); |
| |
| /* 0x1670 - PHY lock mask register */ |
| reg = reg_read(REG_PHY_LOCK_MASK_ADDR); |
| reg &= REG_PHY_LOCK_MASK_MASK; /* [11:0] = 0 */ |
| dfs_reg_write(REG_PHY_LOCK_MASK_ADDR, reg); |
| |
| /* Enable reconfig MR Registers after DFS */ |
| reg = reg_read(REG_DFS_ADDR); /* 0x1528 - DFS register */ |
| /* [4] - Disable - reconfig MR registers after DFS_ERG */ |
| reg &= ~0x11; |
| /* [0] - Enable - DRAM DLL after DFS */ |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Disable DRAM Controller to crossbar retry */ |
| /* [0] - disable */ |
| reg = reg_read(REG_METAL_MASK_ADDR) & ~(1 << 0); |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| /* Enable DRAM Blocking */ |
| /* [1] - DFS Block enable */ |
| reg = reg_read(REG_DFS_ADDR) | (1 << REG_DFS_BLOCK_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Enable Self refresh */ |
| /* [2] - DFS Self refresh enable */ |
| reg = reg_read(REG_DFS_ADDR) | (1 << REG_DFS_SR_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Poll DFS Register - All DRAM devices on all ranks are in |
| * self refresh mode - DFS can be executed afterwards |
| */ |
| /* 0x1528 [3] - DfsAtSR */ |
| do { |
| reg = reg_read(REG_DFS_ADDR) & (1 << REG_DFS_ATSR_OFFS); |
| } while (reg == 0x0); /* Wait for '1' */ |
| |
| /* |
| * Set Correct Ratio - if freq>MARGIN_FREQ use 2:1 ratio |
| * else use 1:1 ratio |
| */ |
| if (ratio_2to1) { |
| /* [15] = 1 - Set 2:1 Ratio between Dunit and Phy */ |
| reg = reg_read(REG_DDR_IO_ADDR) | |
| (1 << REG_DDR_IO_CLK_RATIO_OFFS); |
| } else { |
| /* [15] = 0 - Set 1:1 Ratio between Dunit and Phy */ |
| reg = reg_read(REG_DDR_IO_ADDR) & |
| ~(1 << REG_DDR_IO_CLK_RATIO_OFFS); |
| } |
| dfs_reg_write(REG_DDR_IO_ADDR, reg); /* 0x1524 - DDR IO Register */ |
| |
| /* Switch HCLK Mux from (100Mhz) [16]=0, keep DFS request bit */ |
| reg = 0x20040000; |
| /* |
| * [29] - training logic request DFS, [28:27] - |
| * preload patterns frequency [18] |
| */ |
| |
| /* 0x18488 - DRAM Init control status register */ |
| dfs_reg_write(REG_DRAM_INIT_CTRL_STATUS_ADDR, reg); |
| |
| /* Add delay between entering SR and start ratio modification */ |
| udelay(1); |
| |
| /* |
| * Initial Setup - assure that the "load new ratio" is clear (bit 24) |
| * and in the same chance, block reassertions of reset [15:8] and |
| * force reserved bits[7:0]. |
| */ |
| reg = 0x0000FFFF; |
| /* 0x18700 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| /* |
| * RelaX whenever reset is asserted to that channel (good for any case) |
| */ |
| reg = 0x0000FF00; |
| /* 0x18704 - CPU Div CLK control 0 */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_1_ADDR, reg); |
| |
| reg = reg_read(REG_CPU_DIV_CLK_CTRL_3_ADDR) & |
| REG_CPU_DIV_CLK_CTRL_3_FREQ_MASK; |
| reg |= (freq_par << REG_CPU_DIV_CLK_CTRL_3_FREQ_OFFS); |
| /* Full Integer ratio from PLL-out to ddr-clk */ |
| /* 0x1870C - CPU Div CLK control 3 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_3_ADDR, reg); |
| |
| /* |
| * Shut off clock enable to the DDRPHY clock channel (this is the "D"). |
| * All the rest are kept as is (forced, but could be read-modify-write). |
| * This is done now by RMW above. |
| */ |
| |
| reg = 0x000FFF02; |
| |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_4_ADDR, reg); |
| |
| /* Wait before replacing the clock on the DDR Phy Channel. */ |
| udelay(1); |
| |
| reg = 0x0102FDFF; |
| /* |
| * This for triggering the frequency update. Bit[24] is the |
| * central control |
| * bits [23:16] == which channels to change ==2 ==> only DDR Phy |
| * (smooth transition) |
| * bits [15:8] == mask reset reassertion due to clock modification |
| * to these channels. |
| * bits [7:0] == not in use |
| */ |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| udelay(1); |
| |
| /* |
| * Poll Div CLK status 0 register - indication that the clocks are |
| * active - 0x18718 [8] |
| */ |
| do { |
| reg = reg_read(REG_CPU_DIV_CLK_STATUS_0_ADDR) & |
| (1 << REG_CPU_DIV_CLK_ALL_STABLE_OFFS); |
| } while (reg == 0); |
| |
| reg = 0x000000FF; |
| /* |
| * Clean the CTRL0, to be ready for next resets and next requests of |
| * ratio modifications. |
| */ |
| /* 0x18700 - CPU Div CLK control 0 register */ |
| dfs_reg_write(REG_CPU_DIV_CLK_CTRL_0_ADDR, reg); |
| |
| udelay(5); |
| |
| if (ratio_2to1) { |
| /* Pup Reset Divider B - Set Reset */ |
| /* [28] = 0 - Pup Reset Divider B */ |
| reg = reg_read(REG_SDRAM_CONFIG_ADDR) & ~(1 << 28); |
| /* [28] = 1 - Pup Reset Divider B */ |
| tmp = reg_read(REG_SDRAM_CONFIG_ADDR) | (1 << 28); |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* Pup Reset Divider B - Release Reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, tmp); |
| } |
| |
| /* DRAM Data PHYs ADLL Reset - Set Reset */ |
| reg = (reg_read(REG_DRAM_PHY_CONFIG_ADDR) & REG_DRAM_PHY_CONFIG_MASK); |
| /* [31:30]] - reset pup data ctrl ADLL */ |
| /* 0x15EC - DRAM PHY Config Register */ |
| dfs_reg_write(REG_DRAM_PHY_CONFIG_ADDR, reg); |
| |
| udelay(25); |
| |
| /* APLL lock indication - Poll Phy lock status Register - 0x1674 [9] */ |
| do { |
| reg = reg_read(REG_PHY_LOCK_STATUS_ADDR) & |
| (1 << REG_PHY_LOCK_STATUS_LOCK_OFFS); |
| } while (reg == 0); |
| |
| /* DRAM Data PHYs ADLL Reset - Release Reset */ |
| reg = reg_read(REG_DRAM_PHY_CONFIG_ADDR) | ~REG_DRAM_PHY_CONFIG_MASK; |
| /* [31:30] - normal pup data ctrl ADLL */ |
| /* 0x15EC - DRAM PHY Config register */ |
| dfs_reg_write(REG_DRAM_PHY_CONFIG_ADDR, reg); |
| |
| udelay(10000); /* Wait 10msec */ |
| |
| /* |
| * APLL lock indication - Poll Phy lock status Register - 0x1674 [11:0] |
| */ |
| do { |
| reg = reg_read(REG_PHY_LOCK_STATUS_ADDR) & |
| REG_PHY_LOCK_STATUS_LOCK_MASK; |
| } while (reg != REG_PHY_LOCK_STATUS_LOCK_MASK); |
| |
| /* DRAM Data PHY Read [30], Write [29] path reset - Set Reset */ |
| reg = reg_read(REG_SDRAM_CONFIG_ADDR) & REG_SDRAM_CONFIG_MASK; |
| /* [30:29] = 0 - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* DRAM Data PHY Read [30], Write [29] path reset - Release Reset */ |
| reg = reg_read(REG_SDRAM_CONFIG_ADDR) | ~REG_SDRAM_CONFIG_MASK; |
| /* [30:29] = '11' - Data Pup R/W path reset */ |
| /* 0x1400 - SDRAM Configuration register */ |
| dfs_reg_write(REG_SDRAM_CONFIG_ADDR, reg); |
| |
| /* Disable DFS Reconfig */ |
| reg = reg_read(REG_DFS_ADDR) & ~(1 << 4); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* [2] - DFS Self refresh disable */ |
| reg = reg_read(REG_DFS_ADDR) & ~(1 << REG_DFS_SR_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* |
| * Poll DFS Register - 0x1528 [3] - DfsAtSR - All DRAM devices on |
| * all ranks are NOT in self refresh mode |
| */ |
| do { |
| reg = reg_read(REG_DFS_ADDR) & (1 << REG_DFS_ATSR_OFFS); |
| } while (reg); /* Wait for '0' */ |
| |
| /* 0x1404 */ |
| reg = (reg_read(REG_DUNIT_CTRL_LOW_ADDR) & 0xFFFFFFE7) | 0x2; |
| |
| /* Configure - 2T Mode - Restore original configuration */ |
| /* [3:4] 2T - Restore value */ |
| reg &= ~(REG_DUNIT_CTRL_LOW_2T_MASK << REG_DUNIT_CTRL_LOW_2T_OFFS); |
| reg |= ((dram_info->mode_2t & REG_DUNIT_CTRL_LOW_2T_MASK) << |
| REG_DUNIT_CTRL_LOW_2T_OFFS); |
| dfs_reg_write(REG_DUNIT_CTRL_LOW_ADDR, reg); |
| |
| udelay(1); /* Wait 1us */ |
| |
| for (cs = 0; cs < MAX_CS; cs++) { |
| if (dram_info->cs_ena & (1 << cs)) { |
| reg = (reg_read(REG_DDR3_MR1_ADDR)); |
| /* DLL Enable */ |
| reg &= ~(1 << REG_DDR3_MR1_DLL_ENA_OFFS); |
| dfs_reg_write(REG_DDR3_MR1_ADDR, reg); |
| |
| /* Issue MRS Command to current cs */ |
| reg = REG_SDRAM_OPERATION_CMD_MR1 & |
| ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| /* |
| * [3-0] = 0x4 - MR1 Command, [11-8] - |
| * enable current cs |
| */ |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| /* DLL Reset - MR0 */ |
| reg = reg_read(REG_DDR3_MR0_ADDR); |
| dfs_reg_write(REG_DDR3_MR0_ADDR, reg); |
| |
| /* Issue MRS Command to current cs */ |
| reg = REG_SDRAM_OPERATION_CMD_MR0 & |
| ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| /* |
| * [3-0] = 0x4 - MR1 Command, [11-8] - |
| * enable current cs |
| */ |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| reg = reg_read(REG_DDR3_MR0_ADDR); |
| reg &= ~0x74; /* CL [3:0]; [6:4],[2] */ |
| |
| if (freq == DDR_400) |
| tmp = ddr3_cl_to_valid_cl(6) & 0xF; |
| else |
| tmp = ddr3_cl_to_valid_cl(dram_info->cl) & 0xF; |
| |
| reg |= ((tmp & 0x1) << 2); |
| reg |= ((tmp >> 1) << 4); /* to bit 4 */ |
| dfs_reg_write(REG_DDR3_MR0_ADDR, reg); |
| |
| reg = REG_SDRAM_OPERATION_CMD_MR0 & |
| ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| reg = reg_read(REG_DDR3_MR2_ADDR); |
| reg &= ~0x38; /* CWL [5:3] */ |
| /* CWL = 0 ,for 400 MHg is 5 */ |
| if (freq != DDR_400) |
| reg |= dram_info->cwl << REG_DDR3_MR2_CWL_OFFS; |
| dfs_reg_write(REG_DDR3_MR2_ADDR, reg); |
| reg = REG_SDRAM_OPERATION_CMD_MR2 & |
| ~(1 << (REG_SDRAM_OPERATION_CS_OFFS + cs)); |
| /* 0x1418 - SDRAM Operation Register */ |
| dfs_reg_write(REG_SDRAM_OPERATION_ADDR, reg); |
| |
| /* Poll - Wait for Refresh operation completion */ |
| wait_refresh_op_complete(); |
| |
| /* Set current rd_sample_delay */ |
| reg = reg_read(REG_READ_DATA_SAMPLE_DELAYS_ADDR); |
| reg &= ~(REG_READ_DATA_SAMPLE_DELAYS_MASK << |
| (REG_READ_DATA_SAMPLE_DELAYS_OFFS * cs)); |
| reg |= (dram_info->cl << |
| (REG_READ_DATA_SAMPLE_DELAYS_OFFS * cs)); |
| dfs_reg_write(REG_READ_DATA_SAMPLE_DELAYS_ADDR, reg); |
| |
| /* Set current rd_ready_delay */ |
| reg = reg_read(REG_READ_DATA_READY_DELAYS_ADDR); |
| reg &= ~(REG_READ_DATA_READY_DELAYS_MASK << |
| (REG_READ_DATA_READY_DELAYS_OFFS * cs)); |
| reg |= ((dram_info->cl + 1) << |
| (REG_READ_DATA_SAMPLE_DELAYS_OFFS * cs)); |
| dfs_reg_write(REG_READ_DATA_READY_DELAYS_ADDR, reg); |
| } |
| } |
| |
| /* Enable ODT on DLL-on mode */ |
| dfs_reg_write(REG_SDRAM_ODT_CTRL_HIGH_ADDR, 0); |
| |
| /* [1] - DFS Block disable */ |
| reg = reg_read(REG_DFS_ADDR) & ~(1 << REG_DFS_BLOCK_OFFS); |
| dfs_reg_write(REG_DFS_ADDR, reg); /* 0x1528 - DFS register */ |
| |
| /* Change DDR frequency to 100MHz procedure: */ |
| /* 0x1600 - PHY lock mask register */ |
| reg = reg_read(REG_ODPG_CNTRL_ADDR); |
| reg &= ~(1 << REG_ODPG_CNTRL_OFFS); /* [21] = 0 */ |
| dfs_reg_write(REG_ODPG_CNTRL_ADDR, reg); |
| |
| /* Change DDR frequency to 100MHz procedure: */ |
| /* 0x1670 - PHY lock mask register */ |
| reg = reg_read(REG_PHY_LOCK_MASK_ADDR); |
| reg |= ~REG_PHY_LOCK_MASK_MASK; /* [11:0] = FFF */ |
| dfs_reg_write(REG_PHY_LOCK_MASK_ADDR, reg); |
| |
| reg = reg_read(REG_METAL_MASK_ADDR) | (1 << 0); /* [0] - disable */ |
| /* 0x14B0 - Dunit MMask Register */ |
| dfs_reg_write(REG_METAL_MASK_ADDR, reg); |
| |
| DEBUG_DFS_C("DDR3 - DFS - Low To High - Ended successfuly - new Frequency - ", |
| freq, 1); |
| return MV_OK; |
| #endif |
| } |