| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright (C) 2006 Freescale Semiconductor, Inc. |
| * Dave Liu <daveliu@freescale.com> |
| * |
| * Copyright (C) 2007 Logic Product Development, Inc. |
| * Peter Barada <peterb@logicpd.com> |
| * |
| * Copyright (C) 2007 MontaVista Software, Inc. |
| * Anton Vorontsov <avorontsov@ru.mvista.com> |
| * |
| * (C) Copyright 2010 |
| * Heiko Schocher, DENX Software Engineering, hs@denx.de. |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| |
| #define CONFIG_HOSTNAME "kmvect1" |
| #define CONFIG_KM_BOARD_NAME "kmvect1" |
| /* at end of uboot partition, before env */ |
| #define CONFIG_SYS_QE_FW_ADDR 0xF00B0000 |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_E300 1 /* E300 family */ |
| #define CONFIG_QE 1 /* Has QE */ |
| |
| #define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" |
| |
| /* include common defines/options for all Keymile boards */ |
| #include "km/keymile-common.h" |
| #include "km/km-powerpc.h" |
| |
| /* |
| * System Clock Setup |
| */ |
| #define CONFIG_83XX_CLKIN 66000000 |
| #define CONFIG_SYS_CLK_FREQ 66000000 |
| #define CONFIG_83XX_PCICLK 66000000 |
| |
| /* |
| * IMMR new address |
| */ |
| #define CONFIG_SYS_IMMR 0xE0000000 |
| |
| /* |
| * Bus Arbitration Configuration Register (ACR) |
| */ |
| #define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */ |
| #define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */ |
| #define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */ |
| #define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */ |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ |
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| |
| #define CFG_83XX_DDR_USES_CS0 |
| |
| /* |
| * Manually set up DDR parameters |
| */ |
| #define CONFIG_DDR_II |
| #define CONFIG_SYS_DDR_SIZE 2048 /* MB */ |
| |
| /* |
| * The reserved memory |
| */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #define CONFIG_SYS_FLASH_BASE 0xF0000000 |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| /* Reserve 768 kB for Mon */ |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| |
| /* |
| * Initial RAM Base Address Setup |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| |
| /* |
| * Init Local Bus Memory Controller: |
| * |
| * Bank Bus Machine PortSz Size Device |
| * ---- --- ------- ------ ----- ------ |
| * 0 Local GPCM 16 bit 256MB FLASH |
| * 1 Local GPCM 8 bit 128MB GPIO/PIGGY |
| * |
| */ |
| /* |
| * FLASH on the Local Bus |
| */ |
| #define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ |
| |
| #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_256MB) |
| |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ |
| BR_PS_16 | /* 16 bit port size */ \ |
| BR_MS_GPCM | /* MSEL = GPCM */ \ |
| BR_V) |
| |
| #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_5 | \ |
| OR_GPCM_TRLX_SET | OR_GPCM_EAD) |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| |
| /* |
| * PRIO1/PIGGY on the local bus CS1 |
| */ |
| /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_KMBEC_FPGA_BASE |
| #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_128MB) |
| |
| #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_KMBEC_FPGA_BASE | \ |
| BR_PS_8 | /* 8 bit port size */ \ |
| BR_MS_GPCM | /* MSEL = GPCM */ \ |
| BR_V) |
| #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_KMBEC_FPGA_SIZE) | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_2 | \ |
| OR_GPCM_TRLX_SET | OR_GPCM_EAD) |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) |
| |
| /* |
| * QE UEC ethernet configuration |
| */ |
| #define CONFIG_UEC_ETH |
| #define CONFIG_ETHPRIME "UEC0" |
| |
| #ifdef CONFIG_UEC_ETH1 |
| #define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ |
| #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 |
| #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR 0 |
| #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII |
| #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 |
| #endif |
| |
| /* |
| * Environment |
| */ |
| |
| #ifndef CONFIG_SYS_RAMBOOT |
| #ifndef CONFIG_ENV_ADDR |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ |
| CONFIG_SYS_MONITOR_LEN) |
| #endif |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ |
| #ifndef CONFIG_ENV_OFFSET |
| #define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) |
| #endif |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ |
| CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| |
| #else /* CFG_SYS_RAMBOOT */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif /* CFG_SYS_RAMBOOT */ |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_NUM_I2C_BUSES 4 |
| #define CONFIG_SYS_I2C_MAX_HOPS 1 |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 200000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_FSL_I2C2_SPEED 200000 |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 |
| #define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ |
| {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ |
| {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ |
| {1, {I2C_NULL_HOP} } } |
| |
| #define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ |
| |
| #if defined(CONFIG_CMD_NAND) |
| #define CONFIG_NAND_KMETER1 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE |
| #endif |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) |
| |
| /* |
| * Core HID Setup |
| */ |
| #define CONFIG_SYS_HID0_INIT 0x000000000 |
| #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ |
| HID0_ENABLE_INSTRUCTION_CACHE) |
| #define CONFIG_SYS_HID2 HID2_HBE |
| |
| /* |
| * Internal Definitions |
| */ |
| #define BOOTFLASH_START 0xF0000000 |
| |
| #define CONFIG_KM_CONSOLE_TTY "ttyS0" |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ENV_OVERWRITE |
| #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ |
| #define CONFIG_KM_DEF_ENV "km-common=empty\0" |
| #endif |
| |
| #ifndef CONFIG_KM_DEF_ARCH |
| #define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" |
| #endif |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_KM_DEF_ENV \ |
| CONFIG_KM_DEF_ARCH \ |
| "newenv=" \ |
| "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ |
| "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ |
| "unlock=yes\0" \ |
| "" |
| |
| #if defined(CONFIG_UEC_ETH) |
| #define CONFIG_HAS_ETH0 |
| #endif |
| |
| /* QE microcode/firmware address */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NOR |
| /* between the u-boot partition and env */ |
| #ifndef CONFIG_SYS_QE_FW_ADDR |
| #define CONFIG_SYS_QE_FW_ADDR 0xF00C0000 |
| #endif |
| |
| /* |
| * System IO Config |
| */ |
| /* 0x14000180 SICR_1 */ |
| #define CONFIG_SYS_SICRL (0 \ |
| | SICR_1_UART1_UART1RTS \ |
| | SICR_1_I2C_CKSTOP \ |
| | SICR_1_IRQ_A_IRQ \ |
| | SICR_1_IRQ_B_IRQ \ |
| | SICR_1_GPIO_A_GPIO \ |
| | SICR_1_GPIO_B_GPIO \ |
| | SICR_1_GPIO_C_GPIO \ |
| | SICR_1_GPIO_D_GPIO \ |
| | SICR_1_GPIO_E_GPIO \ |
| | SICR_1_GPIO_F_GPIO \ |
| | SICR_1_USB_A_UART2S \ |
| | SICR_1_USB_B_UART2RTS \ |
| | SICR_1_FEC1_FEC1 \ |
| | SICR_1_FEC2_FEC2 \ |
| ) |
| |
| /* 0x00080400 SICR_2 */ |
| #define CONFIG_SYS_SICRH (0 \ |
| | SICR_2_FEC3_FEC3 \ |
| | SICR_2_HDLC1_A_HDLC1 \ |
| | SICR_2_ELBC_A_LA \ |
| | SICR_2_ELBC_B_LCLK \ |
| | SICR_2_HDLC2_A_HDLC2 \ |
| | SICR_2_USB_D_GPIO \ |
| | SICR_2_PCI_PCI \ |
| | SICR_2_HDLC1_B_HDLC1 \ |
| | SICR_2_HDLC1_C_HDLC1 \ |
| | SICR_2_HDLC2_B_GPIO \ |
| | SICR_2_HDLC2_C_HDLC2 \ |
| | SICR_2_QUIESCE_B \ |
| ) |
| |
| /* GPR_1 */ |
| #define CONFIG_SYS_GPR1 0x50008060 |
| |
| #define CONFIG_SYS_GP1DIR 0x00000000 |
| #define CONFIG_SYS_GP1ODR 0x00000000 |
| #define CONFIG_SYS_GP2DIR 0xFF000000 |
| #define CONFIG_SYS_GP2ODR 0x00000000 |
| |
| #define CONFIG_SYS_DDRCDR (\ |
| DDRCDR_EN | \ |
| DDRCDR_PZ_MAXZ | \ |
| DDRCDR_NZ_MAXZ | \ |
| DDRCDR_M_ODR) |
| |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f |
| #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ |
| SDRAM_CFG_32_BE | \ |
| SDRAM_CFG_SREN | \ |
| SDRAM_CFG_HSE) |
| |
| #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 |
| #define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| #define CONFIG_SYS_DDR_INTERVAL ((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ |
| (0x200 << SDRAM_INTERVAL_REFINT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ |
| CSCONFIG_ODT_RD_NEVER | \ |
| CSCONFIG_ODT_WR_ONLY_CURRENT | \ |
| CSCONFIG_ROW_BIT_13 | \ |
| CSCONFIG_COL_BIT_10) |
| |
| #define CONFIG_SYS_DDR_MODE 0x47860242 |
| #define CONFIG_SYS_DDR_MODE2 0x8080c000 |
| |
| #define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ |
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ |
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ |
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ |
| (0 << TIMING_CFG0_WWT_SHIFT) | \ |
| (0 << TIMING_CFG0_RRT_SHIFT) | \ |
| (0 << TIMING_CFG0_WRT_SHIFT) | \ |
| (0 << TIMING_CFG0_RWT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_40) | \ |
| (2 << TIMING_CFG1_WRTORD_SHIFT) | \ |
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ |
| (3 << TIMING_CFG1_WRREC_SHIFT) | \ |
| (7 << TIMING_CFG1_REFREC_SHIFT) | \ |
| (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ |
| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ |
| (3 << TIMING_CFG1_PRETOACT_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ |
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ |
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ |
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ |
| (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ |
| (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ |
| (5 << TIMING_CFG2_CPO_SHIFT)) |
| |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| |
| #define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000 |
| #define CONFIG_SYS_KMBEC_FPGA_SIZE 128 |
| |
| /* EEprom support */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| |
| /* |
| * Local Bus Configuration & Clock Setup |
| */ |
| #define CONFIG_SYS_LCRR_DBYP 0x80000000 |
| #define CONFIG_SYS_LCRR_EADC 0x00010000 |
| #define CONFIG_SYS_LCRR_CLKDIV 0x00000002 |
| |
| #define CONFIG_SYS_LBC_LBCR 0x00000000 |
| |
| #define CONFIG_SYS_APP1_BASE 0xA0000000 |
| #define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */ |
| #define CONFIG_SYS_APP2_BASE 0xB0000000 |
| #define CONFIG_SYS_APP2_SIZE 256 /* Megabytes */ |
| |
| /* EEprom support */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| |
| /* |
| * Init Local Bus Memory Controller: |
| * |
| * Bank Bus Machine PortSz Size Device |
| * ---- --- ------- ------ ----- ------ |
| * 2 Local UPMA 16 bit 256MB APP1 |
| * 3 Local GPCM 16 bit 256MB APP2 |
| * |
| */ |
| |
| /* |
| * APP1 on the local bus CS2 |
| */ |
| #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_APP1_BASE |
| #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_256MB) |
| |
| #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_APP1_BASE | \ |
| BR_PS_16 | \ |
| BR_MS_UPMA | \ |
| BR_V) |
| #define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_APP1_SIZE)) |
| |
| #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_APP2_BASE | \ |
| BR_PS_16 | \ |
| BR_V) |
| |
| #define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \ |
| OR_GPCM_CSNT | \ |
| OR_GPCM_ACS_DIV4 | \ |
| OR_GPCM_SCY_3 | \ |
| OR_GPCM_TRLX_SET) |
| |
| #define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \ |
| 0x0000c000 | \ |
| MxMR_WLFx_2X) |
| |
| #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_APP2_BASE |
| #define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_256MB) |
| |
| /* |
| * QE UEC ethernet configuration |
| */ |
| #define CONFIG_MV88E6352_SWITCH |
| #define CONFIG_KM_MVEXTSW_ADDR 0x10 |
| |
| /* ethernet port connected to simple switch 88e6122 (UEC0) */ |
| #define CONFIG_UEC_ETH1 |
| #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ |
| #define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 |
| |
| #define CONFIG_FIXED_PHY 0xFFFFFFFF |
| #define CONFIG_SYS_FIXED_PHY_ADDR 0x1E /* unused address */ |
| #define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \ |
| {devnum, speed, duplex} |
| #define CONFIG_SYS_FIXED_PHY_PORTS \ |
| CONFIG_SYS_FIXED_PHY_PORT("UEC0", SPEED_100, DUPLEX_FULL) |
| |
| #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR CONFIG_SYS_FIXED_PHY_ADDR |
| #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII |
| #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 |
| |
| /* ethernet port connected to piggy (UEC2) */ |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_UEC_ETH2 |
| #define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */ |
| #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ |
| #define CONFIG_SYS_UEC2_TX_CLK QE_CLK12 |
| #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC2_PHY_ADDR 0 |
| #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII |
| #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 |
| |
| #endif /* __CONFIG_H */ |