| /* |
| * Copyright (C) 2010-2013 Freescale Semiconductor, Inc. |
| * Copyright (C) 2013, Boundary Devices <info@boundarydevices.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <asm/io.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/arch/iomux.h> |
| #include <asm/arch/sys_proto.h> |
| #include <malloc.h> |
| #include <asm/arch/mx6-pins.h> |
| #include <asm/errno.h> |
| #include <asm/gpio.h> |
| #include <asm/imx-common/iomux-v3.h> |
| #include <asm/imx-common/mxc_i2c.h> |
| #include <asm/imx-common/sata.h> |
| #include <asm/imx-common/spi.h> |
| #include <asm/imx-common/boot_mode.h> |
| #include <asm/imx-common/video.h> |
| #include <mmc.h> |
| #include <fsl_esdhc.h> |
| #include <micrel.h> |
| #include <miiphy.h> |
| #include <netdev.h> |
| #include <asm/arch/crm_regs.h> |
| #include <asm/arch/mxc_hdmi.h> |
| #include <i2c.h> |
| #include <input.h> |
| #include <netdev.h> |
| #include <usb/ehci-fsl.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| #define GP_USB_OTG_PWR IMX_GPIO_NR(3, 22) |
| |
| #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ |
| PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ |
| PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ |
| PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) |
| |
| #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ |
| PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) |
| |
| #define BUTTON_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) |
| |
| #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ |
| PAD_CTL_ODE | PAD_CTL_SRE_FAST) |
| |
| #define WEAK_PULLUP (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ |
| PAD_CTL_SRE_SLOW) |
| |
| #define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ |
| PAD_CTL_HYS | PAD_CTL_SRE_SLOW) |
| |
| #define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm) |
| |
| int dram_init(void) |
| { |
| gd->ram_size = ((ulong)CONFIG_DDR_MB * 1024 * 1024); |
| |
| return 0; |
| } |
| |
| static iomux_v3_cfg_t const uart1_pads[] = { |
| MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| }; |
| |
| static iomux_v3_cfg_t const uart2_pads[] = { |
| MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), |
| }; |
| |
| #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) |
| |
| /* I2C1, SGTL5000 */ |
| static struct i2c_pads_info i2c_pad_info0 = { |
| .scl = { |
| .i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC, |
| .gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC, |
| .gp = IMX_GPIO_NR(3, 21) |
| }, |
| .sda = { |
| .i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC, |
| .gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC, |
| .gp = IMX_GPIO_NR(3, 28) |
| } |
| }; |
| |
| /* I2C2 Camera, MIPI */ |
| static struct i2c_pads_info i2c_pad_info1 = { |
| .scl = { |
| .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC, |
| .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC, |
| .gp = IMX_GPIO_NR(4, 12) |
| }, |
| .sda = { |
| .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC, |
| .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC, |
| .gp = IMX_GPIO_NR(4, 13) |
| } |
| }; |
| |
| /* I2C3, J15 - RGB connector */ |
| static struct i2c_pads_info i2c_pad_info2 = { |
| .scl = { |
| .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC, |
| .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC, |
| .gp = IMX_GPIO_NR(1, 5) |
| }, |
| .sda = { |
| .i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | PC, |
| .gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | PC, |
| .gp = IMX_GPIO_NR(7, 11) |
| } |
| }; |
| |
| static iomux_v3_cfg_t const usdhc2_pads[] = { |
| MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| }; |
| |
| static iomux_v3_cfg_t const usdhc3_pads[] = { |
| MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ |
| }; |
| |
| static iomux_v3_cfg_t const usdhc4_pads[] = { |
| MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), |
| MX6_PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ |
| }; |
| |
| static iomux_v3_cfg_t const enet_pads1[] = { |
| MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| /* pin 35 - 1 (PHY_AD2) on reset */ |
| MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| /* pin 32 - 1 - (MODE0) all */ |
| MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| /* pin 31 - 1 - (MODE1) all */ |
| MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| /* pin 28 - 1 - (MODE2) all */ |
| MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| /* pin 27 - 1 - (MODE3) all */ |
| MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ |
| MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| /* pin 42 PHY nRST */ |
| MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| }; |
| |
| static iomux_v3_cfg_t const enet_pads2[] = { |
| MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), |
| }; |
| |
| static iomux_v3_cfg_t const misc_pads[] = { |
| MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(WEAK_PULLUP), |
| MX6_PAD_KEY_COL4__USB_OTG_OC | MUX_PAD_CTRL(WEAK_PULLUP), |
| MX6_PAD_EIM_D30__USB_H1_OC | MUX_PAD_CTRL(WEAK_PULLUP), |
| /* OTG Power enable */ |
| MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(OUTPUT_40OHM), |
| }; |
| |
| /* wl1271 pads on nitrogen6x */ |
| static iomux_v3_cfg_t const wl12xx_pads[] = { |
| (MX6_PAD_NANDF_CS1__GPIO6_IO14 & ~MUX_PAD_CTRL_MASK) |
| | MUX_PAD_CTRL(WEAK_PULLDOWN), |
| (MX6_PAD_NANDF_CS2__GPIO6_IO15 & ~MUX_PAD_CTRL_MASK) |
| | MUX_PAD_CTRL(OUTPUT_40OHM), |
| (MX6_PAD_NANDF_CS3__GPIO6_IO16 & ~MUX_PAD_CTRL_MASK) |
| | MUX_PAD_CTRL(OUTPUT_40OHM), |
| }; |
| #define WL12XX_WL_IRQ_GP IMX_GPIO_NR(6, 14) |
| #define WL12XX_WL_ENABLE_GP IMX_GPIO_NR(6, 15) |
| #define WL12XX_BT_ENABLE_GP IMX_GPIO_NR(6, 16) |
| |
| /* Button assignments for J14 */ |
| static iomux_v3_cfg_t const button_pads[] = { |
| /* Menu */ |
| MX6_PAD_NANDF_D1__GPIO2_IO01 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), |
| /* Back */ |
| MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), |
| /* Labelled Search (mapped to Power under Android) */ |
| MX6_PAD_NANDF_D3__GPIO2_IO03 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), |
| /* Home */ |
| MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), |
| /* Volume Down */ |
| MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), |
| /* Volume Up */ |
| MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), |
| }; |
| |
| static void setup_iomux_enet(void) |
| { |
| gpio_direction_output(IMX_GPIO_NR(3, 23), 0); /* SABRE Lite PHY rst */ |
| gpio_direction_output(IMX_GPIO_NR(1, 27), 0); /* Nitrogen6X PHY rst */ |
| gpio_direction_output(IMX_GPIO_NR(6, 30), 1); |
| gpio_direction_output(IMX_GPIO_NR(6, 25), 1); |
| gpio_direction_output(IMX_GPIO_NR(6, 27), 1); |
| gpio_direction_output(IMX_GPIO_NR(6, 28), 1); |
| gpio_direction_output(IMX_GPIO_NR(6, 29), 1); |
| imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1)); |
| gpio_direction_output(IMX_GPIO_NR(6, 24), 1); |
| |
| /* Need delay 10ms according to KSZ9021 spec */ |
| udelay(1000 * 10); |
| gpio_set_value(IMX_GPIO_NR(3, 23), 1); /* SABRE Lite PHY reset */ |
| gpio_set_value(IMX_GPIO_NR(1, 27), 1); /* Nitrogen6X PHY reset */ |
| |
| imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2)); |
| udelay(100); /* Wait 100 us before using mii interface */ |
| } |
| |
| static iomux_v3_cfg_t const usb_pads[] = { |
| MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| }; |
| |
| static void setup_iomux_uart(void) |
| { |
| imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); |
| imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); |
| } |
| |
| #ifdef CONFIG_USB_EHCI_MX6 |
| int board_ehci_hcd_init(int port) |
| { |
| imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); |
| |
| /* Reset USB hub */ |
| gpio_direction_output(IMX_GPIO_NR(7, 12), 0); |
| mdelay(2); |
| gpio_set_value(IMX_GPIO_NR(7, 12), 1); |
| |
| return 0; |
| } |
| |
| int board_ehci_power(int port, int on) |
| { |
| if (port) |
| return 0; |
| gpio_set_value(GP_USB_OTG_PWR, on); |
| return 0; |
| } |
| |
| #endif |
| |
| #ifdef CONFIG_FSL_ESDHC |
| static struct fsl_esdhc_cfg usdhc_cfg[2] = { |
| {USDHC3_BASE_ADDR}, |
| {USDHC4_BASE_ADDR}, |
| }; |
| |
| int board_mmc_getcd(struct mmc *mmc) |
| { |
| struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; |
| int gp_cd = (cfg->esdhc_base == USDHC3_BASE_ADDR) ? IMX_GPIO_NR(7, 0) : |
| IMX_GPIO_NR(2, 6); |
| |
| gpio_direction_input(gp_cd); |
| return !gpio_get_value(gp_cd); |
| } |
| |
| int board_mmc_init(bd_t *bis) |
| { |
| int ret; |
| u32 index = 0; |
| |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); |
| usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); |
| |
| usdhc_cfg[0].max_bus_width = 4; |
| usdhc_cfg[1].max_bus_width = 4; |
| |
| for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { |
| switch (index) { |
| case 0: |
| imx_iomux_v3_setup_multiple_pads( |
| usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); |
| break; |
| case 1: |
| imx_iomux_v3_setup_multiple_pads( |
| usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); |
| break; |
| default: |
| printf("Warning: you configured more USDHC controllers" |
| "(%d) then supported by the board (%d)\n", |
| index + 1, CONFIG_SYS_FSL_USDHC_NUM); |
| return -EINVAL; |
| } |
| |
| ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_MXC_SPI |
| int board_spi_cs_gpio(unsigned bus, unsigned cs) |
| { |
| return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1; |
| } |
| |
| static iomux_v3_cfg_t const ecspi1_pads[] = { |
| /* SS1 */ |
| MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), |
| MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), |
| MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), |
| }; |
| |
| static void setup_spi(void) |
| { |
| imx_iomux_v3_setup_multiple_pads(ecspi1_pads, |
| ARRAY_SIZE(ecspi1_pads)); |
| } |
| #endif |
| |
| int board_phy_config(struct phy_device *phydev) |
| { |
| /* min rx data delay */ |
| ksz9021_phy_extended_write(phydev, |
| MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, 0x0); |
| /* min tx data delay */ |
| ksz9021_phy_extended_write(phydev, |
| MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW, 0x0); |
| /* max rx/tx clock delay, min rx/tx control */ |
| ksz9021_phy_extended_write(phydev, |
| MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0xf0f0); |
| if (phydev->drv->config) |
| phydev->drv->config(phydev); |
| |
| return 0; |
| } |
| |
| int board_eth_init(bd_t *bis) |
| { |
| uint32_t base = IMX_FEC_BASE; |
| struct mii_dev *bus = NULL; |
| struct phy_device *phydev = NULL; |
| int ret; |
| |
| setup_iomux_enet(); |
| |
| #ifdef CONFIG_FEC_MXC |
| bus = fec_get_miibus(base, -1); |
| if (!bus) |
| return 0; |
| /* scan phy 4,5,6,7 */ |
| phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII); |
| if (!phydev) { |
| free(bus); |
| return 0; |
| } |
| printf("using phy at %d\n", phydev->addr); |
| ret = fec_probe(bis, -1, base, bus, phydev); |
| if (ret) { |
| printf("FEC MXC: %s:failed\n", __func__); |
| free(phydev); |
| free(bus); |
| } |
| #endif |
| |
| #ifdef CONFIG_CI_UDC |
| /* For otg ethernet*/ |
| usb_eth_initialize(bis); |
| #endif |
| return 0; |
| } |
| |
| static void setup_buttons(void) |
| { |
| imx_iomux_v3_setup_multiple_pads(button_pads, |
| ARRAY_SIZE(button_pads)); |
| } |
| |
| #if defined(CONFIG_VIDEO_IPUV3) |
| |
| static iomux_v3_cfg_t const backlight_pads[] = { |
| /* Backlight on RGB connector: J15 */ |
| MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| #define RGB_BACKLIGHT_GP IMX_GPIO_NR(1, 21) |
| |
| /* Backlight on LVDS connector: J6 */ |
| MX6_PAD_SD1_CMD__GPIO1_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL), |
| #define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 18) |
| }; |
| |
| static iomux_v3_cfg_t const rgb_pads[] = { |
| MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK, |
| MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, |
| MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, |
| MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, |
| MX6_PAD_DI0_PIN4__GPIO4_IO20, |
| MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00, |
| MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01, |
| MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02, |
| MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03, |
| MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04, |
| MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05, |
| MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06, |
| MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07, |
| MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08, |
| MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09, |
| MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10, |
| MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11, |
| MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12, |
| MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13, |
| MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14, |
| MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15, |
| MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16, |
| MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17, |
| MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18, |
| MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19, |
| MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20, |
| MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21, |
| MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22, |
| MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23, |
| }; |
| |
| static void do_enable_hdmi(struct display_info_t const *dev) |
| { |
| imx_enable_hdmi_phy(); |
| } |
| |
| static int detect_i2c(struct display_info_t const *dev) |
| { |
| return ((0 == i2c_set_bus_num(dev->bus)) |
| && |
| (0 == i2c_probe(dev->addr))); |
| } |
| |
| static void enable_lvds(struct display_info_t const *dev) |
| { |
| struct iomuxc *iomux = (struct iomuxc *) |
| IOMUXC_BASE_ADDR; |
| u32 reg = readl(&iomux->gpr[2]); |
| reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT; |
| writel(reg, &iomux->gpr[2]); |
| gpio_direction_output(LVDS_BACKLIGHT_GP, 1); |
| } |
| |
| static void enable_lvds_jeida(struct display_info_t const *dev) |
| { |
| struct iomuxc *iomux = (struct iomuxc *) |
| IOMUXC_BASE_ADDR; |
| u32 reg = readl(&iomux->gpr[2]); |
| reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
| |IOMUXC_GPR2_BIT_MAPPING_CH0_JEIDA; |
| writel(reg, &iomux->gpr[2]); |
| gpio_direction_output(LVDS_BACKLIGHT_GP, 1); |
| } |
| |
| static void enable_rgb(struct display_info_t const *dev) |
| { |
| imx_iomux_v3_setup_multiple_pads( |
| rgb_pads, |
| ARRAY_SIZE(rgb_pads)); |
| gpio_direction_output(RGB_BACKLIGHT_GP, 1); |
| } |
| |
| struct display_info_t const displays[] = {{ |
| .bus = 1, |
| .addr = 0x50, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .detect = detect_i2c, |
| .enable = do_enable_hdmi, |
| .mode = { |
| .name = "HDMI", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 768, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 0, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .detect = NULL, |
| .enable = enable_lvds_jeida, |
| .mode = { |
| .name = "LDB-WXGA", |
| .refresh = 60, |
| .xres = 1280, |
| .yres = 800, |
| .pixclock = 14065, |
| .left_margin = 40, |
| .right_margin = 40, |
| .upper_margin = 3, |
| .lower_margin = 80, |
| .hsync_len = 10, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 0, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .detect = NULL, |
| .enable = enable_lvds, |
| .mode = { |
| .name = "LDB-WXGA-S", |
| .refresh = 60, |
| .xres = 1280, |
| .yres = 800, |
| .pixclock = 14065, |
| .left_margin = 40, |
| .right_margin = 40, |
| .upper_margin = 3, |
| .lower_margin = 80, |
| .hsync_len = 10, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 2, |
| .addr = 0x4, |
| .pixfmt = IPU_PIX_FMT_LVDS666, |
| .detect = detect_i2c, |
| .enable = enable_lvds, |
| .mode = { |
| .name = "Hannstar-XGA", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 768, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 0, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_LVDS666, |
| .detect = NULL, |
| .enable = enable_lvds, |
| .mode = { |
| .name = "LG-9.7", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 768, |
| .pixclock = 15385, /* ~65MHz */ |
| .left_margin = 480, |
| .right_margin = 260, |
| .upper_margin = 16, |
| .lower_margin = 6, |
| .hsync_len = 250, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 2, |
| .addr = 0x38, |
| .pixfmt = IPU_PIX_FMT_LVDS666, |
| .detect = detect_i2c, |
| .enable = enable_lvds, |
| .mode = { |
| .name = "wsvga-lvds", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 600, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 2, |
| .addr = 0x10, |
| .pixfmt = IPU_PIX_FMT_RGB666, |
| .detect = detect_i2c, |
| .enable = enable_rgb, |
| .mode = { |
| .name = "fusion7", |
| .refresh = 60, |
| .xres = 800, |
| .yres = 480, |
| .pixclock = 33898, |
| .left_margin = 96, |
| .right_margin = 24, |
| .upper_margin = 3, |
| .lower_margin = 10, |
| .hsync_len = 72, |
| .vsync_len = 7, |
| .sync = 0x40000002, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 0, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_RGB666, |
| .detect = NULL, |
| .enable = enable_rgb, |
| .mode = { |
| .name = "svga", |
| .refresh = 60, |
| .xres = 800, |
| .yres = 600, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = 0, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 2, |
| .addr = 0x41, |
| .pixfmt = IPU_PIX_FMT_LVDS666, |
| .detect = detect_i2c, |
| .enable = enable_lvds, |
| .mode = { |
| .name = "amp1024x600", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 600, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 0, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_LVDS666, |
| .detect = 0, |
| .enable = enable_lvds, |
| .mode = { |
| .name = "wvga-lvds", |
| .refresh = 57, |
| .xres = 800, |
| .yres = 480, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 2, |
| .addr = 0x48, |
| .pixfmt = IPU_PIX_FMT_RGB666, |
| .detect = detect_i2c, |
| .enable = enable_rgb, |
| .mode = { |
| .name = "wvga-rgb", |
| .refresh = 57, |
| .xres = 800, |
| .yres = 480, |
| .pixclock = 37037, |
| .left_margin = 40, |
| .right_margin = 60, |
| .upper_margin = 10, |
| .lower_margin = 10, |
| .hsync_len = 20, |
| .vsync_len = 10, |
| .sync = 0, |
| .vmode = FB_VMODE_NONINTERLACED |
| } }, { |
| .bus = 0, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .detect = NULL, |
| .enable = enable_rgb, |
| .mode = { |
| .name = "qvga", |
| .refresh = 60, |
| .xres = 320, |
| .yres = 240, |
| .pixclock = 37037, |
| .left_margin = 38, |
| .right_margin = 37, |
| .upper_margin = 16, |
| .lower_margin = 15, |
| .hsync_len = 30, |
| .vsync_len = 3, |
| .sync = 0, |
| .vmode = FB_VMODE_NONINTERLACED |
| } } }; |
| size_t display_count = ARRAY_SIZE(displays); |
| |
| int board_cfb_skip(void) |
| { |
| return NULL != getenv("novideo"); |
| } |
| |
| static void setup_display(void) |
| { |
| struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; |
| int reg; |
| |
| enable_ipu_clock(); |
| imx_setup_hdmi(); |
| /* Turn on LDB0,IPU,IPU DI0 clocks */ |
| reg = __raw_readl(&mxc_ccm->CCGR3); |
| reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; |
| writel(reg, &mxc_ccm->CCGR3); |
| |
| /* set LDB0, LDB1 clk select to 011/011 */ |
| reg = readl(&mxc_ccm->cs2cdr); |
| reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
| |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); |
| reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
| |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); |
| writel(reg, &mxc_ccm->cs2cdr); |
| |
| reg = readl(&mxc_ccm->cscmr2); |
| reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; |
| writel(reg, &mxc_ccm->cscmr2); |
| |
| reg = readl(&mxc_ccm->chsccdr); |
| reg |= (CHSCCDR_CLK_SEL_LDB_DI0 |
| <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); |
| writel(reg, &mxc_ccm->chsccdr); |
| |
| reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
| |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH |
| |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
| |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
| |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT |
| |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
| |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT |
| |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED |
| |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; |
| writel(reg, &iomux->gpr[2]); |
| |
| reg = readl(&iomux->gpr[3]); |
| reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
| |IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) |
| | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 |
| <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); |
| writel(reg, &iomux->gpr[3]); |
| |
| /* backlights off until needed */ |
| imx_iomux_v3_setup_multiple_pads(backlight_pads, |
| ARRAY_SIZE(backlight_pads)); |
| gpio_direction_input(LVDS_BACKLIGHT_GP); |
| gpio_direction_input(RGB_BACKLIGHT_GP); |
| } |
| #endif |
| |
| static iomux_v3_cfg_t const init_pads[] = { |
| /* SGTL5000 sys_mclk */ |
| NEW_PAD_CTRL(MX6_PAD_GPIO_0__CCM_CLKO1, OUTPUT_40OHM), |
| |
| /* J5 - Camera MCLK */ |
| NEW_PAD_CTRL(MX6_PAD_GPIO_3__CCM_CLKO2, OUTPUT_40OHM), |
| |
| /* wl1271 pads on nitrogen6x */ |
| /* WL12XX_WL_IRQ_GP */ |
| NEW_PAD_CTRL(MX6_PAD_NANDF_CS1__GPIO6_IO14, WEAK_PULLDOWN), |
| /* WL12XX_WL_ENABLE_GP */ |
| NEW_PAD_CTRL(MX6_PAD_NANDF_CS2__GPIO6_IO15, OUTPUT_40OHM), |
| /* WL12XX_BT_ENABLE_GP */ |
| NEW_PAD_CTRL(MX6_PAD_NANDF_CS3__GPIO6_IO16, OUTPUT_40OHM), |
| /* USB otg power */ |
| NEW_PAD_CTRL(MX6_PAD_EIM_D22__GPIO3_IO22, OUTPUT_40OHM), |
| NEW_PAD_CTRL(MX6_PAD_NANDF_D5__GPIO2_IO05, OUTPUT_40OHM), |
| NEW_PAD_CTRL(MX6_PAD_NANDF_WP_B__GPIO6_IO09, OUTPUT_40OHM), |
| NEW_PAD_CTRL(MX6_PAD_GPIO_8__GPIO1_IO08, OUTPUT_40OHM), |
| NEW_PAD_CTRL(MX6_PAD_GPIO_6__GPIO1_IO06, OUTPUT_40OHM), |
| }; |
| |
| #define WL12XX_WL_IRQ_GP IMX_GPIO_NR(6, 14) |
| |
| static unsigned gpios_out_low[] = { |
| /* Disable wl1271 */ |
| IMX_GPIO_NR(6, 15), /* disable wireless */ |
| IMX_GPIO_NR(6, 16), /* disable bluetooth */ |
| IMX_GPIO_NR(3, 22), /* disable USB otg power */ |
| IMX_GPIO_NR(2, 5), /* ov5640 mipi camera reset */ |
| IMX_GPIO_NR(1, 8), /* ov5642 reset */ |
| }; |
| |
| static unsigned gpios_out_high[] = { |
| IMX_GPIO_NR(1, 6), /* ov5642 powerdown */ |
| IMX_GPIO_NR(6, 9), /* ov5640 mipi camera power down */ |
| }; |
| |
| static void set_gpios(unsigned *p, int cnt, int val) |
| { |
| int i; |
| |
| for (i = 0; i < cnt; i++) |
| gpio_direction_output(*p++, val); |
| } |
| |
| int board_early_init_f(void) |
| { |
| setup_iomux_uart(); |
| |
| set_gpios(gpios_out_high, ARRAY_SIZE(gpios_out_high), 1); |
| set_gpios(gpios_out_low, ARRAY_SIZE(gpios_out_low), 0); |
| gpio_direction_input(WL12XX_WL_IRQ_GP); |
| |
| imx_iomux_v3_setup_multiple_pads(wl12xx_pads, ARRAY_SIZE(wl12xx_pads)); |
| imx_iomux_v3_setup_multiple_pads(init_pads, ARRAY_SIZE(init_pads)); |
| setup_buttons(); |
| |
| #if defined(CONFIG_VIDEO_IPUV3) |
| setup_display(); |
| #endif |
| return 0; |
| } |
| |
| /* |
| * Do not overwrite the console |
| * Use always serial for U-Boot console |
| */ |
| int overwrite_console(void) |
| { |
| return 1; |
| } |
| |
| int board_init(void) |
| { |
| struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; |
| |
| clrsetbits_le32(&iomuxc_regs->gpr[1], |
| IOMUXC_GPR1_OTG_ID_MASK, |
| IOMUXC_GPR1_OTG_ID_GPIO1); |
| |
| imx_iomux_v3_setup_multiple_pads(misc_pads, ARRAY_SIZE(misc_pads)); |
| |
| /* address of boot parameters */ |
| gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; |
| |
| #ifdef CONFIG_MXC_SPI |
| setup_spi(); |
| #endif |
| imx_iomux_v3_setup_multiple_pads( |
| usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); |
| setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0); |
| setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); |
| setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); |
| |
| #ifdef CONFIG_CMD_SATA |
| setup_sata(); |
| #endif |
| |
| return 0; |
| } |
| |
| int checkboard(void) |
| { |
| if (gpio_get_value(WL12XX_WL_IRQ_GP)) |
| puts("Board: Nitrogen6X\n"); |
| else |
| puts("Board: SABRE Lite\n"); |
| |
| return 0; |
| } |
| |
| struct button_key { |
| char const *name; |
| unsigned gpnum; |
| char ident; |
| }; |
| |
| static struct button_key const buttons[] = { |
| {"back", IMX_GPIO_NR(2, 2), 'B'}, |
| {"home", IMX_GPIO_NR(2, 4), 'H'}, |
| {"menu", IMX_GPIO_NR(2, 1), 'M'}, |
| {"search", IMX_GPIO_NR(2, 3), 'S'}, |
| {"volup", IMX_GPIO_NR(7, 13), 'V'}, |
| {"voldown", IMX_GPIO_NR(4, 5), 'v'}, |
| }; |
| |
| /* |
| * generate a null-terminated string containing the buttons pressed |
| * returns number of keys pressed |
| */ |
| static int read_keys(char *buf) |
| { |
| int i, numpressed = 0; |
| for (i = 0; i < ARRAY_SIZE(buttons); i++) { |
| if (!gpio_get_value(buttons[i].gpnum)) |
| buf[numpressed++] = buttons[i].ident; |
| } |
| buf[numpressed] = '\0'; |
| return numpressed; |
| } |
| |
| static int do_kbd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
| { |
| char envvalue[ARRAY_SIZE(buttons)+1]; |
| int numpressed = read_keys(envvalue); |
| setenv("keybd", envvalue); |
| return numpressed == 0; |
| } |
| |
| U_BOOT_CMD( |
| kbd, 1, 1, do_kbd, |
| "Tests for keypresses, sets 'keybd' environment variable", |
| "Returns 0 (true) to shell if key is pressed." |
| ); |
| |
| #ifdef CONFIG_PREBOOT |
| static char const kbd_magic_prefix[] = "key_magic"; |
| static char const kbd_command_prefix[] = "key_cmd"; |
| |
| static void preboot_keys(void) |
| { |
| int numpressed; |
| char keypress[ARRAY_SIZE(buttons)+1]; |
| numpressed = read_keys(keypress); |
| if (numpressed) { |
| char *kbd_magic_keys = getenv("magic_keys"); |
| char *suffix; |
| /* |
| * loop over all magic keys |
| */ |
| for (suffix = kbd_magic_keys; *suffix; ++suffix) { |
| char *keys; |
| char magic[sizeof(kbd_magic_prefix) + 1]; |
| sprintf(magic, "%s%c", kbd_magic_prefix, *suffix); |
| keys = getenv(magic); |
| if (keys) { |
| if (!strcmp(keys, keypress)) |
| break; |
| } |
| } |
| if (*suffix) { |
| char cmd_name[sizeof(kbd_command_prefix) + 1]; |
| char *cmd; |
| sprintf(cmd_name, "%s%c", kbd_command_prefix, *suffix); |
| cmd = getenv(cmd_name); |
| if (cmd) { |
| setenv("preboot", cmd); |
| return; |
| } |
| } |
| } |
| } |
| #endif |
| |
| #ifdef CONFIG_CMD_BMODE |
| static const struct boot_mode board_boot_modes[] = { |
| /* 4 bit bus width */ |
| {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, |
| {"mmc1", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, |
| {NULL, 0}, |
| }; |
| #endif |
| |
| int misc_init_r(void) |
| { |
| #ifdef CONFIG_PREBOOT |
| preboot_keys(); |
| #endif |
| |
| #ifdef CONFIG_CMD_BMODE |
| add_board_boot_modes(board_boot_modes); |
| #endif |
| return 0; |
| } |