| CONFIG_ARM=y |
| CONFIG_SKIP_LOWLEVEL_INIT=y |
| CONFIG_SYS_DCACHE_OFF=y |
| CONFIG_ARCH_CPU_INIT=y |
| CONFIG_SYS_THUMB_BUILD=y |
| CONFIG_ARCH_KIRKWOOD=y |
| CONFIG_SYS_KWD_CONFIG="board/Marvell/openrd/kwbimage.cfg" |
| CONFIG_SYS_TEXT_BASE=0x600000 |
| CONFIG_NR_DRAM_BANKS=2 |
| CONFIG_TARGET_OPENRD=y |
| CONFIG_BOARD_IS_OPENRD_CLIENT=y |
| CONFIG_ENV_SIZE=0x20000 |
| CONFIG_ENV_OFFSET=0x80000 |
| CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-client" |
| CONFIG_IDENT_STRING="\nOpenRD-Client" |
| # CONFIG_SYS_MALLOC_F is not set |
| CONFIG_HAS_BOARD_SIZE_LIMIT=y |
| CONFIG_BOARD_SIZE_LIMIT=524288 |
| CONFIG_SYS_LOAD_ADDR=0x800000 |
| CONFIG_BOOTDELAY=3 |
| CONFIG_USE_BOOTCOMMAND=y |
| CONFIG_BOOTCOMMAND="${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; ${x_bootcmd_usb}; bootm 0x6400000;" |
| CONFIG_USE_PREBOOT=y |
| CONFIG_LOGLEVEL=2 |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_RESET_PHY_R=y |
| # CONFIG_CMD_FLASH is not set |
| CONFIG_CMD_IDE=y |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_NAND=y |
| CONFIG_CMD_USB=y |
| # CONFIG_CMD_SETEXPR is not set |
| CONFIG_CMD_DHCP=y |
| CONFIG_CMD_MII=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_EXT2=y |
| CONFIG_CMD_FAT=y |
| CONFIG_CMD_JFFS2=y |
| CONFIG_CMD_MTDPARTS=y |
| CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd" |
| CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000@0x000000(uboot),0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)" |
| CONFIG_CMD_UBI=y |
| CONFIG_ISO_PARTITION=y |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_OVERWRITE=y |
| CONFIG_ENV_IS_IN_NAND=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_NETCONSOLE=y |
| CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y |
| CONFIG_DM=y |
| CONFIG_SYS_ATA_STRIDE=4 |
| CONFIG_SYS_ATA_DATA_OFFSET=0x100 |
| CONFIG_SYS_ATA_REG_OFFSET=0x100 |
| CONFIG_SYS_ATA_ALT_OFFSET=0x100 |
| CONFIG_SYS_ATA_IDE0_OFFSET=0x2000 |
| CONFIG_SYS_ATA_IDE1_OFFSET=0x4000 |
| # CONFIG_MMC_HW_PARTITIONING is not set |
| CONFIG_MTD=y |
| CONFIG_MTD_RAW_NAND=y |
| CONFIG_MVGBE=y |
| CONFIG_MII=y |
| CONFIG_SYS_NS16550=y |
| CONFIG_USB=y |
| CONFIG_USB_EHCI_HCD=y |