include/configs/delta.h - github/trini/u-boot - Gitiles

 /*
  * Configuation settings for the Delta board.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */
 #define CONFIG_CPU_MONAHANS	1	/* Intel Monahan CPU    */
 #define CONFIG_DELTA		1	/* Delta board       */

 /* #define CONFIG_LCD		1 */
 #ifdef CONFIG_LCD
 #define CONFIG_SHARP_LM8V31
 #endif
 #define BOARD_LATE_INIT		1

 #undef CONFIG_SKIP_RELOCATE_UBOOT
 #undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */

 /* we will never enable dcache, because we have to setup MMU first */
 #define CONFIG_SYS_NO_DCACHE

 /*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN	    (CONFIG_ENV_SIZE + 256*1024)
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */

 /*
  * Hardware drivers
  */
 #undef TURN_ON_ETHERNET
 #ifdef TURN_ON_ETHERNET
 # define CONFIG_DRIVER_SMC91111 1
 # define CONFIG_SMC91111_BASE   0x14000300
 # define CONFIG_SMC91111_EXT_PHY
 # define CONFIG_SMC_USE_32_BIT
 # undef CONFIG_SMC_USE_IOFUNCS          /* just for use with the kernel */
 #endif

 #define CONFIG_HARD_I2C		1	/* required for DA9030 access */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed */
 #define CONFIG_SYS_I2C_SLAVE		1	/* I2C controllers address */
 #define DA9030_I2C_ADDR		0x49	/* I2C address of DA9030 */
 #define CONFIG_SYS_DA9030_EXTON_DELAY	100000	/* wait x us after DA9030 reset via EXTON */
 #define CONFIG_SYS_I2C_INIT_BOARD	1
 /* #define CONFIG_HW_WATCHDOG	1	/\* Required for hitting the DA9030 WD *\/ */

 #define DELTA_CHECK_KEYBD	1	/* check for keys pressed during boot */
 #define CONFIG_PREBOOT		"\0"

 #ifdef DELTA_CHECK_KEYBD
 # define KEYBD_DATALEN		4	/* we have four keys */
 # define KEYBD_KP_DKIN0		0x1	/* vol+ */
 # define KEYBD_KP_DKIN1		0x2	/* vol- */
 # define KEYBD_KP_DKIN2		0x3	/* multi */
 # define KEYBD_KP_DKIN5		0x4	/* SWKEY_GN */
 #endif /* DELTA_CHECK_KEYBD */

 /*
  * select serial console configuration
  */
 #define CONFIG_PXA_SERIAL
 #define CONFIG_FFUART		1

 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE

 #define CONFIG_BAUDRATE		115200


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #ifdef TURN_ON_ETHERNET

 #define CONFIG_CMD_PING

 #else

 #define CONFIG_CMD_SAVEENV
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_I2C

 #undef CONFIG_CMD_NET
 #undef CONFIG_CMD_FLASH
 #undef CONFIG_CMD_IMLS

 #endif

 /* USB */
 #define CONFIG_USB_OHCI_NEW	1
 #define CONFIG_USB_STORAGE      1
 #define CONFIG_DOS_PARTITION    1

 #include <asm/arch/pxa-regs.h> /* for OHCI_REGS_BASE */

 #undef CONFIG_SYS_USB_OHCI_BOARD_INIT
 #define CONFIG_SYS_USB_OHCI_CPU_INIT	1
 #define CONFIG_SYS_USB_OHCI_REGS_BASE	OHCI_REGS_BASE
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME	"delta"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	3

 #define CONFIG_BOOTDELAY	-1
 #define CONFIG_ETHADDR		08:00:3e:26:0a:5b
 #define CONFIG_NETMASK		255.255.0.0
 #define CONFIG_IPADDR		192.168.0.21
 #define CONFIG_SERVERIP		192.168.0.250
 #define CONFIG_BOOTCOMMAND	"bootm 80000"
 #define CONFIG_BOOTARGS		"root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_TIMESTAMP

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
 #endif

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_HUSH_PARSER		1
 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "

 #define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
 #ifdef CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_PROMPT		"$ "		/* Monitor Command Prompt */
 #else
 #define CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt */
 #endif
 #define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 #define CONFIG_SYS_DEVICE_NULLDEV	1

 #define CONFIG_SYS_MEMTEST_START	0x80400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x80800000	/* 4 ... 8 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */

 #define CONFIG_SYS_HZ			1000

 /* Monahans Core Frequency */
 #define CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO		16 /* valid values: 8, 16, 24, 31 */
 #define CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO	1  /* valid values: 1, 2 */


 						/* valid baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 #ifdef CONFIG_MMC
 #define CONFIG_PXA_MMC
 #define CONFIG_CMD_MMC
 #define CONFIG_SYS_MMC_BASE		0xF0000000
 #endif

 /*
  * Stack sizes
  *
  * The stack sizes are set up in start.S using the settings below
  */
 #define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
 #ifdef CONFIG_USE_IRQ
 #define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
 #define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
 #endif

 /*
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	4	   /* we have 2 banks of DRAM */
 #define PHYS_SDRAM_1		0x80000000 /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE	0x1000000  /* 64 MB */
 #define PHYS_SDRAM_2		0x81000000 /* SDRAM Bank #2 */
 #define PHYS_SDRAM_2_SIZE	0x1000000  /* 64 MB */
 #define PHYS_SDRAM_3		0x82000000 /* SDRAM Bank #3 */
 #define PHYS_SDRAM_3_SIZE	0x1000000  /* 64 MB */
 #define PHYS_SDRAM_4		0x83000000 /* SDRAM Bank #4 */
 #define PHYS_SDRAM_4_SIZE	0x1000000  /* 64 MB */

 #define CONFIG_SYS_DRAM_BASE		0x80000000 /* at CS0 */
 #define CONFIG_SYS_DRAM_SIZE		0x04000000 /* 64 MB Ram */

 #undef CONFIG_SYS_SKIP_DRAM_SCRUB

 /*
  * NAND Flash
  */
 #undef CONFIG_NAND_LEGACY

 #define CONFIG_SYS_NAND0_BASE		0x0 /* 0x43100040 */ /* 0x10000000 */
 #undef CONFIG_SYS_NAND1_BASE

 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND0_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND devices */

 #define CONFIG_SYS_64BIT_VSPRINTF		/* needed for nand_util.c */

 /* nand timeout values */
 #define CONFIG_SYS_NAND_PROG_ERASE_TO	3000
 #define CONFIG_SYS_NAND_OTHER_TO	100
 #define CONFIG_SYS_NAND_SENDCMD_RETRY	3
 #undef NAND_ALLOW_ERASE_ALL	/* Allow erasing bad blocks - don't use */

 /* NAND Timing Parameters (in ns) */
 #define NAND_TIMING_tCH		10
 #define NAND_TIMING_tCS		0
 #define NAND_TIMING_tWH		20
 #define NAND_TIMING_tWP		40

 #define NAND_TIMING_tRH		20
 #define NAND_TIMING_tRP		40

 #define NAND_TIMING_tR		11123
 #define NAND_TIMING_tWHR	100
 #define NAND_TIMING_tAR		10

 /* NAND debugging */
 #define CONFIG_SYS_DFC_DEBUG1 /* usefull */
 #undef CONFIG_SYS_DFC_DEBUG2  /* noisy */
 #undef CONFIG_SYS_DFC_DEBUG3  /* extremly noisy  */

 #define CONFIG_MTD_DEBUG
 #define CONFIG_MTD_DEBUG_VERBOSE 1

 #define ADDR_COLUMN		1
 #define ADDR_PAGE		2
 #define ADDR_COLUMN_PAGE	3

 #define NAND_ChipID_UNKNOWN	0x00
 #define NAND_MAX_FLOORS		1

 #define CONFIG_SYS_NO_FLASH		1

 #define CONFIG_ENV_IS_IN_NAND	1
 #define CONFIG_ENV_OFFSET		0x40000
 #define CONFIG_ENV_OFFSET_REDUND	0x44000
 #define CONFIG_ENV_SIZE		0x4000

 #endif	/* __CONFIG_H */
	/*
	* Configuation settings for the Delta board.
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/
	#define CONFIG_CPU_MONAHANS 1 /* Intel Monahan CPU */
	#define CONFIG_DELTA 1 /* Delta board */

	/* #define CONFIG_LCD 1 */
	#ifdef CONFIG_LCD
	#define CONFIG_SHARP_LM8V31
	#endif
	#define BOARD_LATE_INIT 1

	#undef CONFIG_SKIP_RELOCATE_UBOOT
	#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */

	/* we will never enable dcache, because we have to setup MMU first */
	#define CONFIG_SYS_NO_DCACHE

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024)
	#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */

	/*
	* Hardware drivers
	*/
	#undef TURN_ON_ETHERNET
	#ifdef TURN_ON_ETHERNET
	# define CONFIG_DRIVER_SMC91111 1
	# define CONFIG_SMC91111_BASE 0x14000300
	# define CONFIG_SMC91111_EXT_PHY
	# define CONFIG_SMC_USE_32_BIT
	# undef CONFIG_SMC_USE_IOFUNCS /* just for use with the kernel */
	#endif

	#define CONFIG_HARD_I2C 1 /* required for DA9030 access */
	#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
	#define CONFIG_SYS_I2C_SLAVE 1 /* I2C controllers address */
	#define DA9030_I2C_ADDR 0x49 /* I2C address of DA9030 */
	#define CONFIG_SYS_DA9030_EXTON_DELAY 100000 /* wait x us after DA9030 reset via EXTON */
	#define CONFIG_SYS_I2C_INIT_BOARD 1
	/* #define CONFIG_HW_WATCHDOG 1 /\* Required for hitting the DA9030 WD \/ /

	#define DELTA_CHECK_KEYBD 1 /* check for keys pressed during boot */
	#define CONFIG_PREBOOT "\0"

	#ifdef DELTA_CHECK_KEYBD
	# define KEYBD_DATALEN 4 /* we have four keys */
	# define KEYBD_KP_DKIN0 0x1 /* vol+ */
	# define KEYBD_KP_DKIN1 0x2 /* vol- */
	# define KEYBD_KP_DKIN2 0x3 /* multi */
	# define KEYBD_KP_DKIN5 0x4 /* SWKEY_GN */
	#endif /* DELTA_CHECK_KEYBD */

	/*
	* select serial console configuration
	*/
	#define CONFIG_PXA_SERIAL
	#define CONFIG_FFUART 1

	/* allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE

	#define CONFIG_BAUDRATE 115200


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#ifdef TURN_ON_ETHERNET

	#define CONFIG_CMD_PING

	#else

	#define CONFIG_CMD_SAVEENV
	#define CONFIG_CMD_NAND
	#define CONFIG_CMD_I2C

	#undef CONFIG_CMD_NET
	#undef CONFIG_CMD_FLASH
	#undef CONFIG_CMD_IMLS

	#endif

	/* USB */
	#define CONFIG_USB_OHCI_NEW 1
	#define CONFIG_USB_STORAGE 1
	#define CONFIG_DOS_PARTITION 1

	#include <asm/arch/pxa-regs.h> /* for OHCI_REGS_BASE */

	#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
	#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
	#define CONFIG_SYS_USB_OHCI_REGS_BASE OHCI_REGS_BASE
	#define CONFIG_SYS_USB_OHCI_SLOT_NAME "delta"
	#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3

	#define CONFIG_BOOTDELAY -1
	#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
	#define CONFIG_NETMASK 255.255.0.0
	#define CONFIG_IPADDR 192.168.0.21
	#define CONFIG_SERVERIP 192.168.0.250
	#define CONFIG_BOOTCOMMAND "bootm 80000"
	#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
	#define CONFIG_CMDLINE_TAG
	#define CONFIG_TIMESTAMP

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_HUSH_PARSER 1
	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "

	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#ifdef CONFIG_SYS_HUSH_PARSER
	#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
	#else
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#endif
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
	#define CONFIG_SYS_DEVICE_NULLDEV 1

	#define CONFIG_SYS_MEMTEST_START 0x80400000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x80800000 /* 4 ... 8 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */

	#define CONFIG_SYS_HZ 1000

	/* Monahans Core Frequency */
	#define CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO 16 /* valid values: 8, 16, 24, 31 */
	#define CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO 1 /* valid values: 1, 2 */


	/* valid baudrates */
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	#ifdef CONFIG_MMC
	#define CONFIG_PXA_MMC
	#define CONFIG_CMD_MMC
	#define CONFIG_SYS_MMC_BASE 0xF0000000
	#endif

	/*
	* Stack sizes
	*
	* The stack sizes are set up in start.S using the settings below
	*/
	#define CONFIG_STACKSIZE (1281024) / regular stack */
	#ifdef CONFIG_USE_IRQ
	#define CONFIG_STACKSIZE_IRQ (41024) / IRQ stack */
	#define CONFIG_STACKSIZE_FIQ (41024) / FIQ stack */
	#endif

	/*
	* Physical Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */
	#define PHYS_SDRAM_1 0x80000000 /* SDRAM Bank #1 */
	#define PHYS_SDRAM_1_SIZE 0x1000000 /* 64 MB */
	#define PHYS_SDRAM_2 0x81000000 /* SDRAM Bank #2 */
	#define PHYS_SDRAM_2_SIZE 0x1000000 /* 64 MB */
	#define PHYS_SDRAM_3 0x82000000 /* SDRAM Bank #3 */
	#define PHYS_SDRAM_3_SIZE 0x1000000 /* 64 MB */
	#define PHYS_SDRAM_4 0x83000000 /* SDRAM Bank #4 */
	#define PHYS_SDRAM_4_SIZE 0x1000000 /* 64 MB */

	#define CONFIG_SYS_DRAM_BASE 0x80000000 /* at CS0 */
	#define CONFIG_SYS_DRAM_SIZE 0x04000000 /* 64 MB Ram */

	#undef CONFIG_SYS_SKIP_DRAM_SCRUB

	/*
	* NAND Flash
	*/
	#undef CONFIG_NAND_LEGACY

	#define CONFIG_SYS_NAND0_BASE 0x0 /* 0x43100040 / / 0x10000000 */
	#undef CONFIG_SYS_NAND1_BASE

	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE }
	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */

	#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */

	/* nand timeout values */
	#define CONFIG_SYS_NAND_PROG_ERASE_TO 3000
	#define CONFIG_SYS_NAND_OTHER_TO 100
	#define CONFIG_SYS_NAND_SENDCMD_RETRY 3
	#undef NAND_ALLOW_ERASE_ALL /* Allow erasing bad blocks - don't use */

	/* NAND Timing Parameters (in ns) */
	#define NAND_TIMING_tCH 10
	#define NAND_TIMING_tCS 0
	#define NAND_TIMING_tWH 20
	#define NAND_TIMING_tWP 40

	#define NAND_TIMING_tRH 20
	#define NAND_TIMING_tRP 40

	#define NAND_TIMING_tR 11123
	#define NAND_TIMING_tWHR 100
	#define NAND_TIMING_tAR 10

	/* NAND debugging */
	#define CONFIG_SYS_DFC_DEBUG1 /* usefull */
	#undef CONFIG_SYS_DFC_DEBUG2 /* noisy */
	#undef CONFIG_SYS_DFC_DEBUG3 /* extremly noisy */

	#define CONFIG_MTD_DEBUG
	#define CONFIG_MTD_DEBUG_VERBOSE 1

	#define ADDR_COLUMN 1
	#define ADDR_PAGE 2
	#define ADDR_COLUMN_PAGE 3

	#define NAND_ChipID_UNKNOWN 0x00
	#define NAND_MAX_FLOORS 1

	#define CONFIG_SYS_NO_FLASH 1

	#define CONFIG_ENV_IS_IN_NAND 1
	#define CONFIG_ENV_OFFSET 0x40000
	#define CONFIG_ENV_OFFSET_REDUND 0x44000
	#define CONFIG_ENV_SIZE 0x4000

	#endif /* __CONFIG_H */