blob: 2dd9d3129502c198eee274457471ca6f84edb1ed [file] [log] [blame]
/*
* Copyright (C) 2013-2016 Synopsys, Inc. All rights reserved.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_AXS10X_H_
#define _CONFIG_AXS10X_H_
#include <linux/sizes.h>
/*
* CPU configuration
*/
#define CONFIG_SYS_TIMER_RATE CONFIG_SYS_CLK_FREQ
#define ARC_FPGA_PERIPHERAL_BASE 0xE0000000
#define ARC_APB_PERIPHERAL_BASE 0xF0000000
#define ARC_DWMMC_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x15000)
#define ARC_DWGMAC_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x18000)
/*
* Memory configuration
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_SDRAM_SIZE SZ_512M
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_MALLOC_LEN SZ_2M
#define CONFIG_SYS_BOOTM_LEN SZ_32M
#define CONFIG_SYS_LOAD_ADDR 0x82000000
/*
* This board might be of different versions so handle it
*/
#define CONFIG_BOARD_TYPES
#define CONFIG_BOARD_EARLY_INIT_F
/*
* NAND Flash configuration
*/
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_NAND_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x16000)
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/*
* UART configuration
*/
#define CONFIG_DW_SERIAL
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_CLK 33333333
#define CONFIG_SYS_NS16550_MEM32
#define CONFIG_BAUDRATE 115200
/*
* I2C configuration
*/
#define CONFIG_SYS_I2C
#define CONFIG_I2C_ENV_EEPROM_BUS 2
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SPEED1 100000
#define CONFIG_SYS_I2C_SPEED2 100000
#define CONFIG_SYS_I2C_SLAVE 0
#define CONFIG_SYS_I2C_SLAVE1 0
#define CONFIG_SYS_I2C_SLAVE2 0
#define CONFIG_SYS_I2C_BASE 0xE001D000
#define CONFIG_SYS_I2C_BASE1 0xE001E000
#define CONFIG_SYS_I2C_BASE2 0xE001F000
#define CONFIG_SYS_I2C_BUS_MAX 3
#define IC_CLK 50
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR (0xA8 >> 1)
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 64
/*
* SD/MMC configuration
*/
#define CONFIG_GENERIC_MMC
#define CONFIG_DOS_PARTITION
/*
* Ethernet PHY configuration
*/
#define CONFIG_MII
#define CONFIG_PHY_GIGE
/*
* USB 1.1 configuration
*/
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
/*
* Commands still not supported in Kconfig
*/
#define CONFIG_CMD_NAND
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 16
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_SIZE SZ_512
#define CONFIG_ENV_OFFSET 0
/*
* Environment configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_BOOTARGS "console=ttyS3,115200n8"
#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
/*
* Console configuration
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_CBSIZE SZ_256
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
/*
* Misc utility configuration
*/
#define CONFIG_BOUNCE_BUFFER
#endif /* _CONFIG_AXS10X_H_ */