| U-Boot for UniPhier SoC family |
| ============================== |
| |
| |
| Recommended toolchains |
| ---------------------- |
| |
| The UniPhir platform is well tested with Linaro toolchanis. |
| You can download pre-built toolchains from: |
| |
| http://www.linaro.org/downloads/ |
| |
| |
| Compile the source |
| ------------------ |
| |
| sLD3 reference board: |
| $ make uniphier_sld3_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- |
| |
| LD4 reference board: |
| $ make uniphier_ld4_sld8_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- |
| |
| sLD8 reference board: |
| $ make uniphier_ld4_sld8_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-sld8-ref |
| |
| Pro4 reference board: |
| $ make uniphier_pro4_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- |
| |
| Pro4 Ace board: |
| $ make uniphier_pro4_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro4-ace |
| |
| Pro4 Sanji board: |
| $ make uniphier_pro4_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro4-sanji |
| |
| Pro5 4KBOX Board: |
| $ make uniphier_pxs2_ld6b_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pro5-4kbox |
| |
| PXs2 Gentil board: |
| $ make uniphier_pxs2_ld6b_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pxs2-gentil |
| |
| PXs2 Vodka board: |
| $ make uniphier_pxs2_ld6b_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- |
| |
| LD6b reference board: |
| $ make uniphier_pxs2_ld6b_defconfig |
| $ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-ld6b-ref |
| |
| LD11 reference board: |
| $ make uniphier_ld11_defconfig |
| $ make CROSS_COMPILE=aarch64-linux-gnu- |
| |
| LD20 reference board: |
| $ make uniphier_ld20_defconfig |
| $ make CROSS_COMPILE=aarch64-linux-gnu- |
| |
| PXs3 reference board: |
| $ make uniphier_v8_defconfig |
| $ make CROSS_COMPILE=aarch64-linux-gnu- DEVICE_TREE=uniphier-pxs3-ref |
| |
| You may wish to change the "CROSS_COMPILE=..." to use your favorite compiler. |
| |
| |
| Burn U-Boot images to NAND |
| -------------------------- |
| |
| Write the following to the NAND device: |
| |
| - spl/u-boot-spl.bin at the offset address 0x00000000 |
| - u-boot.bin at the offset address 0x00020000 |
| |
| or |
| |
| - u-boot-with-spl.bin at the offset address 0x00000000 |
| |
| If a TFTP server is available, the images can be easily updated. |
| Just copy the u-boot-spl.bin and u-boot.bin to the TFTP public directory, |
| and then run the following command at the U-Boot command line: |
| |
| => run nandupdate |
| |
| |
| Burn U-Boot images to eMMC |
| -------------------------- |
| |
| Write the following to the Boot partition 1 of the eMMC device: |
| |
| - spl/u-boot-spl.bin at the offset address 0x00000000 |
| - u-boot.bin at the offset address 0x00020000 |
| |
| or |
| |
| - u-boot-with-spl.bin at the offset address 0x00000000 |
| |
| If a TFTP server is available, the images can be easily updated. |
| Just copy the u-boot-spl.bin and u-boot.bin to the TFTP public directory, |
| and then run the following command at the U-Boot command line: |
| |
| => run emmcupdate |
| |
| |
| UniPhier specific commands |
| -------------------------- |
| |
| - pinmon (enabled by CONFIG_CMD_PINMON) |
| shows the boot mode pins that has been latched at the power-on reset |
| |
| - ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP) |
| shows the DDR PHY parameters set by the PHY training |
| |
| - ddrmphy (enabled by CONFIG_CMD_DDRMPHY_DUMP) |
| shows the DDR Multi PHY parameters set by the PHY training |
| |
| |
| Supported devices |
| ----------------- |
| |
| - UART (on-chip) |
| - NAND |
| - SD/eMMC |
| - USB 2.0 (EHCI) |
| - USB 3.0 (xHCI) |
| - GPIO |
| - LAN (on-board SMSC9118) |
| - I2C |
| - EEPROM (connected to the on-board I2C bus) |
| - Support card (SRAM, NOR flash, some peripherals) |
| |
| |
| Micro Support Card |
| ------------------ |
| |
| The recommended bit switch settings are as follows: |
| |
| SW2 OFF(1)/ON(0) Description |
| ------------------------------------------ |
| bit 1 <---- BKSZ[0] |
| bit 2 ----> BKSZ[1] |
| bit 3 <---- SoC Bus Width 16/32 |
| bit 4 <---- SERIAL_SEL[0] |
| bit 5 ----> SERIAL_SEL[1] |
| bit 6 ----> BOOTSWAP_EN |
| bit 7 <---- CS1/CS5 |
| bit 8 <---- SOC_SERIAL_DISABLE |
| |
| SW8 OFF(1)/ON(0) Description |
| ------------------------------------------ |
| bit 1 <---- CS1_SPLIT |
| bit 2 <---- CASE9_ON |
| bit 3 <---- CASE10_ON |
| bit 4 Don't Care Reserve |
| bit 5 Don't Care Reserve |
| bit 6 Don't Care Reserve |
| bit 7 ----> BURST_EN |
| bit 8 ----> FLASHBUS32_16 |
| |
| The BKSZ[1:0] specifies the address range of memory slot and peripherals |
| as follows: |
| |
| BKSZ Description RAM slot Peripherals |
| -------------------------------------------------------------------- |
| 0b00 15MB RAM / 1MB Peri 00000000-00efffff 00f00000-00ffffff |
| 0b01 31MB RAM / 1MB Peri 00000000-01efffff 01f00000-01ffffff |
| 0b10 64MB RAM / 1MB Peri 00000000-03efffff 03f00000-03ffffff |
| 0b11 127MB RAM / 1MB Peri 00000000-07efffff 07f00000-07ffffff |
| |
| Set BSKZ[1:0] to 0b01 for U-Boot. |
| This mode is the most handy because EA[24] is always supported by the save pin |
| mode of the system bus. On the other hand, EA[25] is not supported for some |
| newer SoCs. Even if it is, EA[25] is not connected on most of the boards. |
| |
| -- |
| Masahiro Yamada <yamada.masahiro@socionext.com> |
| Jan. 2017 |