drivers/ddr/altera/sequencer.h - github/trini/u-boot - Gitiles

 /*
  * Copyright Altera Corporation (C) 2012-2015
  *
  * SPDX-License-Identifier:    BSD-3-Clause
  */

 #ifndef _SEQUENCER_H_
 #define _SEQUENCER_H_

 #define RW_MGR_NUM_DM_PER_WRITE_GROUP (RW_MGR_MEM_DATA_MASK_WIDTH \
 	/ RW_MGR_MEM_IF_WRITE_DQS_WIDTH)
 #define RW_MGR_NUM_TRUE_DM_PER_WRITE_GROUP (RW_MGR_TRUE_MEM_DATA_MASK_WIDTH \
 	/ RW_MGR_MEM_IF_WRITE_DQS_WIDTH)

 #define RW_MGR_NUM_DQS_PER_WRITE_GROUP (RW_MGR_MEM_IF_READ_DQS_WIDTH \
 	/ RW_MGR_MEM_IF_WRITE_DQS_WIDTH)
 #define NUM_RANKS_PER_SHADOW_REG (RW_MGR_MEM_NUMBER_OF_RANKS / NUM_SHADOW_REGS)

 #define RW_MGR_RUN_SINGLE_GROUP_OFFSET		0x0
 #define RW_MGR_RUN_ALL_GROUPS_OFFSET		0x0400
 #define RW_MGR_RESET_READ_DATAPATH_OFFSET	0x1000
 #define RW_MGR_SET_CS_AND_ODT_MASK_OFFSET	0x1400
 #define RW_MGR_INST_ROM_WRITE_OFFSET		0x1800
 #define RW_MGR_AC_ROM_WRITE_OFFSET		0x1C00

 #define RW_MGR_MEM_NUMBER_OF_RANKS	1
 #define NUM_SHADOW_REGS			1

 #define RW_MGR_RANK_NONE		0xFF
 #define RW_MGR_RANK_ALL			0x00

 #define RW_MGR_ODT_MODE_OFF		0
 #define RW_MGR_ODT_MODE_READ_WRITE	1

 #define NUM_CALIB_REPEAT		1

 #define NUM_READ_TESTS			7
 #define NUM_READ_PB_TESTS		7
 #define NUM_WRITE_TESTS			15
 #define NUM_WRITE_PB_TESTS		31

 #define PASS_ALL_BITS			1
 #define PASS_ONE_BIT			0

 /* calibration stages */
 #define CAL_STAGE_NIL			0
 #define CAL_STAGE_VFIFO			1
 #define CAL_STAGE_WLEVEL		2
 #define CAL_STAGE_LFIFO			3
 #define CAL_STAGE_WRITES		4
 #define CAL_STAGE_FULLTEST		5
 #define CAL_STAGE_REFRESH		6
 #define CAL_STAGE_CAL_SKIPPED		7
 #define CAL_STAGE_CAL_ABORTED		8
 #define CAL_STAGE_VFIFO_AFTER_WRITES	9

 /* calibration substages */
 #define CAL_SUBSTAGE_NIL		0
 #define CAL_SUBSTAGE_GUARANTEED_READ	1
 #define CAL_SUBSTAGE_DQS_EN_PHASE	2
 #define CAL_SUBSTAGE_VFIFO_CENTER	3
 #define CAL_SUBSTAGE_WORKING_DELAY	1
 #define CAL_SUBSTAGE_LAST_WORKING_DELAY	2
 #define CAL_SUBSTAGE_WLEVEL_COPY	3
 #define CAL_SUBSTAGE_WRITES_CENTER	1
 #define CAL_SUBSTAGE_READ_LATENCY	1
 #define CAL_SUBSTAGE_REFRESH		1

 #define MAX_RANKS			(RW_MGR_MEM_NUMBER_OF_RANKS)
 #define MAX_DQS				(RW_MGR_MEM_IF_WRITE_DQS_WIDTH > \
 					RW_MGR_MEM_IF_READ_DQS_WIDTH ? \
 					RW_MGR_MEM_IF_WRITE_DQS_WIDTH : \
 					RW_MGR_MEM_IF_READ_DQS_WIDTH)
 #define MAX_DQ				(RW_MGR_MEM_DATA_WIDTH)
 #define MAX_DM				(RW_MGR_MEM_DATA_MASK_WIDTH)

 /* length of VFIFO, from SW_MACROS */
 #define VFIFO_SIZE			(READ_VALID_FIFO_SIZE)

 #define SCC_MGR_GROUP_COUNTER_OFFSET		0x0000
 #define SCC_MGR_DQS_IN_DELAY_OFFSET		0x0100
 #define SCC_MGR_DQS_EN_PHASE_OFFSET		0x0200
 #define SCC_MGR_DQS_EN_DELAY_OFFSET		0x0300
 #define SCC_MGR_DQDQS_OUT_PHASE_OFFSET		0x0400
 #define SCC_MGR_OCT_OUT1_DELAY_OFFSET		0x0500
 #define SCC_MGR_IO_OUT1_DELAY_OFFSET		0x0700
 #define SCC_MGR_IO_IN_DELAY_OFFSET		0x0900

 /* HHP-HPS-specific versions of some commands */
 #define SCC_MGR_DQS_EN_DELAY_GATE_OFFSET	0x0600
 #define SCC_MGR_IO_OE_DELAY_OFFSET		0x0800
 #define SCC_MGR_HHP_GLOBALS_OFFSET		0x0A00
 #define SCC_MGR_HHP_RFILE_OFFSET		0x0B00
 #define SCC_MGR_AFI_CAL_INIT_OFFSET		0x0D00

 #define SDR_PHYGRP_SCCGRP_ADDRESS		(SOCFPGA_SDR_ADDRESS | 0x0)
 #define SDR_PHYGRP_PHYMGRGRP_ADDRESS		(SOCFPGA_SDR_ADDRESS | 0x1000)
 #define SDR_PHYGRP_RWMGRGRP_ADDRESS		(SOCFPGA_SDR_ADDRESS | 0x2000)
 #define SDR_PHYGRP_DATAMGRGRP_ADDRESS		(SOCFPGA_SDR_ADDRESS | 0x4000)
 #define SDR_PHYGRP_REGFILEGRP_ADDRESS		(SOCFPGA_SDR_ADDRESS | 0x4800)

 #define PHY_MGR_CAL_RESET		(0)
 #define PHY_MGR_CAL_SUCCESS		(1)
 #define PHY_MGR_CAL_FAIL		(2)

 #define CALIB_SKIP_DELAY_LOOPS		(1 << 0)
 #define CALIB_SKIP_ALL_BITS_CHK		(1 << 1)
 #define CALIB_SKIP_DELAY_SWEEPS		(1 << 2)
 #define CALIB_SKIP_VFIFO		(1 << 3)
 #define CALIB_SKIP_LFIFO		(1 << 4)
 #define CALIB_SKIP_WLEVEL		(1 << 5)
 #define CALIB_SKIP_WRITES		(1 << 6)
 #define CALIB_SKIP_FULL_TEST		(1 << 7)
 #define CALIB_SKIP_ALL			(CALIB_SKIP_VFIFO | \
 				CALIB_SKIP_LFIFO | CALIB_SKIP_WLEVEL | \
 				CALIB_SKIP_WRITES | CALIB_SKIP_FULL_TEST)
 #define CALIB_IN_RTL_SIM			(1 << 8)

 /* Scan chain manager command addresses */
 #define READ_SCC_OCT_OUT2_DELAY			0
 #define READ_SCC_DQ_OUT2_DELAY			0
 #define READ_SCC_DQS_IO_OUT2_DELAY		0
 #define READ_SCC_DM_IO_OUT2_DELAY		0

 /* HHP-HPS-specific values */
 #define SCC_MGR_HHP_EXTRAS_OFFSET			0
 #define SCC_MGR_HHP_DQSE_MAP_OFFSET			1

 /* PHY Debug mode flag constants */
 #define PHY_DEBUG_IN_DEBUG_MODE 0x00000001
 #define PHY_DEBUG_ENABLE_CAL_RPT 0x00000002
 #define PHY_DEBUG_ENABLE_MARGIN_RPT 0x00000004
 #define PHY_DEBUG_SWEEP_ALL_GROUPS 0x00000008
 #define PHY_DEBUG_DISABLE_GUARANTEED_READ 0x00000010
 #define PHY_DEBUG_ENABLE_NON_DESTRUCTIVE_CALIBRATION 0x00000020

 /* Init and Reset delay constants - Only use if defined by sequencer_defines.h,
  * otherwise, revert to defaults
  * Default for Tinit = (0+1) * ((202+1) * (2 * 131 + 1) + 1) = 53532 =
  * 200.75us @ 266MHz
  */
 #ifdef TINIT_CNTR0_VAL
 #define SEQ_TINIT_CNTR0_VAL TINIT_CNTR0_VAL
 #else
 #define SEQ_TINIT_CNTR0_VAL 0
 #endif

 #ifdef TINIT_CNTR1_VAL
 #define SEQ_TINIT_CNTR1_VAL TINIT_CNTR1_VAL
 #else
 #define SEQ_TINIT_CNTR1_VAL 202
 #endif

 #ifdef TINIT_CNTR2_VAL
 #define SEQ_TINIT_CNTR2_VAL TINIT_CNTR2_VAL
 #else
 #define SEQ_TINIT_CNTR2_VAL 131
 #endif


 /* Default for Treset = (2+1) * ((252+1) * (2 * 131 + 1) + 1) = 133563 =
  * 500.86us @ 266MHz
  */
 #ifdef TRESET_CNTR0_VAL
 #define SEQ_TRESET_CNTR0_VAL TRESET_CNTR0_VAL
 #else
 #define SEQ_TRESET_CNTR0_VAL 2
 #endif

 #ifdef TRESET_CNTR1_VAL
 #define SEQ_TRESET_CNTR1_VAL TRESET_CNTR1_VAL
 #else
 #define SEQ_TRESET_CNTR1_VAL 252
 #endif

 #ifdef TRESET_CNTR2_VAL
 #define SEQ_TRESET_CNTR2_VAL TRESET_CNTR2_VAL
 #else
 #define SEQ_TRESET_CNTR2_VAL 131
 #endif

 struct socfpga_sdr_rw_load_manager {
 	u32	load_cntr0;
 	u32	load_cntr1;
 	u32	load_cntr2;
 	u32	load_cntr3;
 };

 struct socfpga_sdr_rw_load_jump_manager {
 	u32	load_jump_add0;
 	u32	load_jump_add1;
 	u32	load_jump_add2;
 	u32	load_jump_add3;
 };

 struct socfpga_sdr_reg_file {
 	u32 signature;
 	u32 debug_data_addr;
 	u32 cur_stage;
 	u32 fom;
 	u32 failing_stage;
 	u32 debug1;
 	u32 debug2;
 	u32 dtaps_per_ptap;
 	u32 trk_sample_count;
 	u32 trk_longidle;
 	u32 delays;
 	u32 trk_rw_mgr_addr;
 	u32 trk_read_dqs_width;
 	u32 trk_rfsh;
 };

 /* parameter variable holder */
 struct param_type {
 	uint32_t dm_correct_mask;
 	uint32_t read_correct_mask;
 	uint32_t read_correct_mask_vg;
 	uint32_t write_correct_mask;
 	uint32_t write_correct_mask_vg;

 	/* set a particular entry to 1 if we need to skip a particular rank */

 	uint32_t skip_ranks[MAX_RANKS];

 	/* set a particular entry to 1 if we need to skip a particular group */

 	uint32_t skip_groups;

 	/* set a particular entry to 1 if the shadow register
 	(which represents a set of ranks) needs to be skipped */

 	uint32_t skip_shadow_regs[NUM_SHADOW_REGS];

 };


 /* global variable holder */
 struct gbl_type {
 	uint32_t phy_debug_mode_flags;

 	/* current read latency */

 	uint32_t curr_read_lat;

 	/* error code */

 	uint32_t error_substage;
 	uint32_t error_stage;
 	uint32_t error_group;

 	/* figure-of-merit in, figure-of-merit out */

 	uint32_t fom_in;
 	uint32_t fom_out;

 	/*USER Number of RW Mgr NOP cycles between
 	write command and write data */
 	uint32_t rw_wl_nop_cycles;
 };

 struct socfpga_sdr_scc_mgr {
 	u32	dqs_ena;
 	u32	dqs_io_ena;
 	u32	dq_ena;
 	u32	dm_ena;
 	u32	__padding1[4];
 	u32	update;
 	u32	__padding2[7];
 	u32	active_rank;
 };

 /* PHY manager configuration registers. */
 struct socfpga_phy_mgr_cfg {
 	u32	phy_rlat;
 	u32	reset_mem_stbl;
 	u32	mux_sel;
 	u32	cal_status;
 	u32	cal_debug_info;
 	u32	vfifo_rd_en_ovrd;
 	u32	afi_wlat;
 	u32	afi_rlat;
 };

 /* PHY manager command addresses. */
 struct socfpga_phy_mgr_cmd {
 	u32	inc_vfifo_fr;
 	u32	inc_vfifo_hard_phy;
 	u32	fifo_reset;
 	u32	inc_vfifo_fr_hr;
 	u32	inc_vfifo_qr;
 };

 struct socfpga_data_mgr {
 	u32	__padding1;
 	u32	t_wl_add;
 	u32	mem_t_add;
 	u32	t_rl_add;
 };
 #endif /* _SEQUENCER_H_ */
	/*
	* Copyright Altera Corporation (C) 2012-2015
	*
	* SPDX-License-Identifier: BSD-3-Clause
	*/

	#ifndef _SEQUENCER_H_
	#define _SEQUENCER_H_

	#define RW_MGR_NUM_DM_PER_WRITE_GROUP (RW_MGR_MEM_DATA_MASK_WIDTH \
	/ RW_MGR_MEM_IF_WRITE_DQS_WIDTH)
	#define RW_MGR_NUM_TRUE_DM_PER_WRITE_GROUP (RW_MGR_TRUE_MEM_DATA_MASK_WIDTH \
	/ RW_MGR_MEM_IF_WRITE_DQS_WIDTH)

	#define RW_MGR_NUM_DQS_PER_WRITE_GROUP (RW_MGR_MEM_IF_READ_DQS_WIDTH \
	/ RW_MGR_MEM_IF_WRITE_DQS_WIDTH)
	#define NUM_RANKS_PER_SHADOW_REG (RW_MGR_MEM_NUMBER_OF_RANKS / NUM_SHADOW_REGS)

	#define RW_MGR_RUN_SINGLE_GROUP_OFFSET 0x0
	#define RW_MGR_RUN_ALL_GROUPS_OFFSET 0x0400
	#define RW_MGR_RESET_READ_DATAPATH_OFFSET 0x1000
	#define RW_MGR_SET_CS_AND_ODT_MASK_OFFSET 0x1400
	#define RW_MGR_INST_ROM_WRITE_OFFSET 0x1800
	#define RW_MGR_AC_ROM_WRITE_OFFSET 0x1C00

	#define RW_MGR_MEM_NUMBER_OF_RANKS 1
	#define NUM_SHADOW_REGS 1

	#define RW_MGR_RANK_NONE 0xFF
	#define RW_MGR_RANK_ALL 0x00

	#define RW_MGR_ODT_MODE_OFF 0
	#define RW_MGR_ODT_MODE_READ_WRITE 1

	#define NUM_CALIB_REPEAT 1

	#define NUM_READ_TESTS 7
	#define NUM_READ_PB_TESTS 7
	#define NUM_WRITE_TESTS 15
	#define NUM_WRITE_PB_TESTS 31

	#define PASS_ALL_BITS 1
	#define PASS_ONE_BIT 0

	/* calibration stages */
	#define CAL_STAGE_NIL 0
	#define CAL_STAGE_VFIFO 1
	#define CAL_STAGE_WLEVEL 2
	#define CAL_STAGE_LFIFO 3
	#define CAL_STAGE_WRITES 4
	#define CAL_STAGE_FULLTEST 5
	#define CAL_STAGE_REFRESH 6
	#define CAL_STAGE_CAL_SKIPPED 7
	#define CAL_STAGE_CAL_ABORTED 8
	#define CAL_STAGE_VFIFO_AFTER_WRITES 9

	/* calibration substages */
	#define CAL_SUBSTAGE_NIL 0
	#define CAL_SUBSTAGE_GUARANTEED_READ 1
	#define CAL_SUBSTAGE_DQS_EN_PHASE 2
	#define CAL_SUBSTAGE_VFIFO_CENTER 3
	#define CAL_SUBSTAGE_WORKING_DELAY 1
	#define CAL_SUBSTAGE_LAST_WORKING_DELAY 2
	#define CAL_SUBSTAGE_WLEVEL_COPY 3
	#define CAL_SUBSTAGE_WRITES_CENTER 1
	#define CAL_SUBSTAGE_READ_LATENCY 1
	#define CAL_SUBSTAGE_REFRESH 1

	#define MAX_RANKS (RW_MGR_MEM_NUMBER_OF_RANKS)
	#define MAX_DQS (RW_MGR_MEM_IF_WRITE_DQS_WIDTH > \
	RW_MGR_MEM_IF_READ_DQS_WIDTH ? \
	RW_MGR_MEM_IF_WRITE_DQS_WIDTH : \
	RW_MGR_MEM_IF_READ_DQS_WIDTH)
	#define MAX_DQ (RW_MGR_MEM_DATA_WIDTH)
	#define MAX_DM (RW_MGR_MEM_DATA_MASK_WIDTH)

	/* length of VFIFO, from SW_MACROS */
	#define VFIFO_SIZE (READ_VALID_FIFO_SIZE)

	#define SCC_MGR_GROUP_COUNTER_OFFSET 0x0000
	#define SCC_MGR_DQS_IN_DELAY_OFFSET 0x0100
	#define SCC_MGR_DQS_EN_PHASE_OFFSET 0x0200
	#define SCC_MGR_DQS_EN_DELAY_OFFSET 0x0300
	#define SCC_MGR_DQDQS_OUT_PHASE_OFFSET 0x0400
	#define SCC_MGR_OCT_OUT1_DELAY_OFFSET 0x0500
	#define SCC_MGR_IO_OUT1_DELAY_OFFSET 0x0700
	#define SCC_MGR_IO_IN_DELAY_OFFSET 0x0900

	/* HHP-HPS-specific versions of some commands */
	#define SCC_MGR_DQS_EN_DELAY_GATE_OFFSET 0x0600
	#define SCC_MGR_IO_OE_DELAY_OFFSET 0x0800
	#define SCC_MGR_HHP_GLOBALS_OFFSET 0x0A00
	#define SCC_MGR_HHP_RFILE_OFFSET 0x0B00
	#define SCC_MGR_AFI_CAL_INIT_OFFSET 0x0D00

	#define SDR_PHYGRP_SCCGRP_ADDRESS (SOCFPGA_SDR_ADDRESS \| 0x0)
	#define SDR_PHYGRP_PHYMGRGRP_ADDRESS (SOCFPGA_SDR_ADDRESS \| 0x1000)
	#define SDR_PHYGRP_RWMGRGRP_ADDRESS (SOCFPGA_SDR_ADDRESS \| 0x2000)
	#define SDR_PHYGRP_DATAMGRGRP_ADDRESS (SOCFPGA_SDR_ADDRESS \| 0x4000)
	#define SDR_PHYGRP_REGFILEGRP_ADDRESS (SOCFPGA_SDR_ADDRESS \| 0x4800)

	#define PHY_MGR_CAL_RESET (0)
	#define PHY_MGR_CAL_SUCCESS (1)
	#define PHY_MGR_CAL_FAIL (2)

	#define CALIB_SKIP_DELAY_LOOPS (1 << 0)
	#define CALIB_SKIP_ALL_BITS_CHK (1 << 1)
	#define CALIB_SKIP_DELAY_SWEEPS (1 << 2)
	#define CALIB_SKIP_VFIFO (1 << 3)
	#define CALIB_SKIP_LFIFO (1 << 4)
	#define CALIB_SKIP_WLEVEL (1 << 5)
	#define CALIB_SKIP_WRITES (1 << 6)
	#define CALIB_SKIP_FULL_TEST (1 << 7)
	#define CALIB_SKIP_ALL (CALIB_SKIP_VFIFO \| \
	CALIB_SKIP_LFIFO \| CALIB_SKIP_WLEVEL \| \
	CALIB_SKIP_WRITES \| CALIB_SKIP_FULL_TEST)
	#define CALIB_IN_RTL_SIM (1 << 8)

	/* Scan chain manager command addresses */
	#define READ_SCC_OCT_OUT2_DELAY 0
	#define READ_SCC_DQ_OUT2_DELAY 0
	#define READ_SCC_DQS_IO_OUT2_DELAY 0
	#define READ_SCC_DM_IO_OUT2_DELAY 0

	/* HHP-HPS-specific values */
	#define SCC_MGR_HHP_EXTRAS_OFFSET 0
	#define SCC_MGR_HHP_DQSE_MAP_OFFSET 1

	/* PHY Debug mode flag constants */
	#define PHY_DEBUG_IN_DEBUG_MODE 0x00000001
	#define PHY_DEBUG_ENABLE_CAL_RPT 0x00000002
	#define PHY_DEBUG_ENABLE_MARGIN_RPT 0x00000004
	#define PHY_DEBUG_SWEEP_ALL_GROUPS 0x00000008
	#define PHY_DEBUG_DISABLE_GUARANTEED_READ 0x00000010
	#define PHY_DEBUG_ENABLE_NON_DESTRUCTIVE_CALIBRATION 0x00000020

	/* Init and Reset delay constants - Only use if defined by sequencer_defines.h,
	* otherwise, revert to defaults
	* Default for Tinit = (0+1) * ((202+1) * (2 * 131 + 1) + 1) = 53532 =
	* 200.75us @ 266MHz
	*/
	#ifdef TINIT_CNTR0_VAL
	#define SEQ_TINIT_CNTR0_VAL TINIT_CNTR0_VAL
	#else
	#define SEQ_TINIT_CNTR0_VAL 0
	#endif

	#ifdef TINIT_CNTR1_VAL
	#define SEQ_TINIT_CNTR1_VAL TINIT_CNTR1_VAL
	#else
	#define SEQ_TINIT_CNTR1_VAL 202
	#endif

	#ifdef TINIT_CNTR2_VAL
	#define SEQ_TINIT_CNTR2_VAL TINIT_CNTR2_VAL
	#else
	#define SEQ_TINIT_CNTR2_VAL 131
	#endif


	/* Default for Treset = (2+1) * ((252+1) * (2 * 131 + 1) + 1) = 133563 =
	* 500.86us @ 266MHz
	*/
	#ifdef TRESET_CNTR0_VAL
	#define SEQ_TRESET_CNTR0_VAL TRESET_CNTR0_VAL
	#else
	#define SEQ_TRESET_CNTR0_VAL 2
	#endif

	#ifdef TRESET_CNTR1_VAL
	#define SEQ_TRESET_CNTR1_VAL TRESET_CNTR1_VAL
	#else
	#define SEQ_TRESET_CNTR1_VAL 252
	#endif

	#ifdef TRESET_CNTR2_VAL
	#define SEQ_TRESET_CNTR2_VAL TRESET_CNTR2_VAL
	#else
	#define SEQ_TRESET_CNTR2_VAL 131
	#endif

	struct socfpga_sdr_rw_load_manager {
	u32 load_cntr0;
	u32 load_cntr1;
	u32 load_cntr2;
	u32 load_cntr3;
	};

	struct socfpga_sdr_rw_load_jump_manager {
	u32 load_jump_add0;
	u32 load_jump_add1;
	u32 load_jump_add2;
	u32 load_jump_add3;
	};

	struct socfpga_sdr_reg_file {
	u32 signature;
	u32 debug_data_addr;
	u32 cur_stage;
	u32 fom;
	u32 failing_stage;
	u32 debug1;
	u32 debug2;
	u32 dtaps_per_ptap;
	u32 trk_sample_count;
	u32 trk_longidle;
	u32 delays;
	u32 trk_rw_mgr_addr;
	u32 trk_read_dqs_width;
	u32 trk_rfsh;
	};

	/* parameter variable holder */
	struct param_type {
	uint32_t dm_correct_mask;
	uint32_t read_correct_mask;
	uint32_t read_correct_mask_vg;
	uint32_t write_correct_mask;
	uint32_t write_correct_mask_vg;

	/* set a particular entry to 1 if we need to skip a particular rank */

	uint32_t skip_ranks[MAX_RANKS];

	/* set a particular entry to 1 if we need to skip a particular group */

	uint32_t skip_groups;

	/* set a particular entry to 1 if the shadow register
	(which represents a set of ranks) needs to be skipped */

	uint32_t skip_shadow_regs[NUM_SHADOW_REGS];

	};


	/* global variable holder */
	struct gbl_type {
	uint32_t phy_debug_mode_flags;

	/* current read latency */

	uint32_t curr_read_lat;

	/* error code */

	uint32_t error_substage;
	uint32_t error_stage;
	uint32_t error_group;

	/* figure-of-merit in, figure-of-merit out */

	uint32_t fom_in;
	uint32_t fom_out;

	/*USER Number of RW Mgr NOP cycles between
	write command and write data */
	uint32_t rw_wl_nop_cycles;
	};

	struct socfpga_sdr_scc_mgr {
	u32 dqs_ena;
	u32 dqs_io_ena;
	u32 dq_ena;
	u32 dm_ena;
	u32 __padding1[4];
	u32 update;
	u32 __padding2[7];
	u32 active_rank;
	};

	/* PHY manager configuration registers. */
	struct socfpga_phy_mgr_cfg {
	u32 phy_rlat;
	u32 reset_mem_stbl;
	u32 mux_sel;
	u32 cal_status;
	u32 cal_debug_info;
	u32 vfifo_rd_en_ovrd;
	u32 afi_wlat;
	u32 afi_rlat;
	};

	/* PHY manager command addresses. */
	struct socfpga_phy_mgr_cmd {
	u32 inc_vfifo_fr;
	u32 inc_vfifo_hard_phy;
	u32 fifo_reset;
	u32 inc_vfifo_fr_hr;
	u32 inc_vfifo_qr;
	};

	struct socfpga_data_mgr {
	u32 __padding1;
	u32 t_wl_add;
	u32 mem_t_add;
	u32 t_rl_add;
	};
	#endif /* _SEQUENCER_H_ */