| T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC. |
| It can work in two mode: standalone mode and PCIe endpoint mode. |
| |
| T2080 SoC Overview |
| ------------------ |
| The T2080 QorIQ multicore processor combines four dual-threaded e6500 Power |
| Architecture processor cores with high-performance datapath acceleration |
| logic and network and peripheral bus interfaces required for networking, |
| telecom/datacom, wireless infrastructure, and mil/aerospace applications. |
| |
| T2080 includes the following functions and features: |
| - Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz |
| - 2MB L2 cache and 512KB CoreNet platform cache (CPC) |
| - Hierarchical interconnect fabric |
| - One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving |
| - Data Path Acceleration Architecture (DPAA) incorporating acceleration |
| - 16 SerDes lanes up to 10.3125 GHz |
| - 8 Ethernet interfaces, supporting combinations of the following: |
| - Up to four 10 Gbps Ethernet MACs |
| - Up to eight 1 Gbps Ethernet MACs |
| - Up to four 2.5 Gbps Ethernet MACs |
| - High-speed peripheral interfaces |
| - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) |
| - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz |
| - Additional peripheral interfaces |
| - Two serial ATA (SATA 2.0) controllers |
| - Two high-speed USB 2.0 controllers with integrated PHY |
| - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC) |
| - Enhanced serial peripheral interface (eSPI) |
| - Four I2C controllers |
| - Four 2-pin UARTs or two 4-pin UARTs |
| - Integrated Flash Controller supporting NAND and NOR flash |
| - Three eight-channel DMA engines |
| - Support for hardware virtualization and partitioning enforcement |
| - QorIQ Platform's Trust Architecture 2.0 |
| |
| Differences between T2080 and T2081 |
| ----------------------------------- |
| Feature T2080 T2081 |
| 1G Ethernet numbers: 8 6 |
| 10G Ethernet numbers: 4 2 |
| SerDes lanes: 16 8 |
| Serial RapidIO,RMan: 2 no |
| SATA Controller: 2 no |
| Aurora: yes no |
| SoC Package: 896-pins 780-pins |
| |
| |
| T2080PCIe-RDB board Overview |
| ---------------------------- |
| - SERDES Configuration |
| - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10) |
| - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2) |
| - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3) |
| - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2) |
| - SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2) |
| - SerDes-2 Lane G-H: to SATA1 & SATA2 |
| - Ethernet |
| - Two on-board 10M/100M/1G RGMII ethernet ports |
| - Two on-board 10Gbps XFI fiber ports |
| - Two on-board 10Gbps Base-T copper ports |
| - DDR Memory |
| - Supports 72bit 4GB DDR3-LP SODIMM |
| - PCIe |
| - One PCIe x4 gold-finger |
| - One PCIe x4 connector |
| - One PCIe x2 end-point device (C293 Crypto co-processor) |
| - IFC/Local Bus |
| - NOR: 128MB 16-bit NOR Flash |
| - NAND: 1GB 8-bit NAND flash |
| - CPLD: for system controlling with programable header on-board |
| - SATA |
| - Two SATA 2.0 onnectors on-board |
| - USB |
| - Supports two USB 2.0 ports with integrated PHYs |
| - Two type A ports with 5V@1.5A per port. |
| - SDHC |
| - one TF-card connector on-board |
| - SPI |
| - On-board 64MB SPI flash |
| - Other |
| - Two Serial ports |
| - Four I2C ports |
| |
| |
| System Memory map |
| ----------------- |
| Start Address End Address Description Size |
| 0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB |
| 0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB |
| 0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB |
| 0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB |
| 0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB |
| 0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB |
| 0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB |
| 0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB |
| 0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB |
| 0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB |
| 0xF_0000_0000 0xF_003F_FFFF DCSR 4MB |
| 0xC_4000_0000 0xC_4FFF_FFFF PCI Express 4 Mem Space 256MB |
| 0xC_3000_0000 0xC_3FFF_FFFF PCI Express 3 Mem Space 256MB |
| 0xC_2000_0000 0xC_2FFF_FFFF PCI Express 2 Mem Space 256MB |
| 0xC_0000_0000 0xC_1FFF_FFFF PCI Express 1 Mem Space 512MB |
| 0x0_0000_0000 0x0_ffff_ffff DDR 4GB |
| |
| |
| 128M NOR Flash memory Map |
| ------------------------- |
| Start Address End Address Definition Max size |
| 0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB |
| 0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB |
| 0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB |
| 0xEFE00000 0xEFE3FFFF PHY CS4315 firmware 256KB |
| 0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB |
| 0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB |
| 0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB |
| 0xEC000000 0xEC01FFFF RCW (alt bank) 128KB |
| 0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB |
| 0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB |
| 0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB |
| 0xEBE00000 0xEBE3FFFF PHY CS4315 firmware (alt bank) 256KB |
| 0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB |
| 0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB |
| 0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB |
| 0xE8000000 0xE801FFFF RCW (current bank) 128KB |
| |
| |
| T2080PCIe-RDB Ethernet Port Map |
| ------------------------------- |
| Label In Uboot In Linux FMan Address Comments PHY |
| ETH0 FM1@GTEC1 fm1-mac9 0xfe4f0000 10G SFP+ (CS4315) |
| ETH1 FM1@GTEC2 fm1-mac10 0xfe4f2000 10G SFP+ (CS4315) |
| ETH2 FM1@GTEC3 fm1-mac1 0xfe4e0000 10G Base-T (AQ1202) |
| ETH3 FM1@GTEC4 fm1-mac2 0xfe4e2000 10G Base-T (AQ1202) |
| ETH4 FM1@DTSEC3 fm1-mac3 0xfe4e4000 1G RGMII (RTL8211E) |
| ETH5 FM1@DTSEC4 fm1-mac4 0xfe4e6000 1G RGMII (RTL8211E) |
| |
| |
| T2080PCIe-RDB Default DIP-Switch setting |
| ---------------------------------------- |
| SW1[1:8] = '00010011' |
| SW2[1:8] = '10111111' |
| SW3[1:8] = '11100001' |
| |
| Software configurations and board settings |
| ------------------------------------------ |
| 1. NOR boot: |
| a. build NOR boot image |
| $ make T2080RDB_config |
| $ make |
| b. program u-boot.bin image to NOR flash |
| => tftp 1000000 u-boot.bin |
| => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize |
| set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot |
| |
| Switching between default bank and alternate bank on NOR flash |
| To change boot source to vbank4: |
| via software: run command 'cpld reset altbank' in U-Boot. |
| via DIP-switch: set SW3[5:7] = '100' |
| |
| To change boot source to vbank0: |
| via software: run command 'cpld reset' in U-Boot. |
| via DIP-Switch: set SW3[5:7] = '000' |
| |
| 2. NAND Boot: |
| a. build PBL image for NAND boot |
| $ make T2080RDB_NAND_config |
| $ make |
| b. program u-boot-with-spl-pbl.bin to NAND flash |
| => tftp 1000000 u-boot-with-spl-pbl.bin |
| => nand erase 0 d0000 |
| => nand write 1000000 0 $filesize |
| set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot |
| |
| 3. SPI Boot: |
| a. build PBL image for SPI boot |
| $ make T2080RDB_SPIFLASH_config |
| $ make |
| b. program u-boot-with-spl-pbl.bin to SPI flash |
| => tftp 1000000 u-boot-with-spl-pbl.bin |
| => sf probe 0 |
| => sf erase 0 d0000 |
| => sf write 1000000 0 $filesize |
| set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot |
| |
| 4. SD Boot: |
| a. build PBL image for SD boot |
| $ make T2080RDB_SDCARD_config |
| $ make |
| b. program u-boot-with-spl-pbl.bin to micro-SD/TF card |
| => tftp 1000000 u-boot-with-spl-pbl.bin |
| => mmc write 1000000 8 0x800 |
| set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot |
| |
| |
| 2-stage NAND/SPI/SD boot loader |
| ------------------------------- |
| PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. |
| SPL further initializes DDR using SPD and environment variables |
| and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR. |
| Finally SPL transers control to U-Boot for futher booting. |
| |
| SPL has following features: |
| - Executes within 256K |
| - No relocation required |
| |
| Run time view of SPL framework |
| ------------------------------------------------- |
| |Area | Address | |
| ------------------------------------------------- |
| |SecureBoot header | 0xFFFC0000 (32KB) | |
| ------------------------------------------------- |
| |GD, BD | 0xFFFC8000 (4KB) | |
| ------------------------------------------------- |
| |ENV | 0xFFFC9000 (8KB) | |
| ------------------------------------------------- |
| |HEAP | 0xFFFCB000 (50KB) | |
| ------------------------------------------------- |
| |STACK | 0xFFFD8000 (22KB) | |
| ------------------------------------------------- |
| |U-Boot SPL | 0xFFFD8000 (160KB) | |
| ------------------------------------------------- |
| |
| NAND Flash memory Map on T2080RDB |
| -------------------------------------------------------------- |
| Start End Definition Size |
| 0x000000 0x0FFFFF U-Boot img 1MB (2 blocks) |
| 0x100000 0x17FFFF U-Boot env 512KB (1 block) |
| 0x180000 0x1FFFFF FMAN ucode 512KB (1 block) |
| 0x200000 0x27FFFF CS4315 ucode 512KB (1 block) |
| |
| |
| Micro SD Card memory Map on T2080RDB |
| ---------------------------------------------------- |
| Block #blocks Definition Size |
| 0x008 2048 U-Boot img 1MB |
| 0x800 0016 U-Boot env 8KB |
| 0x820 0128 FMAN ucode 64KB |
| 0x8a0 0512 CS4315 ucode 256KB |
| |
| |
| SPI Flash memory Map on T2080RDB |
| ---------------------------------------------------- |
| Start End Definition Size |
| 0x000000 0x0FFFFF U-Boot img 1MB |
| 0x100000 0x101FFF U-Boot env 8KB |
| 0x110000 0x11FFFF FMAN ucode 64KB |
| 0x120000 0x15FFFF CS4315 ucode 256KB |
| |
| |
| How to update the ucode of Cortina CS4315/CS4340 10G PHY |
| -------------------------------------------------------- |
| => tftp 1000000 CS4315-CS4340-PHY-ucode.txt |
| => pro off all;era 0xefe00000 0xefefffff;cp.b 1000000 0xefe00000 $filesize |
| |
| |
| How to update the ucode of Freescale FMAN |
| ----------------------------------------- |
| => tftp 1000000 fsl_fman_ucode_t2080_r1.0.bin |
| => pro off all;erase 0xeff00000 0xeff1ffff;cp 1000000 0xeff00000 $filesize |
| |
| |
| For more details, please refer to T2080PCIe-RDB User Guide and access |
| website www.freescale.com and Freescale QorIQ SDK Infocenter document. |