include/configs/v38b.h - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2003-2006 Wolfgang Denk, DENX Software Engineering,
  * wd@denx.de.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */
 #define CONFIG_MPC5200			1	/* This is an MPC5200 CPU */
 #define CONFIG_V38B			1	/* ...on V38B board */

 #define	CONFIG_SYS_TEXT_BASE		0xFF000000

 #define CONFIG_SYS_MPC5XXX_CLKIN	33000000	/* ...running at 33.000000MHz */

 #define CONFIG_RTC_PCF8563		1	/* has PCF8563 RTC */
 #define CONFIG_MPC5200_DDR		1	/* has DDR SDRAM */

 #undef CONFIG_HW_WATCHDOG			/* don't use watchdog */

 #define CONFIG_NETCONSOLE		1

 #define CONFIG_BOARD_EARLY_INIT_R	1	/* do board-specific init */
 #define CONFIG_BOARD_EARLY_INIT_F	1	/* do board-specific init */
 #define CONFIG_MISC_INIT_R

 #define CONFIG_SYS_XLB_PIPELINING		1	/* gives better performance */

 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 /*
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
 #define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 /*
  * DDR
  */
 #define SDRAM_DDR		1	/* is DDR */
 /* Settings for XLB = 132 MHz */
 #define SDRAM_MODE		0x018D0000
 #define SDRAM_EMODE		0x40090000
 #define SDRAM_CONTROL		0x704f0f00
 #define SDRAM_CONFIG1		0x73722930
 #define SDRAM_CONFIG2		0x47770000
 #define SDRAM_TAPDELAY		0x10000000

 /*
  * PCI - no suport
  */
 #undef CONFIG_PCI

 /*
  * Partitions
  */
 #define CONFIG_MAC_PARTITION	1
 #define CONFIG_DOS_PARTITION	1

 /*
  * USB
  */
 #define CONFIG_USB_OHCI
 #define CONFIG_USB_STORAGE
 #define CONFIG_USB_CLOCK	0x0001BBBB
 #define CONFIG_USB_CONFIG	0x00001000


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_USB
 #define CONFIG_CMD_FAT


 #define CONFIG_TIMESTAMP		/* Print image info with timestamp */

 /*
  * Boot low with 16 MB Flash
  */
 #define CONFIG_SYS_LOWBOOT		1
 #define CONFIG_SYS_LOWBOOT16		1

 /*
  * Autobooting
  */
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds */

 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"

 #undef CONFIG_BOOTARGS

 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"bootcmd=run net_nfs\0"						\
 	"bootdelay=3\0"							\
 	"baudrate=115200\0"						\
 	"preboot=echo;echo Type \"run flash_nfs\" to mount root "	\
 		"filesystem over NFS; echo\0"				\
 	"netdev=eth0\0"							\
 	"ramargs=setenv bootargs root=/dev/ram rw wdt=off \0"		\
 	"addip=setenv bootargs $(bootargs) "				\
 		"ip=$(ipaddr):$(serverip):$(gatewayip):"		\
 		"$(netmask):$(hostname):$(netdev):off panic=1\0"	\
 	"flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0"		\
 	"flash_self=run ramargs addip;bootm $(kernel_addr) "		\
 		"$(ramdisk_addr)\0"					\
 	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0"	\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=$(serverip):$(rootpath) wdt=off\0"		\
 	"hostname=v38b\0"						\
 	"ethact=FEC\0"							\
 	"rootpath=/opt/eldk-3.1.1/ppc_6xx\0"				\
 	"update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; "	\
 		"cp.b 200000 ff000000 $(filesize);"			\
 		"prot on ff000000 ff03ffff\0"				\
 	"load=tftp 200000 $(u-boot)\0"					\
 	"netmask=255.255.0.0\0"						\
 	"ipaddr=192.168.160.18\0"					\
 	"serverip=192.168.1.1\0"					\
 	"ethaddr=00:e0:ee:00:05:2e\0"					\
 	"bootfile=/tftpboot/v38b/uImage\0"				\
 	"u-boot=/tftpboot/v38b/u-boot.bin\0"				\
 	""

 #define CONFIG_BOOTCOMMAND	"run net_nfs"

 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK			/* define for 133MHz speed */

 /*
  * I2C configuration
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support */
 #define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */
 #define CONFIG_SYS_I2C_SPEED		100000	/* 100 kHz */
 #define CONFIG_SYS_I2C_SLAVE		0x7F

 /*
  * EEPROM configuration
  */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70

 /*
  * RTC configuration
  */
 #define CONFIG_SYS_I2C_RTC_ADDR		0x51

 /*
  * Flash configuration - use CFI driver
  */
 #define CONFIG_SYS_FLASH_CFI		1		/* Flash is CFI conformant */
 #define CONFIG_FLASH_CFI_DRIVER	1		/* Use the common driver */
 #define CONFIG_SYS_FLASH_CFI_AMD_RESET	1
 #define CONFIG_SYS_FLASH_BASE		0xFF000000
 #define CONFIG_SYS_MAX_FLASH_BANKS	1		/* max num of flash banks */
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 #define CONFIG_SYS_FLASH_SIZE		0x01000000	/* 16 MiB */
 #define CONFIG_SYS_MAX_FLASH_SECT	256		/* max num of sects on one chip */
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1	/* flash write speed-up */

 /*
  * Environment settings
  */
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00040000)
 #define CONFIG_ENV_SIZE		0x10000
 #define CONFIG_ENV_SECT_SIZE	0x10000
 #define CONFIG_ENV_OVERWRITE	1

 /*
  * Memory map
  */
 #define CONFIG_SYS_MBAR		0xF0000000
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_DEFAULT_MBAR	0x80000000

 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT		1
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256kB for Monitor */
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128kB for malloc() */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Linux initial memory map */

 /*
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC	1
 #define CONFIG_MPC5xxx_FEC_MII100
 #define CONFIG_PHY_ADDR		0x00
 #define CONFIG_MII		1

 /*
  * GPIO configuration
  */
 #define CONFIG_SYS_GPS_PORT_CONFIG	0x90001404

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM */

 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 /*
  * Various low-level settings
  */
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE

 #define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
 #define CONFIG_SYS_BOOTCS_CFG		0x00047801
 #define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE

 #define CONFIG_SYS_CS_BURST		0x00000000
 #define CONFIG_SYS_CS_DEADCYCLE	0x33333333

 #define CONFIG_SYS_RESET_ADDRESS	0xff000000

 /*
  * IDE/ATA (supports IDE harddisk)
  */
 #undef CONFIG_IDE_8xx_PCCARD		/* Don't use IDE with PC Card Adapter */
 #undef CONFIG_IDE_8xx_DIRECT		/* Direct IDE not supported */
 #undef CONFIG_IDE_LED			/* LED for ide not supported */

 #define CONFIG_IDE_RESET		/* reset for ide supported */
 #define CONFIG_IDE_PREINIT

 #define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus */
 #define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus */

 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

 #define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA

 #define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)	/* data I/O offset */

 #define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)	/* normal register accesses offset */

 #define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)	/* alternate registers offset */

 #define CONFIG_SYS_ATA_STRIDE		4		/* Interval between registers */

 /*
  * Status LED
  */
 #define  CONFIG_STATUS_LED		/* Status LED enabled */
 #define  CONFIG_BOARD_SPECIFIC_LED	/* version has board specific leds */

 #define CONFIG_SYS_LED_BASE	MPC5XXX_GPT7_ENABLE	/* Timer 7 GPIO */
 #ifndef __ASSEMBLY__
 typedef unsigned int led_id_t;

 #define __led_toggle(_msk) \
 	do { \
 		*((volatile long *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \
 	} while(0)

 #define __led_set(_msk, _st) \
 	do { \
 		if ((_st)) \
 			*((volatile long *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \
 		else \
 			*((volatile long *) (CONFIG_SYS_LED_BASE)) |= (_msk); \
 	} while(0)

 #define __led_init(_msk, st) \
 	do { \
 		*((volatile long *) (CONFIG_SYS_LED_BASE)) |= 0x34; \
 	} while(0)
 #endif /* __ASSEMBLY__ */

 #endif /* __CONFIG_H */
	/*
	* (C) Copyright 2003-2006 Wolfgang Denk, DENX Software Engineering,
	* wd@denx.de.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/
	#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
	#define CONFIG_V38B 1 /* ...on V38B board */

	#define CONFIG_SYS_TEXT_BASE 0xFF000000

	#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ...running at 33.000000MHz */

	#define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */
	#define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */

	#undef CONFIG_HW_WATCHDOG /* don't use watchdog */

	#define CONFIG_NETCONSOLE 1

	#define CONFIG_BOARD_EARLY_INIT_R 1 /* do board-specific init */
	#define CONFIG_BOARD_EARLY_INIT_F 1 /* do board-specific init */
	#define CONFIG_MISC_INIT_R

	#define CONFIG_SYS_XLB_PIPELINING 1 /* gives better performance */

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/*
	* Serial console configuration
	*/
	#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
	#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }

	/*
	* DDR
	*/
	#define SDRAM_DDR 1 /* is DDR */
	/* Settings for XLB = 132 MHz */
	#define SDRAM_MODE 0x018D0000
	#define SDRAM_EMODE 0x40090000
	#define SDRAM_CONTROL 0x704f0f00
	#define SDRAM_CONFIG1 0x73722930
	#define SDRAM_CONFIG2 0x47770000
	#define SDRAM_TAPDELAY 0x10000000

	/*
	* PCI - no suport
	*/
	#undef CONFIG_PCI

	/*
	* Partitions
	*/
	#define CONFIG_MAC_PARTITION 1
	#define CONFIG_DOS_PARTITION 1

	/*
	* USB
	*/
	#define CONFIG_USB_OHCI
	#define CONFIG_USB_STORAGE
	#define CONFIG_USB_CLOCK 0x0001BBBB
	#define CONFIG_USB_CONFIG 0x00001000


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IDE
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_DIAG
	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_JFFS2
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_SDRAM
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_USB
	#define CONFIG_CMD_FAT


	#define CONFIG_TIMESTAMP /* Print image info with timestamp */

	/*
	* Boot low with 16 MB Flash
	*/
	#define CONFIG_SYS_LOWBOOT 1
	#define CONFIG_SYS_LOWBOOT16 1

	/*
	* Autobooting
	*/
	#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */

	#define CONFIG_PREBOOT "echo;" \
	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
	"echo"

	#undef CONFIG_BOOTARGS

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"bootcmd=run net_nfs\0" \
	"bootdelay=3\0" \
	"baudrate=115200\0" \
	"preboot=echo;echo Type \"run flash_nfs\" to mount root " \
	"filesystem over NFS; echo\0" \
	"netdev=eth0\0" \
	"ramargs=setenv bootargs root=/dev/ram rw wdt=off \0" \
	"addip=setenv bootargs $(bootargs) " \
	"ip=$(ipaddr):$(serverip):$(gatewayip):" \
	"$(netmask):$(hostname):$(netdev):off panic=1\0" \
	"flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \
	"flash_self=run ramargs addip;bootm $(kernel_addr) " \
	"$(ramdisk_addr)\0" \
	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$(serverip):$(rootpath) wdt=off\0" \
	"hostname=v38b\0" \
	"ethact=FEC\0" \
	"rootpath=/opt/eldk-3.1.1/ppc_6xx\0" \
	"update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; " \
	"cp.b 200000 ff000000 $(filesize);" \
	"prot on ff000000 ff03ffff\0" \
	"load=tftp 200000 $(u-boot)\0" \
	"netmask=255.255.0.0\0" \
	"ipaddr=192.168.160.18\0" \
	"serverip=192.168.1.1\0" \
	"ethaddr=00:e0:ee:00:05:2e\0" \
	"bootfile=/tftpboot/v38b/uImage\0" \
	"u-boot=/tftpboot/v38b/u-boot.bin\0" \
	""

	#define CONFIG_BOOTCOMMAND "run net_nfs"

	/*
	* IPB Bus clocking configuration.
	*/
	#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */

	/*
	* I2C configuration
	*/
	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
	#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
	#define CONFIG_SYS_I2C_SLAVE 0x7F

	/*
	* EEPROM configuration
	*/
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70

	/*
	* RTC configuration
	*/
	#define CONFIG_SYS_I2C_RTC_ADDR 0x51

	/*
	* Flash configuration - use CFI driver
	*/
	#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
	#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
	#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1
	#define CONFIG_SYS_FLASH_BASE 0xFF000000
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	#define CONFIG_SYS_FLASH_SIZE 0x01000000 /* 16 MiB */
	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */

	/*
	* Environment settings
	*/
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
	#define CONFIG_ENV_SIZE 0x10000
	#define CONFIG_ENV_SECT_SIZE 0x10000
	#define CONFIG_ENV_OVERWRITE 1

	/*
	* Memory map
	*/
	#define CONFIG_SYS_MBAR 0xF0000000
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_DEFAULT_MBAR 0x80000000

	/* Use SRAM until RAM will be available */
	#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
	#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	# define CONFIG_SYS_RAMBOOT 1
	#endif

	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128kB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Linux initial memory map */

	/*
	* Ethernet configuration
	*/
	#define CONFIG_MPC5xxx_FEC 1
	#define CONFIG_MPC5xxx_FEC_MII100
	#define CONFIG_PHY_ADDR 0x00
	#define CONFIG_MII 1

	/*
	* GPIO configuration
	*/
	#define CONFIG_SYS_GPS_PORT_CONFIG 0x90001404

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	/*
	* Various low-level settings
	*/
	#define CONFIG_SYS_HID0_INIT HID0_ICE \| HID0_ICFI
	#define CONFIG_SYS_HID0_FINAL HID0_ICE

	#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
	#define CONFIG_SYS_BOOTCS_CFG 0x00047801
	#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE

	#define CONFIG_SYS_CS_BURST 0x00000000
	#define CONFIG_SYS_CS_DEADCYCLE 0x33333333

	#define CONFIG_SYS_RESET_ADDRESS 0xff000000

	/*
	* IDE/ATA (supports IDE harddisk)
	*/
	#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */
	#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
	#undef CONFIG_IDE_LED /* LED for ide not supported */

	#define CONFIG_IDE_RESET /* reset for ide supported */
	#define CONFIG_IDE_PREINIT

	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
	#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */

	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000

	#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA

	#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* data I/O offset */

	#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* normal register accesses offset */

	#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* alternate registers offset */

	#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */

	/*
	* Status LED
	*/
	#define CONFIG_STATUS_LED /* Status LED enabled */
	#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */

	#define CONFIG_SYS_LED_BASE MPC5XXX_GPT7_ENABLE /* Timer 7 GPIO */
	#ifndef __ASSEMBLY__
	typedef unsigned int led_id_t;

	#define __led_toggle(_msk) \
	do { \
	((volatile long ) (CONFIG_SYS_LED_BASE)) ^= (_msk); \
	} while(0)

	#define __led_set(_msk, _st) \
	do { \
	if ((_st)) \
	((volatile long ) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \
	else \
	((volatile long ) (CONFIG_SYS_LED_BASE)) \|= (_msk); \
	} while(0)

	#define __led_init(_msk, st) \
	do { \
	((volatile long ) (CONFIG_SYS_LED_BASE)) \|= 0x34; \
	} while(0)
	#endif /* __ASSEMBLY__ */

	#endif /* __CONFIG_H */