| /* |
| * Common board functions for Siemens TAURUS (AT91SAM9G20) based boards |
| * (C) Copyright 2013 Siemens AG |
| * |
| * Based on: |
| * U-Boot file: include/configs/at91sam9260ek.h |
| * |
| * (C) Copyright 2007-2008 |
| * Stelian Pop <stelian@popies.net> |
| * Lead Tech Design <www.leadtechdesign.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * SoC must be defined first, before hardware.h is included. |
| * In this case SoC is defined in boards.cfg. |
| */ |
| #include <asm/hardware.h> |
| |
| #define CONFIG_SYS_GENERIC_BOARD |
| |
| #if defined(CONFIG_SPL_BUILD) |
| #define CONFIG_SYS_THUMB_BUILD |
| #define CONFIG_SYS_ICACHE_OFF |
| #define CONFIG_SYS_DCACHE_OFF |
| #endif |
| /* |
| * Warning: changing CONFIG_SYS_TEXT_BASE requires |
| * adapting the initial boot program. |
| * Since the linker has to swallow that define, we must use a pure |
| * hex number here! |
| */ |
| |
| |
| #define CONFIG_SYS_TEXT_BASE 0x21000000 |
| |
| /* ARM asynchronous clock */ |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */ |
| |
| /* Misc CPU related */ |
| #define CONFIG_ARCH_CPU_INIT |
| #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_DISPLAY_CPUINFO |
| |
| #define CONFIG_CMD_BOOTZ |
| #define CONFIG_OF_LIBFDT |
| |
| /* general purpose I/O */ |
| #define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ |
| #define CONFIG_AT91_GPIO |
| #define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ |
| |
| /* serial console */ |
| #define CONFIG_ATMEL_USART |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID ATMEL_ID_SYS |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| #undef CONFIG_CMD_BDI |
| #undef CONFIG_CMD_FPGA |
| #undef CONFIG_CMD_IMI |
| #undef CONFIG_CMD_IMLS |
| #undef CONFIG_CMD_LOADS |
| #undef CONFIG_CMD_SOURCE |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_NAND |
| |
| /* |
| * SDRAM: 1 bank, min 32, max 128 MB |
| * Initialized before u-boot gets started. |
| */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 |
| #define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) |
| |
| /* |
| * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, |
| * leaving the correct space for initial global data structure above |
| * that address while providing maximum stack area below. |
| */ |
| # define CONFIG_SYS_INIT_SP_ADDR \ |
| (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) |
| |
| /* NAND flash */ |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_NAND_ATMEL |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 |
| #define CONFIG_SYS_NAND_DBW_8 |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) |
| #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 |
| #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 |
| #endif |
| |
| /* NOR flash - no real flash on this board */ |
| #define CONFIG_SYS_NO_FLASH 1 |
| |
| /* Ethernet */ |
| #define CONFIG_MACB |
| #define CONFIG_RMII |
| #define CONFIG_AT91_WANTS_COMMON_PHY |
| |
| #define CONFIG_AT91SAM9_WATCHDOG |
| #if !defined(CONFIG_SPL_BUILD) |
| /* Enable the watchdog */ |
| #define CONFIG_HW_WATCHDOG |
| #endif |
| |
| /* USB */ |
| #if defined(CONFIG_BOARD_TAURUS) |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 |
| #define CONFIG_USB_STORAGE |
| #endif |
| |
| /* SPI EEPROM */ |
| #define CONFIG_SPI |
| #define CONFIG_CMD_SPI |
| #define CONFIG_CMD_SF |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_ATMEL_SPI |
| #define CONFIG_SPI_FLASH_STMICRO |
| #define TAURUS_SPI_MASK (1 << 4) |
| #define TAURUS_SPI_CS_PIN AT91_PIN_PA3 |
| |
| #if defined(CONFIG_SPL_BUILD) |
| /* SPL related */ |
| #undef CONFIG_SPL_OS_BOOT /* Not supported by existing map */ |
| #define CONFIG_SPL_SPI_SUPPORT |
| #define CONFIG_SPL_SPI_FLASH_SUPPORT |
| #define CONFIG_SPL_SPI_LOAD |
| #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 |
| |
| #define CONFIG_SF_DEFAULT_BUS 0 |
| #define CONFIG_SF_DEFAULT_SPEED 10000000 |
| #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 |
| #endif |
| |
| /* load address */ |
| #define CONFIG_SYS_LOAD_ADDR 0x22000000 |
| |
| /* bootstrap in spi flash , u-boot + env + linux in nandflash */ |
| #define CONFIG_ENV_IS_IN_NAND |
| #define CONFIG_ENV_OFFSET 0x100000 |
| #define CONFIG_ENV_OFFSET_REDUND 0x180000 |
| #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ |
| #define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm" |
| #define CONFIG_BOOTARGS \ |
| "console=ttyS0,115200 earlyprintk " \ |
| "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ |
| "256k(env),256k(env_redundant),256k(spare)," \ |
| "512k(dtb),6M(kernel)ro,-(rootfs) " \ |
| "root=/dev/mtdblock7 rw rootfstype=jffs2" |
| |
| #define CONFIG_SYS_PROMPT "U-Boot> " |
| #define CONFIG_SYS_CBSIZE 256 |
| #define CONFIG_SYS_MAXARGS 16 |
| #define CONFIG_SYS_PBSIZE \ |
| (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_LONGHELP |
| #define CONFIG_CMDLINE_EDITING |
| #define CONFIG_AUTO_COMPLETE |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN \ |
| ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) |
| |
| /* Defines for SPL */ |
| #define CONFIG_SPL_FRAMEWORK |
| #define CONFIG_SPL_TEXT_BASE 0x0 |
| #define CONFIG_SPL_MAX_SIZE (14 * 1024) |
| #define CONFIG_SPL_STACK (16 * 1024) |
| #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ |
| CONFIG_SYS_MALLOC_LEN) |
| #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN |
| |
| #define CONFIG_SPL_BSS_START_ADDR CONFIG_SPL_MAX_SIZE |
| #define CONFIG_SPL_BSS_MAX_SIZE (3 * 1024) |
| |
| #define CONFIG_SPL_LIBCOMMON_SUPPORT |
| #define CONFIG_SPL_LIBGENERIC_SUPPORT |
| #define CONFIG_SPL_SERIAL_SUPPORT |
| |
| #define CONFIG_SPL_BOARD_INIT |
| #define CONFIG_SPL_GPIO_SUPPORT |
| #define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14) |
| #define CONFIG_SPL_NAND_SUPPORT |
| #define CONFIG_SYS_USE_NANDFLASH 1 |
| #define CONFIG_SPL_NAND_DRIVERS |
| #define CONFIG_SPL_NAND_BASE |
| #define CONFIG_SPL_NAND_ECC |
| #define CONFIG_SPL_NAND_RAW_ONLY |
| #define CONFIG_SPL_NAND_SOFTECC |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x20000 |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000 |
| #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_NAND_5_ADDR_CYCLE |
| |
| #define CONFIG_SYS_NAND_SIZE (256*1024*1024) |
| #define CONFIG_SYS_NAND_PAGE_SIZE 2048 |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) |
| #define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ |
| CONFIG_SYS_NAND_PAGE_SIZE) |
| #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS |
| #define CONFIG_SYS_NAND_ECCSIZE 256 |
| #define CONFIG_SYS_NAND_ECCBYTES 3 |
| #define CONFIG_SYS_NAND_OOBSIZE 64 |
| #define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \ |
| 48, 49, 50, 51, 52, 53, 54, 55, \ |
| 56, 57, 58, 59, 60, 61, 62, 63, } |
| |
| |
| #define CONFIG_SPL_ATMEL_SIZE |
| #define CONFIG_SYS_MASTER_CLOCK 132096000 |
| #define AT91_PLL_LOCK_TIMEOUT 1000000 |
| #define CONFIG_SYS_AT91_PLLA 0x202A3F01 |
| #define CONFIG_SYS_MCKR 0x1300 |
| #define CONFIG_SYS_MCKR_CSS (0x02 | CONFIG_SYS_MCKR) |
| #define CONFIG_SYS_AT91_PLLB 0x10193F05 |
| #endif |