| /* |
| * (C) Copyright 2003 |
| * Texas Instruments. |
| * Kshitij Gupta <kshitij@ti.com> |
| * Configuation settings for the TI OMAP Innovator board. |
| * |
| * (C) Copyright 2004 |
| * ARM Ltd. |
| * Philippe Robin, <philippe.robin@arm.com> |
| * Configuration for Compact Integrator board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include "integrator-common.h" |
| |
| /* Integrator CP-specific configuration */ |
| #define CONFIG_ARCH_CINTEGRATOR |
| #define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer 1 is clocked at 1Mhz */ |
| |
| /* |
| * Hardware drivers |
| */ |
| #define CONFIG_SMC91111 |
| #define CONFIG_SMC_USE_32_BIT |
| #define CONFIG_SMC91111_BASE 0xC8000000 |
| #undef CONFIG_SMC91111_EXT_PHY |
| |
| /* PL011 configuration */ |
| #define CONFIG_PL011_SERIAL |
| #define CONFIG_PL011_CLOCK 14745600 |
| #define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, (void *)CONFIG_SYS_SERIAL1 } |
| #define CONFIG_CONS_INDEX 0 |
| #define CONFIG_BAUDRATE 38400 |
| #define CONFIG_SYS_SERIAL0 0x16000000 |
| #define CONFIG_SYS_SERIAL1 0x17000000 |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_BOOTDELAY 2 |
| #define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyAMA0 console=tty ip=dhcp netdev=27,0,0xfc800000,0xfc800010,eth0 video=clcdfb:0" |
| #define CONFIG_BOOTCOMMAND "tftpboot ; bootm" |
| #define CONFIG_SERVERIP 192.168.1.100 |
| #define CONFIG_IPADDR 192.168.1.104 |
| #define CONFIG_BOOTFILE "uImage" |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_PROMPT "Integrator-CP # " /* Monitor Command Prompt */ |
| |
| #define PHYS_FLASH_SIZE 0x01000000 /* 16MB */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_SYS_MONITOR_LEN 0x00100000 |
| |
| /* |
| * Move up the U-Boot & monitor area if more flash is fitted. |
| * If this U-Boot is to be run on Integrators with varying flash sizes, |
| * drivers/mtd/cfi_flash.c::flash_init() can read the Integrator CP_FLASHPROG |
| * register and dynamically assign CONFIG_ENV_ADDR & CONFIG_SYS_MONITOR_BASE |
| * - CONFIG_SYS_MONITOR_BASE is set to indicate that the environment is not |
| * embedded in the boot monitor(s) area |
| */ |
| #if ( PHYS_FLASH_SIZE == 0x04000000 ) |
| |
| #define CONFIG_ENV_ADDR 0x27F00000 |
| #define CONFIG_SYS_MONITOR_BASE 0x27F40000 |
| |
| #elif (PHYS_FLASH_SIZE == 0x02000000 ) |
| |
| #define CONFIG_ENV_ADDR 0x25F00000 |
| #define CONFIG_SYS_MONITOR_BASE 0x25F40000 |
| |
| #else |
| |
| #define CONFIG_ENV_ADDR 0x24F00000 |
| #define CONFIG_SYS_MONITOR_BASE 0x27F40000 |
| |
| #endif |
| |
| #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */ |
| #define CONFIG_ENV_SIZE 8192 /* 8KB */ |
| |
| #endif /* __CONFIG_H */ |