blob: 19ca66e3d035a9122ac03c9e34e9cf62e26d9181 [file] [log] [blame]
/*
* Copyright 2012 Freescale Semiconductor, Inc.
* Author: Sandeep Kumar Singh <sandeep@freescale.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* This file is based on board/freescale/corenet_ds/eth_superhydra.c */
/*
* This file handles the board muxing between the Fman Ethernet MACs and
* the RGMII/SGMII/XGMII PHYs on a Freescale B4860 "Centaur". The SGMII
* PHYs are the two on-board 1Gb ports. There are no RGMII PHY on board.
* The 10Gb XGMII PHY is provided via the XAUI riser card. There is only
* one Fman device on B4860. The SERDES configuration is used to determine
* where the SGMII and XAUI cards exist, and also which Fman MACs are routed
* to which PHYs. So for a given Fman MAC, there is one and only PHY it
* connects to. MACs cannot be routed to PHYs dynamically. This configuration
* is done at boot time by reading SERDES protocol from RCW.
*/
#include <common.h>
#include <netdev.h>
#include <asm/fsl_serdes.h>
#include <fm_eth.h>
#include <fsl_mdio.h>
#include <malloc.h>
#include <fdt_support.h>
#include <asm/fsl_dtsec.h>
#include "../common/ngpixis.h"
#include "../common/fman.h"
#include "../common/qixis.h"
#include "b4860qds_qixis.h"
#define EMI_NONE 0xFFFFFFFF
#ifdef CONFIG_FMAN_ENET
/*
* Mapping of all 16 SERDES lanes to board slots. A value n(>0) will mean that
* lane at index is mapped to slot number n. A value of '0' will mean
* that the mapping must be determined dynamically, or that the lane maps to
* something other than a board slot
*/
static u8 lane_to_slot[] = {
0, 0, 0, 0,
0, 0, 0, 0,
1, 1, 1, 1,
0, 0, 0, 0
};
/*
* This function initializes the lane_to_slot[] array. It reads RCW to check
* if Serdes2{E,F,G,H} is configured as slot 2 or as SFP and initializes
* lane_to_slot[] accordingly
*/
static void initialize_lane_to_slot(void)
{
unsigned int serdes2_prtcl;
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
debug("Initializing lane to slot: Serdes2 protocol: %x\n",
serdes2_prtcl);
switch (serdes2_prtcl) {
case 0x18:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: SGMII
* Lanes: E,F: Aur
* Lanes: G,H: SRIO
*/
case 0x91:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B: SGMII
* Lanes: C,D: SRIO2
* Lanes: E,F,G,H: XAUI2
*/
case 0x93:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: SGMII
* Lanes: E,F,G,H: XAUI2
*/
case 0x98:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: XAUI2
* Lanes: E,F,G,H: XAUI2
*/
case 0x9a:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B: PCI
* Lanes: C,D: SGMII
* Lanes: E,F,G,H: XAUI2
*/
case 0x9e:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: PCI
* Lanes: E,F,G,H: XAUI2
*/
case 0xb2:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B,C,D: PCI
* Lanes: E,F: SGMII 3&4
* Lanes: G,H: XFI
*/
case 0xc2:
/*
* Configuration:
* SERDES: 2
* Lanes: A,B: SGMII
* Lanes: C,D: SRIO2
* Lanes: E,F,G,H: XAUI2
*/
lane_to_slot[12] = 2;
lane_to_slot[13] = lane_to_slot[12];
lane_to_slot[14] = lane_to_slot[12];
lane_to_slot[15] = lane_to_slot[12];
break;
default:
printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n",
serdes2_prtcl);
break;
}
return;
}
#endif /* #ifdef CONFIG_FMAN_ENET */
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_FMAN_ENET
struct memac_mdio_info memac_mdio_info;
struct memac_mdio_info tg_memac_mdio_info;
unsigned int i;
unsigned int serdes1_prtcl, serdes2_prtcl;
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
if (!serdes1_prtcl) {
printf("SERDES1 is not enabled\n");
return 0;
}
serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl);
serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
if (!serdes2_prtcl) {
printf("SERDES2 is not enabled\n");
return 0;
}
serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl);
printf("Initializing Fman\n");
initialize_lane_to_slot();
memac_mdio_info.regs =
(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
memac_mdio_info.name = DEFAULT_FM_MDIO_NAME;
/* Register the real 1G MDIO bus */
fm_memac_mdio_init(bis, &memac_mdio_info);
tg_memac_mdio_info.regs =
(struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
tg_memac_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
/* Register the real 10G MDIO bus */
fm_memac_mdio_init(bis, &tg_memac_mdio_info);
/*
* Program the two on board DTSEC PHY addresses assuming that they are
* all SGMII. RGMII is not supported on this board. Setting SGMII 5 and
* 6 to on board SGMII phys
*/
fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
switch (serdes1_prtcl) {
case 0x2a:
/* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */
debug("Setting phy addresses for FM1_DTSEC5: %x and"
"FM1_DTSEC6: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
/* Fixing Serdes clock by programming FPGA register */
QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
fm_info_set_phy_address(FM1_DTSEC5,
CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC6,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
break;
#ifdef CONFIG_PPC_B4420
case 0x18:
/* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */
debug("Setting phy addresses for FM1_DTSEC3: %x and"
"FM1_DTSEC4: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
/* Fixing Serdes clock by programming FPGA register */
QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
break;
#endif
default:
printf("Fman: Unsupported SerDes1 Protocol 0x%02x\n",
serdes1_prtcl);
break;
}
switch (serdes2_prtcl) {
case 0x18:
debug("Setting phy addresses on SGMII Riser card for"
"FM1_DTSEC ports: \n");
fm_info_set_phy_address(FM1_DTSEC1,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2,
CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR);
break;
case 0x49:
debug("Setting phy addresses on SGMII Riser card for"
"FM1_DTSEC ports: \n");
fm_info_set_phy_address(FM1_DTSEC1,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2,
CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR);
break;
case 0x8d:
case 0xb2:
debug("Setting phy addresses on SGMII Riser card for"
"FM1_DTSEC ports: \n");
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
break;
case 0x98:
/* XAUI in Slot1 and Slot2 */
debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC1: %x\n",
CONFIG_SYS_FM1_10GEC1_PHY_ADDR);
fm_info_set_phy_address(FM1_10GEC1,
CONFIG_SYS_FM1_10GEC1_PHY_ADDR);
debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC2: %x\n",
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
fm_info_set_phy_address(FM1_10GEC2,
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
break;
case 0x9E:
/* XAUI in Slot2 */
debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC2: %x\n",
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
fm_info_set_phy_address(FM1_10GEC2,
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
break;
default:
printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n",
serdes2_prtcl);
break;
}
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
int idx = i - FM1_DTSEC1;
switch (fm_info_get_enet_if(i)) {
case PHY_INTERFACE_MODE_SGMII:
fm_info_set_mdio(i,
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
break;
case PHY_INTERFACE_MODE_NONE:
fm_info_set_phy_address(i, 0);
break;
default:
printf("Fman1: DTSEC%u set to unknown interface %i\n",
idx + 1, fm_info_get_enet_if(i));
fm_info_set_phy_address(i, 0);
break;
}
}
for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
int idx = i - FM1_10GEC1;
switch (fm_info_get_enet_if(i)) {
case PHY_INTERFACE_MODE_XGMII:
fm_info_set_mdio(i,
miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME));
break;
default:
printf("Fman1: 10GSEC%u set to unknown interface %i\n",
idx + 1, fm_info_get_enet_if(i));
fm_info_set_phy_address(i, 0);
break;
}
}
cpu_eth_init(bis);
#endif
return pci_eth_init(bis);
}
void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
enum fm_port port, int offset)
{
int phy;
char alias[32];
if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
phy = fm_info_get_phy_address(port);
sprintf(alias, "phy_sgmii_%x", phy);
fdt_set_phy_handle(fdt, compat, addr, alias);
}
}
void fdt_fixup_board_enet(void *fdt)
{
int i;
char alias[32];
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
switch (fm_info_get_enet_if(i)) {
case PHY_INTERFACE_MODE_NONE:
sprintf(alias, "ethernet%u", i);
fdt_status_disabled_by_alias(fdt, alias);
break;
default:
break;
}
}
}