blob: ff385d9c6bef54b897eba244801b7e42de99ffb1 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
* Copyright (C) 2016 Mario Six <mario.six@gdsys.cc>
*/
#ifndef _CONFIG_CONTROLCENTERDC_H
#define _CONFIG_CONTROLCENTERDC_H
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_CUSTOMER_BOARD_SUPPORT
/*
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
* for DDR ECC byte filling in the SPL before loading the main
* U-Boot into it.
*/
/*
* SATA/SCSI/AHCI configuration
*/
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
/* Environment in SPI NOR flash */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI_SCAN_SHOW
#endif
/*
* Software (bit-bang) MII driver configuration
*/
#define CONFIG_BITBANGMII_MULTI
/* SPL */
/*
* Select the boot device here
*
* Currently supported are:
* SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
* SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1)
*/
#define SPL_BOOT_SPI_NOR_FLASH 1
#define SPL_BOOT_SDIO_MMC_CARD 2
#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH
/* Defines for SPL */
#define CONFIG_SPL_SIZE (160 << 10)
#if defined(CONFIG_SECURED_MODE_IMAGE)
#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x2614)
#else
#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x30)
#endif
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
#define CONFIG_SPL_STACK (0x40000000 + ((212 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
/* SPL related MMC defines */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
#endif
#endif
/*
* Environment Configuration
*/
#define CONFIG_HOSTNAME "ccdc"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "ccdc.img"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth1\0" \
"consoledev=ttyS1\0" \
"u-boot=u-boot.bin\0" \
"bootfile_addr=1000000\0" \
"keyprogram_addr=3000000\0" \
"keyprogram_file=keyprogram.img\0" \
"fdtfile=controlcenterdc.dtb\0" \
"load=tftpboot ${loadaddr} ${u-boot}\0" \
"mmcdev=0:2\0" \
"update=sf probe 1:0;" \
" sf erase 0 +${filesize};" \
" sf write ${fileaddr} 0 ${filesize}\0" \
"upd=run load update\0" \
"fdt_high=0x10000000\0" \
"initrd_high=0x10000000\0" \
"loadkeyprogram=tpm flush_keys;" \
" mmc rescan;" \
" ext4load mmc ${mmcdev} ${keyprogram_addr} ${keyprogram_file};"\
" source ${keyprogram_addr}:script@1\0" \
"gpio1=gpio@22_25\0" \
"gpio2=A29\0" \
"blinkseq='0 0 0 0 2 0 2 2 3 1 3 1 0 0 2 2 3 1 3 3 2 0 2 2 3 1 1 1 " \
"2 0 2 2 3 1 3 1 0 0 2 0 3 3 3 1 2 0 0 0 3 1 1 1 0 0 0 0'\0" \
"bootfail=for i in ${blinkseq}; do" \
" if test $i -eq 0; then" \
" gpio clear ${gpio1}; gpio set ${gpio2};" \
" elif test $i -eq 1; then" \
" gpio clear ${gpio1}; gpio clear ${gpio2};" \
" elif test $i -eq 2; then" \
" gpio set ${gpio1}; gpio set ${gpio2};" \
" else;" \
" gpio clear ${gpio1}; gpio set ${gpio2};" \
" fi; sleep 0.12; done\0"
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
#endif /* _CONFIG_CONTROLCENTERDC_H */