| /* |
| * (C) Copyright 2010 |
| * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_405EP 1 /* this is a PPC405 CPU */ |
| #define CONFIG_DLVISION_10G 1 /* on a DLVision-10G board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 |
| |
| /* |
| * Include common defines/options for all AMCC eval boards |
| */ |
| #define CONFIG_HOSTNAME dlvsion-10g |
| #define CONFIG_IDENT_STRING " dlvision-10g 0.06" |
| #include "amcc-common.h" |
| |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_BOARD_EARLY_INIT_R |
| #define CONFIG_MISC_INIT_R |
| #define CONFIG_LAST_STAGE_INIT |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| |
| #undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */ |
| |
| /* |
| * Configure PLL |
| */ |
| #define PLLMR0_DEFAULT PLLMR0_266_133_66 |
| #define PLLMR1_DEFAULT PLLMR1_266_133_66 |
| |
| /* new uImage format support */ |
| #define CONFIG_FIT |
| #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ |
| #define CONFIG_FIT_DISABLE_SHA256 |
| |
| #define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */ |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_AMCC_DEF_ENV \ |
| CONFIG_AMCC_DEF_ENV_POWERPC \ |
| CONFIG_AMCC_DEF_ENV_NOR_UPD \ |
| "kernel_addr=fc000000\0" \ |
| "fdt_addr=fc1e0000\0" \ |
| "ramdisk_addr=fc200000\0" \ |
| "" |
| |
| #define CONFIG_PHY_ADDR 4 /* PHY address */ |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_PHY1_ADDR 0xc /* EMAC1 PHY address */ |
| #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ |
| |
| /* |
| * Commands additional to the ones defined in amcc-common.h |
| */ |
| #define CONFIG_CMD_DTT |
| #undef CONFIG_CMD_DHCP |
| #undef CONFIG_CMD_DIAG |
| #undef CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| #undef CONFIG_CMD_IRQ |
| |
| /* |
| * SDRAM configuration (please see cpu/ppc/sdram.[ch]) |
| */ |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ |
| |
| /* SDRAM timings used in datasheet */ |
| #define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */ |
| #define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */ |
| #define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE period */ |
| #define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ |
| #define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */ |
| |
| /* |
| * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. |
| * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. |
| * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD. |
| * The Linux BASE_BAUD define should match this configuration. |
| * baseBaud = cpuClock/(uartDivisor*16) |
| * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, |
| * set Linux BASE_BAUD to 403200. |
| */ |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ |
| #undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| /* |
| * I2C stuff |
| */ |
| #define CONFIG_SYS_I2C_PPC4XX |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F |
| |
| #define CONFIG_SYS_I2C_IHS |
| #define CONFIG_SYS_I2C_IHS_DUAL |
| #define CONFIG_SYS_I2C_IHS_CH0 |
| #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F |
| #define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F |
| #define CONFIG_SYS_I2C_IHS_CH1 |
| #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F |
| #define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000 |
| #define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F |
| |
| #define CONFIG_SYS_SPD_BUS_NUM 4 |
| |
| /* Temp sensor/hwmon/dtt */ |
| #define CONFIG_SYS_DTT_BUS_NUM 4 |
| #define CONFIG_DTT_LM63 1 /* National LM63 */ |
| #define CONFIG_DTT_SENSORS { 0x4c, 0x4e, 0x18 } /* Sensor addresses */ |
| #define CONFIG_DTT_PWM_LOOKUPTABLE \ |
| { { 46, 10 }, { 48, 14 }, { 50, 19 }, { 52, 23 },\ |
| { 54, 27 }, { 56, 31 }, { 58, 36 }, { 60, 40 } } |
| #define CONFIG_DTT_TACH_LIMIT 0xa10 |
| |
| #define CONFIG_SYS_ICS8N3QV01_I2C {1, 3} |
| #define CONFIG_SYS_SIL1178_I2C {0, 2} |
| #define CONFIG_SYS_DP501_I2C {0, 2} |
| |
| /* EBC peripherals */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xFC000000 |
| #define CONFIG_SYS_FPGA0_BASE 0x7f100000 |
| #define CONFIG_SYS_FPGA1_BASE 0x7f200000 |
| #define CONFIG_SYS_LATCH_BASE 0x7f300000 |
| |
| #define CONFIG_SYS_FPGA_BASE(k) \ |
| (k ? CONFIG_SYS_FPGA1_BASE : CONFIG_SYS_FPGA0_BASE) |
| |
| #define CONFIG_SYS_FPGA_DONE(k) \ |
| (k ? 0x2000 : 0x1000) |
| |
| #define CONFIG_SYS_FPGA_COUNT 2 |
| |
| #define CONFIG_SYS_FPGA_PTR { \ |
| (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, \ |
| (struct ihs_fpga *)CONFIG_SYS_FPGA1_BASE } |
| |
| #define CONFIG_SYS_FPGA_COMMON |
| |
| #define CONFIG_SYS_LATCH0_RESET 0xffff |
| #define CONFIG_SYS_LATCH0_BOOT 0xffff |
| #define CONFIG_SYS_LATCH1_RESET 0xffbf |
| #define CONFIG_SYS_LATCH1_BOOT 0xffff |
| |
| #define CONFIG_SYS_FPGA_NO_RFL_HI |
| |
| /* |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors per chip*/ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms */ |
| |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buff'd writes */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */ |
| #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* no warn upon unknown flash */ |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ |
| #define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif |
| |
| /* |
| * PPC405 GPIO Configuration |
| */ |
| #define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \ |
| { \ |
| /* GPIO Core 0 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO5 TS3 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO6 TS4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO7 TS5 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO9 TrcClk */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \ |
| } \ |
| } |
| |
| /* |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory (OCM) for temperary stack until sdram is tested */ |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* in SDRAM */ |
| #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* Memory Bank 0 (NOR-flash) */ |
| #define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_ENABLED | \ |
| EBC_BXAP_FWT_ENCODE(8) | \ |
| EBC_BXAP_BWT_ENCODE(7) | \ |
| EBC_BXAP_BCE_DISABLE | \ |
| EBC_BXAP_BCT_2TRANS | \ |
| EBC_BXAP_CSN_ENCODE(0) | \ |
| EBC_BXAP_OEN_ENCODE(2) | \ |
| EBC_BXAP_WBN_ENCODE(2) | \ |
| EBC_BXAP_WBF_ENCODE(2) | \ |
| EBC_BXAP_TH_ENCODE(4) | \ |
| EBC_BXAP_RE_DISABLED | \ |
| EBC_BXAP_SOR_NONDELAYED | \ |
| EBC_BXAP_BEM_WRITEONLY | \ |
| EBC_BXAP_PEN_DISABLED) |
| #define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \ |
| EBC_BXCR_BS_64MB | \ |
| EBC_BXCR_BU_RW | \ |
| EBC_BXCR_BW_16BIT) |
| |
| /* Memory Bank 1 (FPGA0) */ |
| #define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \ |
| EBC_BXAP_TWT_ENCODE(5) | \ |
| EBC_BXAP_BCE_DISABLE | \ |
| EBC_BXAP_BCT_2TRANS | \ |
| EBC_BXAP_CSN_ENCODE(0) | \ |
| EBC_BXAP_OEN_ENCODE(2) | \ |
| EBC_BXAP_WBN_ENCODE(1) | \ |
| EBC_BXAP_WBF_ENCODE(1) | \ |
| EBC_BXAP_TH_ENCODE(0) | \ |
| EBC_BXAP_RE_DISABLED | \ |
| EBC_BXAP_SOR_NONDELAYED | \ |
| EBC_BXAP_BEM_WRITEONLY | \ |
| EBC_BXAP_PEN_DISABLED) |
| #define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA0_BASE) | \ |
| EBC_BXCR_BS_1MB | \ |
| EBC_BXCR_BU_RW | \ |
| EBC_BXCR_BW_16BIT) |
| |
| /* Memory Bank 2 (FPGA1) */ |
| #define CONFIG_SYS_EBC_PB2AP (EBC_BXAP_BME_DISABLED | \ |
| EBC_BXAP_TWT_ENCODE(6) | \ |
| EBC_BXAP_BCE_DISABLE | \ |
| EBC_BXAP_BCT_2TRANS | \ |
| EBC_BXAP_CSN_ENCODE(0) | \ |
| EBC_BXAP_OEN_ENCODE(2) | \ |
| EBC_BXAP_WBN_ENCODE(1) | \ |
| EBC_BXAP_WBF_ENCODE(1) | \ |
| EBC_BXAP_TH_ENCODE(0) | \ |
| EBC_BXAP_RE_DISABLED | \ |
| EBC_BXAP_SOR_NONDELAYED | \ |
| EBC_BXAP_BEM_WRITEONLY | \ |
| EBC_BXAP_PEN_DISABLED) |
| #define CONFIG_SYS_EBC_PB2CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA1_BASE) | \ |
| EBC_BXCR_BS_1MB | \ |
| EBC_BXCR_BU_RW | \ |
| EBC_BXCR_BW_16BIT) |
| |
| /* Memory Bank 3 (Latches) */ |
| #define CONFIG_SYS_EBC_PB3AP (EBC_BXAP_BME_ENABLED | \ |
| EBC_BXAP_FWT_ENCODE(8) | \ |
| EBC_BXAP_BWT_ENCODE(4) | \ |
| EBC_BXAP_BCE_DISABLE | \ |
| EBC_BXAP_BCT_2TRANS | \ |
| EBC_BXAP_CSN_ENCODE(0) | \ |
| EBC_BXAP_OEN_ENCODE(1) | \ |
| EBC_BXAP_WBN_ENCODE(1) | \ |
| EBC_BXAP_WBF_ENCODE(1) | \ |
| EBC_BXAP_TH_ENCODE(2) | \ |
| EBC_BXAP_RE_DISABLED | \ |
| EBC_BXAP_SOR_NONDELAYED | \ |
| EBC_BXAP_BEM_WRITEONLY | \ |
| EBC_BXAP_PEN_DISABLED) |
| #define CONFIG_SYS_EBC_PB3CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_LATCH_BASE) | \ |
| EBC_BXCR_BS_1MB | \ |
| EBC_BXCR_BU_RW | \ |
| EBC_BXCR_BW_16BIT) |
| |
| /* |
| * OSD Setup |
| */ |
| #define CONFIG_SYS_MPC92469AC |
| #define CONFIG_SYS_OSD_SCREENS CONFIG_SYS_FPGA_COUNT |
| #define CONFIG_SYS_DP501_DIFFERENTIAL |
| #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ |
| |
| #endif /* __CONFIG_H */ |