include/configs/hcu4.h - github/trini/u-boot - Gitiles

 /*
  *(C) Copyright 2005-2008 Netstal Maschinen AG
  *    Niklaus Giger (Niklaus.Giger@netstal.com)
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /************************************************************************
  * hcu4.h - configuration for HCU4 board (similar to hcu5.h)
  ***********************************************************************/

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*-----------------------------------------------------------------------
  * High Level Configuration Options
  *----------------------------------------------------------------------*/
 #define CONFIG_HCU4		1		/* Board is HCU4	*/
 #define CONFIG_4xx		1		/* ... PPC4xx family	*/
 #define CONFIG_405GP 1
 #define CONFIG_4xx   1
 #define CONFIG_HOSTNAME		hcu4

 #define	CONFIG_SYS_TEXT_BASE	0xFFFB0000

 /*
  * Include common defines/options for all boards produced by Netstal Maschinen
  */
 #include "netstal-common.h"

 #define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/

 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
 #define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/

 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
 *----------------------------------------------------------------------*/
 #define CONFIG_SYS_MONITOR_LEN	(320 * 1024)	/* Reserve 320 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(256 * 1024) /* Reserve 256 kB for malloc() */


 #define CONFIG_SYS_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CONFIG_SYS_FLASH_BASE		0xfff80000	/* start of FLASH	*/
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE

 /* ... with on-chip memory here (4KBytes) */
 #define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
 #define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
 /* Do not set up locked dcache as init ram. */
 #undef CONFIG_SYS_INIT_DCACHE_CS

 /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
 #define CONFIG_SYS_TEMP_STACK_OCM 1

 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR	/* OCM		*/
 #define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE
 #define CONFIG_SYS_GBL_DATA_SIZE	256		/* num bytes initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 0x4)

 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 /*
  * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
  * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
  * The Linux BASE_BAUD define should match this configuration.
  *    baseBaud = cpuClock/(uartDivisor*16)
  * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
  * set Linux BASE_BAUD to 403200.
  */
 #undef	CONFIG_SYS_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
 #define CONFIG_SYS_BASE_BAUD	    691200

 /* Set console baudrate to 9600 */
 #define CONFIG_BAUDRATE		9600

 /*-----------------------------------------------------------------------
  * Flash
  *----------------------------------------------------------------------*/

 /* Use common CFI driver */
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER
 /* board provides its own flash_init code */
 #define CONFIG_FLASH_CFI_LEGACY		1
 #define CONFIG_SYS_FLASH_CFI_WIDTH		FLASH_CFI_8BIT
 #define CONFIG_SYS_FLASH_LEGACY_512Kx8 1

 /* print 'E' for empty sector on flinfo */
 #define CONFIG_SYS_FLASH_EMPTY_INFO

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip */

 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/

 #undef	CONFIG_ENV_IS_IN_NVRAM
 #define CONFIG_ENV_IS_IN_FLASH
 #undef  CONFIG_ENV_IS_NOWHERE

 #ifdef  CONFIG_ENV_IS_IN_EEPROM
 /* Put the environment after the SDRAM configuration */
 #define PROM_SIZE	2048
 #define CONFIG_ENV_OFFSET	 512
 #define CONFIG_ENV_SIZE	(PROM_SIZE-CONFIG_ENV_OFFSET)
 #endif

 #ifdef CONFIG_ENV_IS_IN_FLASH
 /* Put the environment in Flash */
 #define CONFIG_ENV_SECT_SIZE	0x10000	/* size of one complete sector	*/
 #define CONFIG_ENV_ADDR		((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
 #define	CONFIG_ENV_SIZE		8*1024	/* 8 KB Environment Sector	*/

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 #endif

 /*-----------------------------------------------------------------------
  * I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
  * the first internal I2C controller of the PPC440EPx
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_SPD_BUS_NUM		0

 #define CONFIG_IPADDR		172.25.1.14

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	CONFIG_NETSTAL_DEF_ENV						\
 	CONFIG_NETSTAL_DEF_ENV_POWERPC					\
 	""

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_FLASH
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM

 /* SPD EEPROM (sdram speed config) disabled */
 #define CONFIG_SPD_EEPROM          1
 #define SPD_EEPROM_ADDRESS      0x50

 /* POST support */
 #define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
 				 CONFIG_SYS_POST_CPU	   | \
 				 CONFIG_SYS_POST_UART	   | \
 				 CONFIG_SYS_POST_I2C	   | \
 				 CONFIG_SYS_POST_CACHE	   | \
 				 CONFIG_SYS_POST_ETHER	   | \
 				 CONFIG_SYS_POST_SPR)

 #define CONFIG_SYS_POST_UART_TABLE	{ CONFIG_SYS_NS16550_COM1 }
 #undef  CONFIG_LOGBUFFER
 #define CONFIG_SYS_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */

 /*-----------------------------------------------------------------------
  * Miscellaneous configurable options
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 	#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 	#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/


 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  */

 #define CONFIG_SYS_EBC_CFG	0x98400000

 /* Memory Bank 0 (Flash Bank 0) initialization	*/
 #define CONFIG_SYS_EBC_PB0AP	0x02005400
 #define CONFIG_SYS_EBC_PB0CR	0xFFF18000  /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */

 #define CONFIG_SYS_EBC_PB1AP	0x03041200
 #define CONFIG_SYS_EBC_PB1CR	0x7009A000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/

 #define CONFIG_SYS_EBC_PB2AP	0x02054500
 #define CONFIG_SYS_EBC_PB2CR	0x78018000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/

 #define CONFIG_SYS_EBC_PB3AP	0x01840300
 #define CONFIG_SYS_EBC_PB3CR	0x7c0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/

 #define CONFIG_SYS_EBC_PB4AP	0x01800300
 #define CONFIG_SYS_EBC_PB4CR	0x7e0ba000  /* BAS=,BS=MB,BU=R/W,BW=bit	*/

 #define CONFIG_SYS_GPIO0_OR	0xF27FFFFF  /* GPIO value */
 #define CONFIG_SYS_GPIO0_TCR	0x7FFE0000  /* GPIO value */
 #define CONFIG_SYS_GPIO0_ODR	0x00E897FC  /* GPIO value */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)/* Initial Memory map for Linux */

 /* Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */

 #define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
 #define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/


 /* Configuration Port location */
 #define CONFIG_PORT_ADDR	0xF0000500

 #define CONFIG_SYS_HUSH_PARSER                 /* use "hush" command parser    */
 #ifdef  CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #endif

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	    /* which serial port to use */
 #endif

 #endif	/* __CONFIG_H */
	/*
	*(C) Copyright 2005-2008 Netstal Maschinen AG
	* Niklaus Giger (Niklaus.Giger@netstal.com)
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/************************************************************************
	* hcu4.h - configuration for HCU4 board (similar to hcu5.h)
	***********************************************************************/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*-----------------------------------------------------------------------
	* High Level Configuration Options
	----------------------------------------------------------------------/
	#define CONFIG_HCU4 1 /* Board is HCU4 */
	#define CONFIG_4xx 1 /* ... PPC4xx family */
	#define CONFIG_405GP 1
	#define CONFIG_4xx 1
	#define CONFIG_HOSTNAME hcu4

	#define CONFIG_SYS_TEXT_BASE 0xFFFB0000

	/*
	* Include common defines/options for all boards produced by Netstal Maschinen
	*/
	#include "netstal-common.h"

	#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
	#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */

	/*-----------------------------------------------------------------------
	* Base addresses -- Note these are effective addresses where the
	* actual resources get mapped (not physical addresses)
	----------------------------------------------------------------------/
	#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */


	#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
	#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE

	/* ... with on-chip memory here (4KBytes) */
	#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
	#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
	/* Do not set up locked dcache as init ram. */
	#undef CONFIG_SYS_INIT_DCACHE_CS

	/* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
	#define CONFIG_SYS_TEMP_STACK_OCM 1

	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* OCM */
	#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE
	#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)

	/*-----------------------------------------------------------------------
	* Serial Port
	----------------------------------------------------------------------/
	/*
	* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
	* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
	* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
	* The Linux BASE_BAUD define should match this configuration.
	* baseBaud = cpuClock/(uartDivisor*16)
	* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
	* set Linux BASE_BAUD to 403200.
	*/
	#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
	#define CONFIG_SYS_BASE_BAUD 691200

	/* Set console baudrate to 9600 */
	#define CONFIG_BAUDRATE 9600

	/*-----------------------------------------------------------------------
	* Flash
	----------------------------------------------------------------------/

	/* Use common CFI driver */
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_FLASH_CFI_DRIVER
	/* board provides its own flash_init code */
	#define CONFIG_FLASH_CFI_LEGACY 1
	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
	#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1

	/* print 'E' for empty sector on flinfo */
	#define CONFIG_SYS_FLASH_EMPTY_INFO

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */

	/*-----------------------------------------------------------------------
	* Environment
	----------------------------------------------------------------------/

	#undef CONFIG_ENV_IS_IN_NVRAM
	#define CONFIG_ENV_IS_IN_FLASH
	#undef CONFIG_ENV_IS_NOWHERE

	#ifdef CONFIG_ENV_IS_IN_EEPROM
	/* Put the environment after the SDRAM configuration */
	#define PROM_SIZE 2048
	#define CONFIG_ENV_OFFSET 512
	#define CONFIG_ENV_SIZE (PROM_SIZE-CONFIG_ENV_OFFSET)
	#endif

	#ifdef CONFIG_ENV_IS_IN_FLASH
	/* Put the environment in Flash */
	#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
	#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE 81024 / 8 KB Environment Sector */

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
	#endif

	/*-----------------------------------------------------------------------
	* I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
	* the first internal I2C controller of the PPC440EPx
	----------------------------------------------------------------------/
	#define CONFIG_SYS_SPD_BUS_NUM 0

	#define CONFIG_IPADDR 172.25.1.14

	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_NETSTAL_DEF_ENV \
	CONFIG_NETSTAL_DEF_ENV_POWERPC \
	""

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_CACHE
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_DIAG
	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_FLASH
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IMMAP
	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_NET
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_REGINFO
	#define CONFIG_CMD_SDRAM

	/* SPD EEPROM (sdram speed config) disabled */
	#define CONFIG_SPD_EEPROM 1
	#define SPD_EEPROM_ADDRESS 0x50

	/* POST support */
	#define CONFIG_POST (CONFIG_SYS_POST_MEMORY \| \
	CONFIG_SYS_POST_CPU \| \
	CONFIG_SYS_POST_UART \| \
	CONFIG_SYS_POST_I2C \| \
	CONFIG_SYS_POST_CACHE \| \
	CONFIG_SYS_POST_ETHER \| \
	CONFIG_SYS_POST_SPR)

	#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
	#undef CONFIG_LOGBUFFER
	#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
	#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */

	/*-----------------------------------------------------------------------
	* Miscellaneous configurable options
	----------------------------------------------------------------------/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */


	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	/*-----------------------------------------------------------------------
	* External Bus Controller (EBC) Setup
	*/

	#define CONFIG_SYS_EBC_CFG 0x98400000

	/* Memory Bank 0 (Flash Bank 0) initialization */
	#define CONFIG_SYS_EBC_PB0AP 0x02005400
	#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */

	#define CONFIG_SYS_EBC_PB1AP 0x03041200
	#define CONFIG_SYS_EBC_PB1CR 0x7009A000 /* BAS=,BS=MB,BU=R/W,BW=bit */

	#define CONFIG_SYS_EBC_PB2AP 0x02054500
	#define CONFIG_SYS_EBC_PB2CR 0x78018000 /* BAS=,BS=MB,BU=R/W,BW=bit */

	#define CONFIG_SYS_EBC_PB3AP 0x01840300
	#define CONFIG_SYS_EBC_PB3CR 0x7c0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */

	#define CONFIG_SYS_EBC_PB4AP 0x01800300
	#define CONFIG_SYS_EBC_PB4CR 0x7e0ba000 /* BAS=,BS=MB,BU=R/W,BW=bit */

	#define CONFIG_SYS_GPIO0_OR 0xF27FFFFF /* GPIO value */
	#define CONFIG_SYS_GPIO0_TCR 0x7FFE0000 /* GPIO value */
	#define CONFIG_SYS_GPIO0_ODR 0x00E897FC /* GPIO value */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */

	/* Init Memory Controller:
	*
	* BR0/1 and OR0/1 (FLASH)
	*/

	#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
	#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */


	/* Configuration Port location */
	#define CONFIG_PORT_ADDR 0xF0000500

	#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
	#ifdef CONFIG_SYS_HUSH_PARSER
	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
	#endif

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif

	#endif /* __CONFIG_H */