| CONFIG_ARM=y |
| CONFIG_ARCH_IMX8M=y |
| CONFIG_SYS_TEXT_BASE=0x40200000 |
| CONFIG_SYS_MALLOC_LEN=0x600000 |
| CONFIG_SPL_GPIO=y |
| CONFIG_SPL_LIBCOMMON_SUPPORT=y |
| CONFIG_SPL_LIBGENERIC_SUPPORT=y |
| CONFIG_SYS_MALLOC_F_LEN=0x4000 |
| CONFIG_ENV_SIZE=0x1000 |
| CONFIG_ENV_OFFSET=0x400000 |
| CONFIG_SYS_I2C_MXC_I2C1=y |
| CONFIG_SYS_I2C_MXC_I2C2=y |
| CONFIG_SYS_I2C_MXC_I2C3=y |
| CONFIG_DM_GPIO=y |
| CONFIG_DEFAULT_DEVICE_TREE="imx8mq-phanbell" |
| CONFIG_SPL_TEXT_BASE=0x7E1000 |
| CONFIG_TARGET_IMX8MQ_PHANBELL=y |
| CONFIG_SPL_MMC=y |
| CONFIG_SPL_SERIAL=y |
| CONFIG_SPL_DRIVERS_MISC=y |
| CONFIG_SPL=y |
| CONFIG_SYS_LOAD_ADDR=0x40480000 |
| CONFIG_FIT=y |
| CONFIG_FIT_EXTERNAL_OFFSET=0x3000 |
| CONFIG_SPL_LOAD_FIT=y |
| CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" |
| CONFIG_SD_BOOT=y |
| CONFIG_BOARD_EARLY_INIT_F=y |
| CONFIG_SPL_BOARD_INIT=y |
| CONFIG_SPL_I2C=y |
| CONFIG_SPL_POWER=y |
| CONFIG_HUSH_PARSER=y |
| # CONFIG_BOOTM_NETBSD is not set |
| # CONFIG_CMD_EXPORTENV is not set |
| # CONFIG_CMD_IMPORTENV is not set |
| # CONFIG_CMD_CRC32 is not set |
| CONFIG_CMD_FUSE=y |
| CONFIG_CMD_GPIO=y |
| CONFIG_CMD_I2C=y |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_DHCP=y |
| CONFIG_CMD_MII=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_CACHE=y |
| CONFIG_CMD_REGULATOR=y |
| CONFIG_CMD_EXT2=y |
| CONFIG_CMD_EXT4=y |
| CONFIG_CMD_EXT4_WRITE=y |
| CONFIG_CMD_FAT=y |
| # CONFIG_SPL_DOS_PARTITION is not set |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_OVERWRITE=y |
| CONFIG_ENV_IS_IN_MMC=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_SYS_MMC_ENV_DEV=1 |
| CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000 |
| CONFIG_DM_I2C=y |
| CONFIG_SPL_SYS_I2C_LEGACY=y |
| CONFIG_SUPPORT_EMMC_BOOT=y |
| CONFIG_FSL_USDHC=y |
| CONFIG_DM_ETH=y |
| CONFIG_FEC_MXC=y |
| CONFIG_PINCTRL=y |
| CONFIG_PINCTRL_IMX8M=y |
| CONFIG_SPL_POWER_LEGACY=y |
| CONFIG_POWER_DOMAIN=y |
| CONFIG_IMX8M_POWER_DOMAIN=y |
| CONFIG_DM_REGULATOR=y |
| CONFIG_DM_REGULATOR_FIXED=y |
| CONFIG_DM_REGULATOR_GPIO=y |
| CONFIG_SPL_POWER_I2C=y |
| CONFIG_DM_RESET=y |
| CONFIG_MXC_UART=y |
| CONFIG_DM_THERMAL=y |