blob: 28ddcf85a36f177d31c893a3de8c6d929d066bfa [file] [log] [blame]
menu "SPI Support"
config DM_SPI
bool "Enable Driver Model for SPI drivers"
depends on DM
help
Enable driver model for SPI. The SPI slave interface
(spi_setup_slave(), spi_xfer(), etc.) is then implemented by
the SPI uclass. Drivers provide methods to access the SPI
buses that they control. The uclass interface is defined in
include/spi.h. The existing spi_slave structure is attached
as 'parent data' to every slave on each bus. Slaves
typically use driver-private data instead of extending the
spi_slave structure.
if DM_SPI
config ALTERA_SPI
bool "Altera SPI driver"
help
Enable the Altera SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Altera
IP core. Please find details on the "Embedded Peripherals IP
User Guide" of Altera.
config ATH79_SPI
bool "Atheros SPI driver"
depends on ARCH_ATH79
help
Enable the Atheros ar7xxx/ar9xxx SoC SPI driver, it was used
to access SPI NOR flash and other SPI peripherals. This driver
uses driver model and requires a device tree binding to operate.
please refer to doc/device-tree-bindings/spi/spi-ath79.txt.
config ATMEL_SPI
bool "Atmel SPI driver"
depends on ARCH_AT91
help
This enables driver for the Atmel SPI Controller, present on
many AT91 (ARM) chips. This driver can be used to access
the SPI Flash, such as AT25DF321.
config BCM63XX_HSSPI
bool "BCM63XX HSSPI driver"
depends on ARCH_BMIPS
help
Enable the BCM6328 HSSPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Broadcom
SPI core.
config BCM63XX_SPI
bool "BCM6348 SPI driver"
depends on ARCH_BMIPS
help
Enable the BCM6348/BCM6358 SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding these Broadcom
SPI cores.
config CADENCE_QSPI
bool "Cadence QSPI driver"
help
Enable the Cadence Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Cadence IP core.
config DESIGNWARE_SPI
bool "Designware SPI driver"
help
Enable the Designware SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Designware
IP core.
config EXYNOS_SPI
bool "Samsung Exynos SPI driver"
help
Enable the Samsung Exynos SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Samsung
Exynos IP core.
config FSL_DSPI
bool "Freescale DSPI driver"
help
Enable the Freescale DSPI driver. This driver can be used to
access the SPI NOR flash and SPI Data flash on platforms embedding
this Freescale DSPI IP core. LS102xA and Colibri VF50/VF61 platforms
use this driver.
config ICH_SPI
bool "Intel ICH SPI driver"
help
Enable the Intel ICH SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Intel
ICH IP core.
config MVEBU_A3700_SPI
bool "Marvell Armada 3700 SPI driver"
help
Enable the Marvell Armada 3700 SPI driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Marvell IP core.
config PIC32_SPI
bool "Microchip PIC32 SPI driver"
depends on MACH_PIC32
help
Enable the Microchip PIC32 SPI driver. This driver can be used
to access the SPI NOR flash, MMC-over-SPI on platforms based on
Microchip PIC32 family devices.
config ROCKCHIP_SPI
bool "Rockchip SPI driver"
help
Enable the Rockchip SPI driver, used to access SPI NOR flash and
other SPI peripherals (such as the Chrome OS EC) on Rockchip SoCs.
This uses driver model and requires a device tree binding to
operate.
config SANDBOX_SPI
bool "Sandbox SPI driver"
depends on SANDBOX && DM
help
Enable SPI support for sandbox. This is an emulation of a real SPI
bus. Devices can be attached to the bus using the device tree
which specifies the driver to use. As an example, see this device
tree fragment from sandbox.dts. It shows that the SPI bus has a
single flash device on chip select 0 which is emulated by the driver
for "sandbox,spi-flash", which is in drivers/mtd/spi/sandbox.c.
spi@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
compatible = "sandbox,spi";
cs-gpios = <0>, <&gpio_a 0>;
flash@0 {
reg = <0>;
compatible = "spansion,m25p16", "sandbox,spi-flash";
spi-max-frequency = <40000000>;
sandbox,filename = "spi.bin";
};
};
config STM32_QSPI
bool "STM32F7 QSPI driver"
depends on STM32F7
help
Enable the STM32F7 Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash chips on platforms embedding
this ST IP core.
config TEGRA114_SPI
bool "nVidia Tegra114 SPI driver"
help
Enable the nVidia Tegra114 SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this nVidia Tegra114
IP core.
This controller is different than the older SoCs SPI controller and
also register interface get changed with this controller.
config TEGRA20_SFLASH
bool "nVidia Tegra20 Serial Flash controller driver"
help
Enable the nVidia Tegra20 Serial Flash controller driver. This driver
can be used to access the SPI NOR flash on platforms embedding this
nVidia Tegra20 IP core.
config TEGRA20_SLINK
bool "nVidia Tegra20/Tegra30 SLINK driver"
help
Enable the nVidia Tegra20/Tegra30 SLINK driver. This driver can
be used to access the SPI NOR flash on platforms embedding this
nVidia Tegra20/Tegra30 IP cores.
config TEGRA210_QSPI
bool "nVidia Tegra210 QSPI driver"
help
Enable the Tegra Quad-SPI (QSPI) driver for T210. This driver
be used to access SPI chips on platforms embedding this
NVIDIA Tegra210 IP core.
config XILINX_SPI
bool "Xilinx SPI driver"
help
Enable the Xilinx SPI driver from the Xilinx EDK. This SPI
controller support 8 bit SPI transfers only, with or w/o FIFO.
For more info on Xilinx SPI Register Definitions and Overview
see driver file - drivers/spi/xilinx_spi.c
config ZYNQ_SPI
bool "Zynq SPI driver"
depends on ARCH_ZYNQ || ARCH_ZYNQMP
help
Enable the Zynq SPI driver. This driver can be used to
access the SPI NOR flash on platforms embedding this Zynq
SPI IP core.
config ZYNQ_QSPI
bool "Zynq QSPI driver"
depends on ARCH_ZYNQ
help
Enable the Zynq Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Zynq QSPI IP core. This IP is used to connect the flash in
4-bit qspi, 8-bit dual stacked and shared 4-bit dual parallel.
endif # if DM_SPI
config SOFT_SPI
bool "Soft SPI driver"
help
Enable Soft SPI driver. This driver is to use GPIO simulate
the SPI protocol.
config FSL_ESPI
bool "Freescale eSPI driver"
help
Enable the Freescale eSPI driver. This driver can be used to
access the SPI interface and SPI NOR flash on platforms embedding
this Freescale eSPI IP core.
config FSL_QSPI
bool "Freescale QSPI driver"
help
Enable the Freescale Quad-SPI (QSPI) driver. This driver can be
used to access the SPI NOR flash on platforms embedding this
Freescale IP core.
config ATCSPI200_SPI
bool "Andestech ATCSPI200 SPI driver"
help
Enable the Andestech ATCSPI200 SPI driver. This driver can be
used to access the SPI flash on AE3XX and AE250 platforms embedding
this Andestech IP core.
config TI_QSPI
bool "TI QSPI driver"
help
Enable the TI Quad-SPI (QSPI) driver for DRA7xx and AM43xx evms.
This driver support spi flash single, quad and memory reads.
config MPC8XX_SPI
bool "MPC8XX SPI Driver"
depends on 8xx
help
Enable support for SPI on MPC8XX
config OMAP3_SPI
bool "McSPI driver for OMAP"
help
SPI master controller for OMAP24XX and later Multichannel SPI
(McSPI). This driver be used to access SPI chips on platforms
embedding this OMAP3 McSPI IP core.
endmenu # menu "SPI Support"