include/configs/controlcenterdc.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) 2014 Stefan Roese <sr@denx.de>
  * Copyright (C) 2016 Mario Six <mario.six@gdsys.cc>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef _CONFIG_CONTROLCENTERDC_H
 #define _CONFIG_CONTROLCENTERDC_H

 /*
  * High Level Configuration Options (easy to change)
  */
 #define CONFIG_CUSTOMER_BOARD_SUPPORT

 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 #define CONFIG_BOARD_LATE_INIT

 /*
  * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
  * for DDR ECC byte filling in the SPL before loading the main
  * U-Boot into it.
  */

 #define CONFIG_SYS_TCLK		250000000	/* 250MHz */

 #define CONFIG_LOADADDR 		1000000

 /*
  * Commands configuration
  */
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_SPI

 /* SPI NOR flash default params, used by sf commands */
 #define CONFIG_SF_DEFAULT_BUS		1
 #define CONFIG_SF_DEFAULT_SPEED		1000000
 #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_3

 /*
  * SDIO/MMC Card Configuration
  */
 #define CONFIG_SYS_MMC_BASE		MVEBU_SDIO_BASE

 /*
  * SATA/SCSI/AHCI configuration
  */
 #define CONFIG_SCSI_AHCI_PLAT
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
 #define CONFIG_SYS_SCSI_MAX_LUN		1
 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 					 CONFIG_SYS_SCSI_MAX_LUN)

 /* USB/EHCI configuration */
 #define CONFIG_EHCI_IS_TDI

 /* Environment in SPI NOR flash */
 #define CONFIG_ENV_SPI_BUS		1
 #define CONFIG_ENV_OFFSET		(1 << 20) /* 1MiB in */
 #define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
 #define CONFIG_ENV_SECT_SIZE		(256 << 10) /* 256KiB sectors */

 #define CONFIG_PHY_MARVELL		/* there is a marvell phy */
 #define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */

 /* PCIe support */
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_PCI
 #define CONFIG_PCI_MVEBU
 #define CONFIG_PCI_PNP
 #define CONFIG_PCI_SCAN_SHOW
 #endif

 /*
  * Software (bit-bang) MII driver configuration
  */
 #define CONFIG_BITBANGMII		/* bit-bang MII PHY management */
 #define CONFIG_BITBANGMII_MULTI

 /* SPL */
 /*
  * Select the boot device here
  *
  * Currently supported are:
  * SPL_BOOT_SPI_NOR_FLASH	- Booting via SPI NOR flash
  * SPL_BOOT_SDIO_MMC_CARD	- Booting via SDIO/MMC card (partition 1)
  */
 #define SPL_BOOT_SPI_NOR_FLASH		1
 #define SPL_BOOT_SDIO_MMC_CARD		2
 #define CONFIG_SPL_BOOT_DEVICE		SPL_BOOT_SPI_NOR_FLASH

 /* Defines for SPL */
 #define CONFIG_SPL_SIZE			(160 << 10)

 #if defined(CONFIG_SECURED_MODE_IMAGE)
 #define CONFIG_SPL_TEXT_BASE		0x40002614
 #define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - 0x2614)
 #else
 #define CONFIG_SPL_TEXT_BASE		0x40000030
 #define CONFIG_SPL_MAX_SIZE		(CONFIG_SPL_SIZE - 0x30)
 #endif

 #define CONFIG_SPL_BSS_START_ADDR	(0x40000000 + CONFIG_SPL_SIZE)
 #define CONFIG_SPL_BSS_MAX_SIZE		(16 << 10)

 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MALLOC_SIMPLE
 #endif

 #define CONFIG_SPL_STACK		(0x40000000 + ((212 - 16) << 10))
 #define CONFIG_SPL_BOOTROM_SAVE		(CONFIG_SPL_STACK + 4)

 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT

 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
 /* SPL related SPI defines */
 #define CONFIG_SYS_SPI_U_BOOT_OFFS	0x30000
 #define CONFIG_SYS_U_BOOT_OFFS		CONFIG_SYS_SPI_U_BOOT_OFFS
 #endif

 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
 /* SPL related MMC defines */
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
 #define CONFIG_SYS_MMC_U_BOOT_OFFS		(168 << 10)
 #define CONFIG_SYS_U_BOOT_OFFS			CONFIG_SYS_MMC_U_BOOT_OFFS
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	(CONFIG_SYS_U_BOOT_OFFS / 512)
 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER	0x00180000	/* in SDRAM */
 #endif
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #define CONFIG_BAUDRATE 115200

 #define CONFIG_HOSTNAME		"ccdc"
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
 #define CONFIG_BOOTFILE		"ccdc.img"

 #define CONFIG_PREBOOT		/* enable preboot variable */

 #define CONFIG_EXTRA_ENV_SETTINGS						\
 	"netdev=eth1\0"						\
 	"consoledev=ttyS1\0"							\
 	"u-boot=u-boot.bin\0"							\
 	"bootfile_addr=1000000\0"						\
 	"keyprogram_addr=3000000\0"						\
 	"keyprogram_file=keyprogram.img\0"						\
 	"fdtfile=controlcenterdc.dtb\0"						\
 	"load=tftpboot ${loadaddr} ${u-boot}\0"					\
 	"mmcdev=0:2\0"								\
 	"update=sf probe 1:0;"							\
 		" sf erase 0 +${filesize};"					\
 		" sf write ${fileaddr} 0 ${filesize}\0"				\
 	"upd=run load update\0"							\
 	"fdt_high=0x10000000\0"							\
 	"initrd_high=0x10000000\0"						\
 	"loadkeyprogram=tpm flush_keys;"					\
 		" mmc rescan;"							\
 		" ext4load mmc ${mmcdev} ${keyprogram_addr} ${keyprogram_file};"\
 		" source ${keyprogram_addr}:script@1\0"				\
 	"gpio1=gpio@22_25\0"							\
 	"gpio2=A29\0"								\
 	"blinkseq='0 0 0 0 2 0 2 2 3 1 3 1 0 0 2 2 3 1 3 3 2 0 2 2 3 1 1 1 "	\
 		  "2 0 2 2 3 1 3 1 0 0 2 0 3 3 3 1 2 0 0 0 3 1 1 1 0 0 0 0'\0"	\
 	"bootfail=for i in ${blinkseq}; do"					\
 		" if test $i -eq 0; then"					\
 		" gpio clear ${gpio1}; gpio set ${gpio2};"			\
 		" elif test $i -eq 1; then"					\
 		" gpio clear ${gpio1}; gpio clear ${gpio2};"			\
 		" elif test $i -eq 2; then"					\
 		" gpio set ${gpio1}; gpio set ${gpio2};"			\
 		" else;"							\
 		" gpio clear ${gpio1}; gpio set ${gpio2};"			\
 		" fi; sleep 0.12; done\0"

 #define CONFIG_NFSBOOTCOMMAND								\
 	"setenv bootargs root=/dev/nfs rw "						\
 	"nfsroot=${serverip}:${rootpath} "						\
 	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off "	\
 	"console=${consoledev},${baudrate} ${othbootargs}; "				\
 	"tftpboot ${bootfile_addr} ${bootfile}; "						\
 	"bootm ${bootfile_addr}"

 #define CONFIG_MMCBOOTCOMMAND					\
 	"setenv bootargs root=/dev/mmcblk0p3 rw rootwait "	\
 	"console=${consoledev},${baudrate} ${othbootargs}; "	\
 	"ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; "	\
 	"bootm ${bootfile_addr}"

 #define CONFIG_BOOTCOMMAND			\
 	"if env exists keyprogram; then;"	\
 	" setenv keyprogram; run nfsboot;"	\
         " fi;"					\
         " run dobootfail"

 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros
  */
 #include "mv-common.h"

 #endif /* _CONFIG_CONTROLCENTERDC_H */
	/*
	* Copyright (C) 2014 Stefan Roese <sr@denx.de>
	* Copyright (C) 2016 Mario Six <mario.six@gdsys.cc>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef _CONFIG_CONTROLCENTERDC_H
	#define _CONFIG_CONTROLCENTERDC_H

	/*
	* High Level Configuration Options (easy to change)
	*/
	#define CONFIG_CUSTOMER_BOARD_SUPPORT

	#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
	#define CONFIG_BOARD_LATE_INIT

	/*
	* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
	* for DDR ECC byte filling in the SPL before loading the main
	* U-Boot into it.
	*/

	#define CONFIG_SYS_TCLK 250000000 /* 250MHz */

	#define CONFIG_LOADADDR 1000000

	/*
	* Commands configuration
	*/
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_SPI

	/* SPI NOR flash default params, used by sf commands */
	#define CONFIG_SF_DEFAULT_BUS 1
	#define CONFIG_SF_DEFAULT_SPEED 1000000
	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3

	/*
	* SDIO/MMC Card Configuration
	*/
	#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE

	/*
	* SATA/SCSI/AHCI configuration
	*/
	#define CONFIG_SCSI_AHCI_PLAT
	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
	#define CONFIG_SYS_SCSI_MAX_LUN 1
	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	CONFIG_SYS_SCSI_MAX_LUN)

	/* USB/EHCI configuration */
	#define CONFIG_EHCI_IS_TDI

	/* Environment in SPI NOR flash */
	#define CONFIG_ENV_SPI_BUS 1
	#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
	#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
	#define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */

	#define CONFIG_PHY_MARVELL /* there is a marvell phy */
	#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */

	/* PCIe support */
	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_PCI
	#define CONFIG_PCI_MVEBU
	#define CONFIG_PCI_PNP
	#define CONFIG_PCI_SCAN_SHOW
	#endif

	/*
	* Software (bit-bang) MII driver configuration
	*/
	#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
	#define CONFIG_BITBANGMII_MULTI

	/* SPL */
	/*
	* Select the boot device here
	*
	* Currently supported are:
	* SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
	* SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1)
	*/
	#define SPL_BOOT_SPI_NOR_FLASH 1
	#define SPL_BOOT_SDIO_MMC_CARD 2
	#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH

	/* Defines for SPL */
	#define CONFIG_SPL_SIZE (160 << 10)

	#if defined(CONFIG_SECURED_MODE_IMAGE)
	#define CONFIG_SPL_TEXT_BASE 0x40002614
	#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x2614)
	#else
	#define CONFIG_SPL_TEXT_BASE 0x40000030
	#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x30)
	#endif

	#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
	#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)

	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_SYS_MALLOC_SIMPLE
	#endif

	#define CONFIG_SPL_STACK (0x40000000 + ((212 - 16) << 10))
	#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)

	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_SERIAL_SUPPORT
	#define CONFIG_SPL_I2C_SUPPORT

	#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
	/* SPL related SPI defines */
	#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x30000
	#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
	#endif

	#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
	/* SPL related MMC defines */
	#define CONFIG_SPL_MMC_SUPPORT
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1
	#define CONFIG_SYS_MMC_U_BOOT_OFFS (168 << 10)
	#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (CONFIG_SYS_U_BOOT_OFFS / 512)
	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
	#endif
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_HOSTNAME "ccdc"
	#define CONFIG_ROOTPATH "/opt/nfsroot"
	#define CONFIG_BOOTFILE "ccdc.img"

	#define CONFIG_PREBOOT /* enable preboot variable */

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth1\0" \
	"consoledev=ttyS1\0" \
	"u-boot=u-boot.bin\0" \
	"bootfile_addr=1000000\0" \
	"keyprogram_addr=3000000\0" \
	"keyprogram_file=keyprogram.img\0" \
	"fdtfile=controlcenterdc.dtb\0" \
	"load=tftpboot ${loadaddr} ${u-boot}\0" \
	"mmcdev=0:2\0" \
	"update=sf probe 1:0;" \
	" sf erase 0 +${filesize};" \
	" sf write ${fileaddr} 0 ${filesize}\0" \
	"upd=run load update\0" \
	"fdt_high=0x10000000\0" \
	"initrd_high=0x10000000\0" \
	"loadkeyprogram=tpm flush_keys;" \
	" mmc rescan;" \
	" ext4load mmc ${mmcdev} ${keyprogram_addr} ${keyprogram_file};"\
	" source ${keyprogram_addr}:script@1\0" \
	"gpio1=gpio@22_25\0" \
	"gpio2=A29\0" \
	"blinkseq='0 0 0 0 2 0 2 2 3 1 3 1 0 0 2 2 3 1 3 3 2 0 2 2 3 1 1 1 " \
	"2 0 2 2 3 1 3 1 0 0 2 0 3 3 3 1 2 0 0 0 3 1 1 1 0 0 0 0'\0" \
	"bootfail=for i in ${blinkseq}; do" \
	" if test $i -eq 0; then" \
	" gpio clear ${gpio1}; gpio set ${gpio2};" \
	" elif test $i -eq 1; then" \
	" gpio clear ${gpio1}; gpio clear ${gpio2};" \
	" elif test $i -eq 2; then" \
	" gpio set ${gpio1}; gpio set ${gpio2};" \
	" else;" \
	" gpio clear ${gpio1}; gpio set ${gpio2};" \
	" fi; sleep 0.12; done\0"

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off " \
	"console=${consoledev},${baudrate} ${othbootargs}; " \
	"tftpboot ${bootfile_addr} ${bootfile}; " \
	"bootm ${bootfile_addr}"

	#define CONFIG_MMCBOOTCOMMAND \
	"setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \
	"console=${consoledev},${baudrate} ${othbootargs}; " \
	"ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; " \
	"bootm ${bootfile_addr}"

	#define CONFIG_BOOTCOMMAND \
	"if env exists keyprogram; then;" \
	" setenv keyprogram; run nfsboot;" \
	" fi;" \
	" run dobootfail"

	/*
	* mv-common.h should be defined after CMD configs since it used them
	* to enable certain macros
	*/
	#include "mv-common.h"

	#endif /* _CONFIG_CONTROLCENTERDC_H */