| /* |
| * (C) Copyright 2004-2014 |
| * Texas Instruments, <www.ti.com> |
| * |
| * Some changes copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| #ifndef _DAVINCI_I2C_H_ |
| #define _DAVINCI_I2C_H_ |
| |
| #define I2C_WRITE 0 |
| #define I2C_READ 1 |
| |
| struct i2c_regs { |
| u32 i2c_oa; |
| u32 i2c_ie; |
| u32 i2c_stat; |
| u32 i2c_scll; |
| u32 i2c_sclh; |
| u32 i2c_cnt; |
| u32 i2c_drr; |
| u32 i2c_sa; |
| u32 i2c_dxr; |
| u32 i2c_con; |
| u32 i2c_iv; |
| u32 res_2c; |
| u32 i2c_psc; |
| }; |
| |
| /* I2C masks */ |
| |
| /* I2C Interrupt Enable Register (I2C_IE): */ |
| #define I2C_IE_SCD_IE (1 << 5) /* Stop condition detect interrupt enable */ |
| #define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */ |
| #define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */ |
| #define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */ |
| #define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */ |
| #define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */ |
| |
| /* I2C Status Register (I2C_STAT): */ |
| |
| #define I2C_STAT_BB (1 << 12) /* Bus busy */ |
| #define I2C_STAT_ROVR (1 << 11) /* Receive overrun */ |
| #define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ |
| #define I2C_STAT_AAS (1 << 9) /* Address as slave */ |
| #define I2C_STAT_SCD (1 << 5) /* Stop condition detect */ |
| #define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ |
| #define I2C_STAT_RRDY (1 << 3) /* Receive data ready */ |
| #define I2C_STAT_ARDY (1 << 2) /* Register access ready */ |
| #define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */ |
| #define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */ |
| |
| /* I2C Interrupt Code Register (I2C_INTCODE): */ |
| |
| #define I2C_INTCODE_MASK 7 |
| #define I2C_INTCODE_NONE 0 |
| #define I2C_INTCODE_AL 1 /* Arbitration lost */ |
| #define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */ |
| #define I2C_INTCODE_ARDY 3 /* Register access ready */ |
| #define I2C_INTCODE_RRDY 4 /* Rcv data ready */ |
| #define I2C_INTCODE_XRDY 5 /* Xmit data ready */ |
| #define I2C_INTCODE_SCD 6 /* Stop condition detect */ |
| |
| /* I2C Configuration Register (I2C_CON): */ |
| |
| #define I2C_CON_EN (1 << 5) /* I2C module enable */ |
| #define I2C_CON_STB (1 << 4) /* Start byte mode (master mode only) */ |
| #define I2C_CON_MST (1 << 10) /* Master/slave mode */ |
| #define I2C_CON_TRX (1 << 9) /* Tx/Rx mode (master mode only) */ |
| #define I2C_CON_XA (1 << 8) /* Expand address */ |
| #define I2C_CON_STP (1 << 11) /* Stop condition (master mode only) */ |
| #define I2C_CON_STT (1 << 13) /* Start condition (master mode only) */ |
| #define I2C_CON_FREE (1 << 14) /* Free run on emulation */ |
| |
| #define I2C_TIMEOUT 0xffff0000 /* Timeout mask for poll_i2c_irq() */ |
| |
| #endif |